GSA A-A-2113 A-1986 CABINETS WARDROBE AND STORAGE CONTEMPORARY STYLE STEEL GENERAL OFFICE《普通办公用现代式衣橱式储藏钢柜》.pdf

1、A-A-2 11 3A June 20, 1986 SUPERCEDING A-A-2 1 1 3 November 22, 1982 COMMERCIAL ITEM DESCRIPTION CABINETS, WARDROBE AND STORAGE, CONTEMPORARY STYLE, STEEL GENERAL OFFICE The General ;rvl Administration ha- ;iuthri7;pd the use of this Comercial Item Description in preference to Interim Federal Specifi

2、cation AA-C-001770. Salient Characteristics: These characteristics concisely describe the essential physical and functional/performance features of the commercially available items. Design. The cabinets shall be contemporary style intended for heavy duty office use (see attached figures) Types, clas

3、ses, sizes and styles. Type I - Storage cabinets Type II - Combination Storage and Wardrobe Cabinets Type III - Wardrobe Cabinet Class 1 - Double Door Class 2 - Single Door Size 1 - 36“W x 18“D x 78“ minimum Size 2 - 36“W x 18“D x 64“H minimum Size 3 - 18“W x 18“D x 78“H minimum Size 4 - 18“W x 18C)

4、 x 64“ minimum Style A - Left Hand Door Style B - Right Hand Door General construction: The joining of ail the components shall result in compact units of sufficient strength to prevent distortion, breakage or loosening of any component during handling, shipping, daily usage and when moved within th

5、e office. All cabinets shall comply with the specified test requirements. The appearance of the cabinets and the arrangement of interior components shall be generally as shown FSC Tius 7125 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2 in the app

6、licable figures. All cabinets of two-point latch device. The cabinets - ready - for cngqlptp n_nd proper ncspmbly shall have a minimum shall be furnished (chipped knocked-dDwn) or shall be completely and properly assembled by the contractor (shipped set up) as specified by the contracting officer .

7、Face hardware. The face hardware includes a flush pull assembly and a pin or disk tumbler key lock with two keys. The lock shall have not less than 125 key changes. Face hardware shall be polished chrome plate on steel or die cast zinc, or polished anodized aluminum. Coat hooks. Coat hooks shall be

8、commercially available items. Hooks shall be anodized or plated to resist rust. Ends shall be ciose ana smootn. Shelves. Shelves shall be as wide and deep as possible within the limitations of the cabinet construction. Hat shelves shall it by not more than 12 or less than 8 inches. Adjustable shelve

9、s shall have at least one 90 degree flange on front back and each side and additional formations and components when necessary for proper enqagement of shelf supports and compliance with shelf load test. Adjustable shelves in type II cabinets shall extend between the cabinet side and vertical partit

10、ion. be RUnadjustahle arid shall clear the fiearest black shall match Federal Standard No. 595 Color No. 27040; parchment shall be within the range - delineated by Federal Standard No. 595 Nos. 26586 and 26405. Identification label. The label shall have the contractors name or trademark, contract nu

11、mber, NSN (if Specified, montn and year of manufacture legibly marked in dark ink. The label shall be located on the inside of the cabinet, approximately midpoint between the top and bottom. The label shall not be removable by hand without defacement after being affixed for four hours. Workmanship.

12、The workmanship shall be of the quality to produce finished wardrobe and storage cabinets acceptable in Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 appearance, function and serviceability and prevent potential hazard to personnel or their cloth

13、ing. Performance. Each cabinet shall comply with the following requirements. Failure to comply with these requirements shall be cause for rejection. Assembly test. A completely knocked-down cabinet shall be easily set up using common hand tools. Instructions shall. be provided. Door hinge test. This

14、 test shall be conducted on completely assembled cabinets. With the cabinet in an upright position, a 150 pound test load shall be suspended from the door (each door of double door cabinets, but not necessarily at same time) by a rope located not more than three inches back from the latch side of th

15、e top-edge of the door. To preclude tilting or upsetting during the test, counterweights may be placed within the cabinet. In a normal manner the door shall be pivoted back and forth, at least ll degrees in each direction. Each door shall be pivoted each way not less than six times. The weight shall

16、 then be removed from the door. If the door binds when closed or fails in any other respect it shall be considered as having failed the test. Failure to pass the test shall be cause for rejection. Shelf load test. This test shall be performed on shelves in Type 1, class 1 cabinets only. The required

17、 number of shelves for the cabinet being tested shall be adjusted so that they are as equidistant as possible from each other and from the top and bottom of the cabinets. The tests shall be performed consecutively on each shelf. The test area shall be the entire top of the shelf minus three inches f

18、rom each side. A weight of 60 pounds shall be equally distributed on the area specified. The weight shall remain on the-shelf at least 15 minutes. With the weight on the shelf, a measurement shall be taken from the bottom center of the shelf downward to a point of reference established before the we

19、ight was applied. The shelf shall not have more than 1/4 inch deflection while loaded or 1/6 inch permanent deflection after the load is removed. The cabinet shall then be visually examined. Any damage to the shelf support, deformation of any component, cracked or broken welds, or loosening of any f

20、astening device shaL,be cause for rejection. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5 Cabinet Moving Test. This test shall be conducted on one cabinet of each type, class, and size. The load area for all shelves shall be the entire top of th

21、e shelf minus three inches from each side. Coat rods shall be loaded across the entire width of the rod, minus 2 inches on the side. All shelves shall be spaced as equidistant as possible between each other and between the top and bottom of the cabinet. Shelves, bottoms and coat rods shall be loaded

22、 with weights in the amounts shown in table below. The cabinets shall be pushed or pulled at a rate of approximately 3 feet per second for a distance of not less than 25 feet, across a concrete or tile floor. The force shall be applied at a height of 36 to 42 inches above the floor. The weights shal

23、l be removed and the cabinets examined to determine that no part of the shall be no cracked or broken welds, or any looseness of mechanical attachments rLGrr-4- II.PFACC.CI - *e-emt rlnC-ci+4-n n1 e- thara LQUAIGC DULACLSU aiiy psLutaiaci&= Shelves Type I, Class 1, Size 1 6 2 30 Class 2, Size 3 6 4

24、15 Type II, Class 1, Size 1 d 2 15 Type III, Class 1, Size 1 30 Size 2 Class 2, Size 3 15 Size 4 Bottom Coat Rod 30 20 20 15 30 25 30 25 20 15 20 15 Regulatory Requirement. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent prac

25、ticable. Packaging, packing and marking. Packing, packing and marking shall be in accordance with the solicitation. Standard Color. A sample of the specified enamel color is obtainable from the Business Service Center, Federal Supply Service, General Services Administration, Washington, DC 20407 or

26、from the Business Service Center in the nearest General Services Administration Regional Office. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6 Firryrrn 1 LAYJLlLb Type I, Class I, Sizes 1 and 2 Note: Size 2 cabinets do not have hat shelves. Provi

27、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-7 n Type III, Class 2, Sizes 3 and 4 Figure 4 Type I, Class 2, Sizes 3 and 4 Y / Note: Size 4 cabinets do not have hat shelves. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 Figure 5 Type II, Class 1, Sizes 1 and 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-