GSA A-A-1354 A-2002 WRENCH OPEN END SINGLE THIN HEAD 15 DEGREE HEAD《15度单平头开口扳手》.pdf

1、INCWPOUND IA-A-1354AFebruan 6,2002SUPERSEDINGA-A-1354January 14,1980COMMERCIAL ITEM DESCRIPTIONWRENCH, OPEN END, SINGLE THIN HEAD, 15 HEADThe General Services Administration has authorized the use of this commercial item descriptionby all federal agencies.1. SCOPE. This commercial item description c

2、overs wrenches suitable for thin hexagon and square-headed bolts and nuts.2. CLASSIFICATION. Not applicable3. SALIENT CHARACTERISTICS.3.1 Desire. Wrenches shall be designed as to afford a well proportioned, comfortable handgrip.Wrench dimensions and sizes shall conform to section 3.2.Beneficial comm

3、ents, recommendations, additions, deletions, clarifications, etc. and any other datawhich may improve this document should be sent to: General Services Administration, FederalSupply Service, Hardware SuperStore (6FEE), 1500 Bannister Rd. Bldg. #6, Kansas City,Missouri. 64131.FSC 5120Provided by IHSN

4、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1354A3.2 Dimensions and Sizes.Wrench Opening Width Of Head Thickness Of Head Overall Length Test Load(Distance Across Flats) Maximum) (Maximum) (Minimum) (Minimum)Inches Inches Inches Inches Inches7/16 1-3/16 11/64

5、 3-7/8 3201/2 1-3/16 11/64 3-7/8 3203/16 1-3/8 3/16 4-7/16 4755/8 1-9/16 13/64 5-1/16 65011/16 1-9/16 13/64 5-1/16 6503/4 1-27/32 15/64 5-7/8 95013/16 2-3/32 17/64 6-5/8 1,35015/16 2-5/161 2-5/161-1/4 31-5/16 31-1/2 3-3/89/64 7-1/2 1,8009/64 7-1/2 1,8003/32 9-3/4 3,4003/32 9-3/4 3,7805/32 11-1/4 5,8

6、001-5/8 3-15/16 17/32 13 9,0003.3 Materials. The materials used in the manufacturing of the wrenches shall be such as to producewrenches conforming to the physical requirements hereinafter described.3.4 Marking. Each wrench shall be marked on one of the faces or on the handle as close to each head a

7、sis practicable in a plain and permanent manner. In addition to size markings, each wrench shall bemarked in a plain and permanent manner with the manufacturers name or trademark of such knowncharacter that the source of manufacture maybe readily determined.3.5 Hardness. Wrenches shall be treated to

8、 a Rockwell C hardness not less that 38 nor more than 55when tested per ASTM-E- 18.3.6 Tomue Loads. When tested as specified in ASME-B 107.6, the wrenches shall withstand the proofloads specified in the included table without failure or permanent deformation which might affect thedurability or servi

9、ceability of the wrenches3.7 Wrench Opening. The nut and bolt head-engaging surfaces of the open end wrench shall be finishedin a smooth and well-defined manner. The tips (working ends) of all open end wrenches shall also bechamfered or rounded to eliminate burrs. Wrench opening tolerances shall be

10、such as to insureacceptance when gaged with gages conforming to ASME B 107. 17M.3.8 Finish.3.8.1 Surface Finish. All surfaces shall be thoroughly cleaned, free from cracks, and essentially freefrom burrs, pits, nodules, and other detrimental deficiencies.2Provided by IHSNot for ResaleNo reproduction

11、 or networking permitted without license from IHS-,-,-A-A-1 354A3.8.2 Coatings.continuous, andThe coatings shall be black oxide (3.8.2.1). The coating shall be adherent, smooth,free from uncoated areas, pits, blisters, nodules, and any other defects which wouldinterfere with their protective value a

12、nd serviceability.3.8.2.1 Black Oxide. Oxide coated wrenches shall have. a coating consisting of a chemically producedoxide followed by a coating of rust preventive.4. REGULATORY REQUIREMENTS.4.1 Recovered Material. The offeror/contractor is encouraged to use recovered materials to themaximum extent

13、 practicable, in accordance with paragraph 23.403 of the Federal acquisition Regulation(FAR).5. PRODUCT CONFORMANCE.5.1 Product Conformance. The product provided shall meet the salient characteristics of thisCommercial Item Description, conform to the producers own drawing, specifications, standards

14、, andquality assurance practices, and be the same product offered for sale in the commercial market. Thegovernment reserves the right to require proof of such conformance.5.2 Responsibility for Inspection. Unless otherwise specified, the contractor is responsible for theperformance of all inspection

15、 requirements and may use any commercial facilities (including thecontractors own facilities) suitable for performance of the inspection requirements, unless disapprovedby the Government. The Government reserves the right to perform any of the inspections deemednecessary to assure the item conilorms

16、 to the specified requirements.6. PACKAGING. Preservation, packaging and marking shall be as specified in the contract or order.7. NOTES. This section contains information of a general or explanatory nature that is not mandatory.7.1 Source of Documents.American Society of Mechanical Engineers (ASME)

17、 Manuel Gutierrez, Managing Director, 3 ParkAvenue, New York, NY 10016.American Society for testing and Materials (ASTM), 100 Barr Harbor Dr., W. Conshohocken, PA,19428-2959.Federal Acquisition Regulation (FAR): Government Printing Office, Superintendent of Documents,Washington DC. 20401-9371.7.2 Or

18、dering data. Purchasers should select the preferred options permitted herein and should includethe following information in procurement documents.a. Title, number and date of Commercial Item Description.b. Wrench Openingc. Packaging requirements.3Provided by IHSNot for ResaleNo reproduction or netwo

19、rking permitted without license from IHS-,-,-7.3 National Stock Numbers (NSNS).A-A-1354AAlistofNSNs assigned thatcorrespond tothis CID. The listmay not be indicative of all possible NSNs associated with the CID,National Wrench OpeningStock Number (Distance Across Flats)Inches5120-00-064-2614 7/16512

20、0-00-081-9072 %5120-00-081-9073 3/165120-00-081-9074 5185120-00-081-9075 11/165120-00-529-5117 3/45120-00-529-5116 13/165120-00-293-1325 15/165120-00-529-5119 15120-00-293-1797 1-1/45120-00-081-9082 1-5/165120-00-081-9083 1-1/25120-00-529-5118 1-5/87.4 Keywords. Wrench; Open end; Single thinhead; 15head.MILITARY INTERESTS:NONE: DoD has no registeredinterestinrevisions and arnendmentsto thisCommercial Item Description untilfurthernotice.Preparing Activity:GSA-FSS4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-