GOST ISO 4635-2013 Preformed rubber joint seals for use between concrete paving sections of highways Technical requirements《高速公路混凝土铺路段之间用预压制橡胶密封件 技术要求》.pdf

1、 , () INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION (ISC) ISO 46352013 , (ISO 4635:2011, IDT) 2014 ISO 46352013 II , 1.092 . 1.22009 . , . , , , 1 160 - , - - () , 4 2 3 , (- 27 2013 . 59-) : ( 3166) 00497 ( 3166) 00497 AM BY KG MD - RU TJ UA 4 ISO 4635:2011 Rubber, vulcanized

2、Preformed joint seals for use between concrete paving sections of highways Specification ( . , . ) SC 4 ( ) - ISO/TC 45 - (ISO). (en). - 1.52001 ( 3.6). ISO 46352013 III , - , , , . -. - . (IDT) 5 28.03.2014 . 260- ISO 46352013 - 1 2016 . 6 - , . () - - . , , 2014 -, - ISO 46352013 IV 1 .1 2 1 3 .2

3、4 3 5 3 6 .3 7 , .8 () .9 () 10 . () 13 ISO 46352013 1 , Preformed rubber joint seals for use between concrete paving sections of highways. Technical requirements 20160101 - , . . 1 , , - . , , - . , . (CR) - (EPDM). 2 . - , - ( ). ISO 37 Rubber, vulcanized or thermoplastic Determination of tensile

4、stress-strain properties (- . ) ISO 48:2010 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) . ( 10 IRHD 100 IRHD) ISO 188 Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance test ( . ) ISO 815-1:2008 Rubber, vulcanized or t

5、hermoplastic Determination of compression set Part 1: At ambient or elevated temperatures ( . - . 1. -) ISO 46352013 2 ISO 815-2:2008 Rubber, vulcanized or thermoplastic Determination of compression set Part 2: At low temperatures ( . . 2. ) ISO 1431-1 Rubber, vulcanized or thermoplastic Resistance

6、to ozone cracking Part 1: Static and dynamic strain testing ( . . 1. ) ISO 1817 Rubber, vulcanized or thermoplastic Determination of the effect of liquids ( - . ) ISO 2230 Rubber products Guidelines for storage ( . -) ISO 2285 Rubber, vulcanized or thermoplastic Determination of tension set under co

7、nstant elonga-tion, and of tension set, elongation and creep under constant tensile load ( . , ) ISO 3302-1:1996 Rubber Tolerances for products Part 1: Dimensional tolerances (. - . 1. ) ISO 3384-1:2005 Rubber, vulcanized or thermoplastic Determination of stress relaxation in com-pression Part 1: Te

8、sting at constant temperature ( . - . 1. )1) ISO 3387 Rubber Determination of crystallization effects by hardness measurements (. - ) ISO 5893 Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification . , ( ). ISO 23529 Rubber General proced

9、ures for preparing and conditioning test pieces for physical test methods (. - ) 3 : 3.1 (joint): - , . 3.2 (joint chamber): - . - . , - , . 3.3 (preformed joint seal): () - , - , . - . 3.4 , IRHD (international rubber hardness degree, IRHD): , . 1 , , (IRHD). IRHD, -1) ISO 3384-1:2011. ISO 46352013

10、 3 . IRHD, -. 2 IRHD ISO 48. 4 1. 1 40 50 60 70 80 IRHD . 35 45 . . 45 55 . . 55 65 . . 65 75 . . 75 85 . 5 5.1 , - ISO 23529. - , , , , , . 5.2 , ISO 23529. 6 6.1 6.1.1 (. 6.11); - , , . 6.1.2 . 6.2 ISO 3302-1 1 2 ISO 3302-1. 6.3 . , . 6.4 6.4.1 ISO 48 ( ). , 2 ( 1.1). 6.4.2 - 5 . 5 IRHD. , (. 2, 1

11、.2). ISO 46352013 4 6.5 6.5.1 , ISO 23529, , , . 6.5.2 ISO 37 ( 2). 2 ( 2, 3). 2 40 50 60 70 80 1.1 , IRHD 6.4 . 35 45 . . 45 55 . . 55 65 . . 65 75 . . 75 85 . 1.2 , IRHD, 6.4 5 2 , , 6.5 9 3 -, %, 6.5 400 375 300 200 125 4 2022, %, : 70 25 6.6 6.6.2 6.6.3 20 60 5 2072 100 : , IRHD, - 5 -, %, 20 40 , 6.7 30 10 - 40 10 6 100 50 , % 6.8 50 55 7 ), %: 25 70 6.9 65 80 8 - 20168 - 10 ), IRHD, 6.10 15 10 ISO 46352013 5 40 50 60 70 80 9