GMW GMW3293-2011 Hexagon Nut and Washer Assemblies with Plain Washer Product Grade A Issue 4 English [Replaced GMW GMW3293 GMW GMW3293]《A等级带有普通垫圈产品的六角螺母和垫圈组件 第4次出版(英文版本)[代替 GMW GMW.pdf

1、 WORLDWIDE ENGINEERING STANDARDS General Specification GMW3293 Hexagon Nut and Washer Assemblies with Plain Washer Product Grade A Copyright 2011 General Motors Company All Rights Reserved October 2011 Originating Department: North American Engineering Standards Page 1 of 4 1 Introduction 1.1 Scope.

2、 This standard gives specifications for hexagon nuts to ISO 4032 with thread diameters from M5 to M8, and plain washer to ISO 7089 non-detachable, turnable. See Figure 1. 1.2 Designation. GMW3293. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 Ex

3、ternal Standards/Specifications. ISO 724 ISO 4759-2 ISO 898-2 ISO 4759-3 ISO 965 ISO 6157-2 ISO 1502 ISO 7089 ISO 4032 ISO T/S 16949 2.2 GM Standards/Specifications. GMW3059 3 Requirements Figure 1: Hexagon Nut with Plain Washer Provided by IHSNot for ResaleNo reproduction or networking permitted wi

4、thout license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW3293 Copyright 2011 General Motors Company All Rights Reserved October 2011 Page 2 of 4 3.1 Dimensions. See Figure 2. Figure 2: Dimension Illustration Table 1: Dimensions Diameter M5 M6 M8 P Pitch 0.8 1 1.25 da Maximum 5.75 6.75 8.75 M

5、inimum 5 6 8 ds Maximum 10 12 16 Minimum 9.64 11.57 15.57 e Minimum 8.79 11.05 14.38 h 1 0.1 1.6 0.2 1.6 0.2 h1 5.8 7 8.6 m Maximum 4.7 5.2 6.8 Minimum 4.4 4.9 6.44 mw Minimum 3.5 3.9 5.2 s Maximum 8 10 13 Minimum 7.78 9.78 12.73 Property Class 8 8 8 Note 1: Flat washer non-detachable, turnable. Pro

6、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW3293 Copyright 2011 General Motors Company All Rights Reserved October 2011 Page 3 of 4 3.2 Material. Nut: Steel, ISO 898-2. See Table 1 for property class for each nu

7、t diameter. Washer: Spring steel, hardness 200 to 250 HV. 3.3 Surface Treatment. As specified on the detail drawing. 3.4 Thread. ISO 724, ISO 965-1. Thread tolerance, recommended 6G before surface treatment. After surface treatment, the thread shall be gaged according to ISO 1502 with a GO-gage of t

8、olerance H. 3.5 Tolerances. Product Grade A, ISO 4759-1, ISO 4759-3. 3.6 Surface Discontinuities. ISO 6157-2. 3.7 Proof Load Requirements. According to ISO 898-2. 3.8 Acceptability. ISO/TS 16949, GM Production Part Approval Process (PPAP). 4 Rules and Regulations 4.1 Legal Regulations. All materials

9、 must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 4.2 Language. In the event of conflict between the English and domestic language, the English language shall take precedence. 4.3 Inspection and Rejection. Samples of components or materials released

10、 to a GM general specification shall be tested for conformity with the requirements of this general specification and approved by the responsible Engineering department prior to commencement of delivery of bulk supplies. A new approval must be received for any changes, e.g., properties, manufacturin

11、g process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial release must be completed. It is the responsibility of the supplier to inform the customer in a timely manner, without solicitation, and to include documentation of all modif

12、ications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeated and documented by the supplier prior to commencement of delivery of non-conforming bulk supplies. In individual cases, a shorter test can be agreed to between the respo

13、nsible Engineering department and the supplier. 4.4 Initial Source Approval. Not applicable 4.5 All materials supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 5 Notes 5.1 Glossary. Not applicable. 5.2 Acronyms, Abbreviations, and

14、 Symbols. PPAP Production Part Approval Process 6 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: GMW3293 7 Release and Revisions This standard was originated in May 1999. It was first approved by Fasteners Engineering in February 2000. It was first pu

15、blished in June 2000. Issue Publication Date Description (Organization) 1 JUN 2000 Initial publication. 2 JUN 2001 Editorial revision. (GMNA) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW3293 Copyright 2011 Ge

16、neral Motors Company All Rights Reserved October 2011 Page 4 of 4 Issue Publication Date Description (Organization) 3 MAY 2005 Reformatted, 3.3. (Fasteners Group) 4 OCT 2011 Five year refresh. Removed part numbers and finish from the spec, revised M10 WAF from 16 mm to 15 mm. (Fasteners Global Council) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-