GSA A-A-180 C-1997 TAPE PRESSURE-SENSITIVE ADHESIVE DOUBLE-COATED《双涂层压敏粘合粘合带》.pdf

1、 A-A-L8OC 9999974 017552b 641 Metric A-A-180C July 24. 1997 Superseding Febniary2,1989 A-A-18OB COMMERCIAL ITEM DESCRIPTION TAPE, PRESSURE-SENSITIVE ADHESIVE DOUBLE-COATED The General Services Administration has authorized the use of this commercial item description by all Federal agencies. 1. ScoDe

2、: This Commercial Item Description covers double-coated tapes used for mounting photos, drawings, mounting plates used for identification, decoration, holding heavier items, such as nameplates on doors or walls. 2. Classification: Type - I. - Transparent film base Class 1. - With liner Class 2. - Wi

3、thout liner Type - II. - Opaque paper base, with liner. Grade A. - Regular holding power Grade B. - High holding power 3. Salient Characteristics: 3.1 Material. The tape shall conform with the requirements specified in accordance with Table 1. 3.2 Workmanshin The tape shall be uniformly constructed

4、and free fi-om defects which may impair usefulness of the material for the intended use. The adhesive shall be coated in a smooth uniform layer over the entire surface of both sides of the tape backing. The tape shall be evenly and tightly wound with no voids. The edges of the roll shall be clean cu

5、t. When unwound, the tape shall not tear nor shall the adhesive separate from the backing. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to General SeMces Administration, Federal Supply Service, Engineerin

6、g Branch, 26 Federal Plaza, New York, NY 10278. FSC 7510 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-L8OC 9999974 0175527 588 54.72 NI100 mm (50 odin) FSC 7510 ASTM D3330 Method B; A-A-18OC I Tensile (lblin) Width, minimum Holding Power, min

7、utes at 49 degrees Celsius., minimum Adhesion (Odin) width, mlliimum a) Initial accelerated Adhesion to (odin) width, a Initiai accelerated Class 1 280.2 Ni100 mm (1 6 lblin) 27.36 NI100 mm (25 odin) 21.89 Nl100 mm (20 Odin) 27.36 NI100 mm (25 ozlin) 21.89 NI100 mm (20 Odin) Table 1. Physical Proper

8、ties Class 2 Grade A Grade B Test Method (16 lblin) (1 5 lblin) (25 lblin) 2.0 ASTM D3654 Procedure C see section 5.2.1 27.36 Ni100 mm (25 odin) 27.36 Nl100 mm (25 odin) (20 0z.h) (25 odin) (50 odin) section 5.2.2 ASTM D3611 16.41 NI100 mm 16.41 NI100 mm ASTM D3330, (1 5 odin) (1 5 odin) I MethodC;

9、I 21.89 NI100 mm (20 Odin) Tye 1-11, ee (20 Odin) Type li, see 4. Repulatorv Reauirements: The offerer/contractor is encouraged to use recovered materiais to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. ualitv Assurance Reauireme

10、nts: 5.1 Product Conformance. The product shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards and quality assurance practices and be the same product offered for sale in the commercial market. The government res

11、erves the right to require proof of such conformance. -2- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-180C 5.2 Testing. Testing shall be in accordance with ASTM D 3 7 15 Section 6 with an AQL of 4 percent defective. The sample unit shall be o

12、ne roll of tape. 5.2.1 Holding Power Test: The holding power test specimen shall be (1/2 inch) 1.27 cm wide, and the area of test on the panel shall be a (1/2 in.) 1.27 cm by (1/2 in.) 1.27 cm square area. The test shall be performed at 49 degrees Celsius using a 500-g load. Both sides of the tape s

13、haU be tested. The specimen shall be prepared for the face side test by removing the liner and adhering the tape liner side to a 1-mil thick polyester film and then cutting a (1/2 inch) 1.27 cm wide specimen. The specimen for the liner side test shall be prepared by first adhering the tape face side

14、 to a 1-mil thick polyester lm, The liner shall then be removed and a (112 inch) 1.27 cm wide specimen cut. 5.2.2 L/ Accelerated Apinp: (Type I tape only) - Two specimens per test roll are required. Each specimen shall be at least (112 inch) 1.27 cm wide and (10 inches) 25.4 cm long. Place (4 inches

15、) 10.16 cm of one specimen, adhesive side down, on a glass plate. Superimpose on each another specimen, adhesive side down, with the end projecting over the glass plate to serve as a starting tab. The starting tab is formed by doubling the adhesive side of the tape on itself. Arrange multiple specim

16、ens so that there is a fiee air space around them. Place a second glass plate over these strips. Add a 1,000 gram weight on the upper glass plate. Place in a container and environment described in ASTM D 36 1 1, and place the assembly in a 49 (1 degree Celsius) oven. Remove assembly from the oven at

17、 the end of 30 hours, remove the weight and upper glass plate, and expose the remainder to a temperature of 23 (2 degree Celsius) and a relative humidity of 50 i 2 percent until equilibrium is achieved. Remove the superimposed tape, and observe and report as a failure any adhesive stringiness or off

18、setting and any tearing or delamination of the backing. Perform the test for adhesion and adhesion to limer. 6. PackaPinp: Preservation, packing and marking shall be specified in the contract or order. 7. Notes: 7.1 Source of Documents. The following documents form a part of the Commercial Item Desc

19、ription to the extent specified herein. Unless otherwise indicated, the issue in effect on the date of invitation for bids or request for proposal shall apply: 7.1.2 American Society of Testing and Materials (ASTM) standard test methods can be obtained from, at 100 Barr Harbor Dr., West Conshohocken

20、, PA 19428-2959. 7.1.3 Federal Acquisition Regulation (FAR) may be obtained fi-om the Superintendent of Documents, Government Printing Office, Washington, DC 20402. -3- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1 80C 7.2 Ordering Data: Purc

21、hasers should select the preferred options permitted herein, and include the following information in procurement documents: A - Title, number and date of this specification. B - Style and Size required. 7.3 National Stock Number Listing (NSNs). The following is a list of NSNs assigned which corresp

22、ond to this CID. The list may not be indicative of all possible NSNs associated with the CID. 75 10-00-904-2663 75 10-00-93 5-5848 Civil Agency Coordinating Activities: DOT NASA Preparing Activity: GSA-FSS I -4- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-