GSA A-A-2122 F-1993 STANDS OFFICE MACHINE《办公用计算机架》.pdf

1、A-A-2122F 9999974 OLb3881 5T4 Met ri c 1 A-A-2 12 2 F December 3, 1993 SUPERSEDING A-A- 2 12 2E September 21, 1990 COMMERCIAL ITEM DESCRIPTION STANDS, OFFICE MACHINE The General Services Administration has authorized the use of this commercial item description. 1. Scope. The stands shall be contempo

2、rary style, designed for heavy duty office use. 2. Salient characteristics. 2.1 Classification. The machine stands shall be classified by type and color as follows. Type I - Portable stand with drop leaves and panels. Minimum top dimensions - 584.2 mm W X 450.8 nun D. Minimum drop leaf dimensions -

3、304.8 mm W x 450.8 mm D. overall height, including casters, minimum 660.4 m, maximum 685.6 mm. Type II -Portable stand with panels. Minimum top dimensions 806.4 mm W x 450.8 mm D. Overall height, including casters, minimum 660.4 mm, maximum 685.6 nun. Colors - In accordance with Fed. Std. No. 595, s

4、ee 3.2. B - Black G - Gray p - Parchment 3. Requirements. 3.1 Components. 3.1.1 Laminated tops and drop leaves. 3.1.1.1 Laminated tops and drop leaves. Tops and leaves shall be self-edged, covered with HP laminated plastic with backing sheet on the bottom. Laminate shall be walnut grain per GSA Stan

5、dard No. FSS-E-01002 or white leather per GSA Standard No. FSS-L-01001, as specified by the contracting officer. r i b , FSC 7110 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2122F 9999974 0163882 430 A-A-2 122 F Alternatively, the manufacture

6、r may provide his equivalent commercial walnut grain and white leather HP laminated plastic subject to the contracting officers approval. The top overhang shall be 12.7 mm maximum. Overall thickness of the top and drop leaves shall be 25.4 mm. 3.1.1.2 Hinges and leaf supports. The drop leaves shall

7、be cecurelv attached to the frame or the underside of the top using _. - a piano hinges. The hinges shall be made of steel with a finish matching that of the legs. The leaf support shall also be made of steel providing strength and rigidity to the leaves when in the raised position. The supports sha

8、ll be easily operated. 3.1.2 Legs. The legs shall be a minimum of 22.2 mm square, stainless or chromium plated steel with a polished finish. The legs shall have casters a minimum of 63.5 mrn in diameter, with ball bearing swivels. The wheel tread shall have a Shore durometer D scale hardness of 35 t

9、o 50 at 21.1 degrees C. A minimum of two casters shall have brakes. The stands maybe shipped without the legs attached, provided the supporting panel structure and legs are specifically designed for this KD feature. The legs shall be capable of being assembled by laymen (office workers) within 10 mi

10、nutes using simple hand tools. Simple, illustrated assembly instructions shall be provided. The warranty provisions shall apply to the layman assembled stands. 3.1.3 Panels. The stands shall have three separate panels, two ends and one back extending from the underside ofthe top (6.3 mm gap, maximum

11、) to a minimum of 247.6 mm down the legs. The front support, if required, shall not extend below the underside of the top in excess of 44.5 mm. All exposed edges shall be formed for strength and to avoid sharp or thin edges. 3.2 Finish. The finish shall be semi-gloss baked enamel. The colors shall m

12、atch Fed. Std. No. 595 black (27040), gray (26134) and parchment (within the range delimited by 26586 and 26405). Alternatively, the manufacturer may provide his commercial black, gray, and parchment baked enamel finish subject to the contracting officers approval. . 3.3 Performance. The stand shall

13、 be capable of meeting:all of the requirements when tested in accordance with paragraphs 4.7 through 4.10 contractors name or trademark, NSN (if specified), month and year of manufacture legibly marked with permanent dark ink. The 3.4 Identification label. The label shall have the 2 Provided by IHSN

14、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-ZLZZF m 9999974 OLb38B3 377 m A-A- 2 122 F label shall be affixed to the underside of the top. It shall not be removable by hand without defacement after being affixed for 4 hours. 3.5 Workmanship. The following at

15、tributes shall be evidence of acceptable workmanship: When the drop leaves are in the raised position, the leaves are firm and at the same level as the top; the gap between the edge of the leaf and the adjacent edge of the top does not exceed 1.16 mm. When the leaves are in the dropped position, the

16、 leaves are resting tightly against the legs. The outside surface of the panels is flush with the adjacent surface of the legs. All of the fastening materials are concealed from external view. All of the edges and corners are eased and smooth. All metal surfaces are free from sharp edges and burrs.

17、The baked enamel finish is smooth, without runs, grit, wrinkles, or separation of color. The chromium plating is free of pits, stains and brush or grind marks. In general, there are no defects that may affect the serviceability, stability, rigidity, maneuverability, or appearance of the stand. Any f

18、indings contrary to any of the above shall be considered evidence of unacceptable workmanship. 4 Quality assurance provisions. 4.1 Responsibility for inspection. The contractor shall be responsible for the performance of all inspection and testing in fulfillment of all requirements specified herein.

19、 Unless otherwise specified in the contract or purchase order, contractor may use his own or any other facilities approved by the Government as suitable for the performance of inspections and tests required by this CID. The Government reserves the right to perform any or all of the inspections and/o

20、r tests set forth in this CID, as deemed necessary to provide assurance of supply conformance to prescribed requirements. the 4.2 First article requirements. The first article inspection shall be in accordance with the solicitation. 4.3 Quality conformance inspection. A sample of the finished produc

21、t shall be selected in accordance with paragraph 4.6 of this CID for quality conformance verification. The sample shall be examined to verify that the requirements referenced in sections 1, 2, and 3 have been met. Any non-conformance with the above requirements shall be considered a defect. All defe

22、cts found shall be classified as major/minor in accordance with paragraphs 4.4 and 4.5 of this CID. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2122F m 9999974 OLb388q 203 m A-A- 2 122 F 4.4 Major defects. The following conditions of non- c

23、onformance with the stated requirements of the CID shall be considered as major defects which may potentially affect the safety, functionality, durability, usability, and life of the purchased items. Reference Dimensions: Material and parts: Construction: Wo r kmanship : Ma j or Defect S Defects - H

24、eight not as specified. - Top width or depth not as specified. - Drop leaves width or depth - Thickness not as specified. - Leg square tubing dimension not as specified. - Panel dimension not as specified. - Castor dimension not as specified. - Top, leaves, legs, panels, hinges, and leaf supports no

25、t as specified. - Castors (two minimum) are not provided with brakes. - Castor tread hardness not as specified. - The top overhang exceeds 12.7 mm. - The panels are not positioned as specified. - The drop leaves are not attached as specified. - The drop leaves are not supported as specified. - Casto

26、rs are not firmly attached to legs. - Panel construction is weak, allows for thin oz: sharp edges. - Leaves, when raised, are not level with the top not horizontal, or separated from the top by a gap _ greater than 1.16 mm. - Leaves are not fim, or not resting in a vertical position against the legs

27、 when in a dropped position. Identification - Not as specified, missing, mutilate, or Perf ormance : Label : illegible. - The stand failed the chromium plating test requirements of the CID. - The.stand failed the leaf levelness and support test. - The stand failed the service test requirements of th

28、e CID. Any of the above found by inspection shall be considered grounds for rejection. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-ZL22F 9997974 OLb35 L4T A-A-2 122 F 4.5 Minor defects. Non-conformance listed below shall be considered as mi

29、nor defects affecting the appearance of the f finished item. Minor Defects I Reference Defects Finish: - Rough or slivered surface. - Burrs. - Rough tool markings. - Oversized holes. - Pitted, stained, or blistered surfaces. - Foreign matter embedded in the finish. - Painted surfaces“c0ntain sags or

30、 runs. - Parts, components, covered with film, not free of grease, dirt, dust, epoxy, stains, etc. 4.6 Sampling for inspection. The sampling plan shall be in accordance with MIL-STD-105 with an inspection level II, Acceptable Quality Level (AQL) of 6.5 percent defective for minor defects and an insp

31、ection level of 5-2, AQL of 2.5 percent defective for major defects. Service test. A reciprocating drive device shall be attached to the top center of the stand. The attachment shall allow the stand to rotate freely on its vertical center axis. Distribute 45.3 kg evenly on the top of the stand. Plac

32、e the stand on the obstacle layout detailed in figure 1. The device shall push the stand 762 mm forward and pull it 762 mm backward over the obstacles, continuously at a rate of 10 to 15 cycles per minute for 10,000 cycles. One cycle is a forward and backward stroke. Any structural breakage, looseni

33、ng or deformation of parts which affects the stability or serviceability of the stand or any change which could cause personal injury to a user shall constitute failure of the test. 4.7 0 4.8 Test of top levelness, deflection, and rigidity. The castors shall be removed. A straight edge shall be plac

34、ed diagonally (corner to corner) across the unit top. The straight edge shall extend beyond the corners. Any warp of the top in excess of 0.78 mm is cause for rejection. This test shall be performed across both corner diagonals. Upon satisfactory completion of the above test, a weight of not less th

35、an 128.2 kg. shall be applied for at least 5 minutes to an area not to exceed 304.8 mm in diameter. The test area shall be the center of the top. The top shall not deflect more than 3.2 mm during the test. After removal of the load, no part of the stand shall have any Permanent deformation. 1 0 c 5

36、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2322F 9999974 0363886 O6 A-A-2 122 F 4.9 Levelness of leaves and test for drop leaf support. The casters shall be removed and the leaves raised to the horizontal position supported by the leaf suppo

37、rts. A straight edge shall be placed across the stand top extending to the outside edge of the leaf top. The vertical measurement from the bottom of the straight edge to the top of the outside edge of the leaf shall not be greater than 3.2 mm nor shall the leaf support hold the leaf in a position hi

38、gher than the top. The test shall be performed on both the right and left leaves. After this portion of the test is performed, a test load of 11.3 kg shall be applied to each leaf for a period of 5 minutes. The load shall be evenly distributed in the area extending from the side edge of the top to w

39、ithin 50.4 mm of the end of the leaf. Upon removal of the load and with the leaves still in the horizontal position, the measurements shall be repeated, using the straight edge. Any difference in the measurement taken before and after the load was applied in excess of 1.6 mm shall constitute failure

40、 of this part of the test. 4.10 Chromium plating test. Plated samples shall be tested for corrosion with the 5 percent neutral salt spray at 35C in accordance with ASTM Test-Method B-117. The test period shall not be less than 48 hours. After the specified exposure is completed, the specimen shall b

41、e visually examined to assure that the plating shows no evidence of peel, chip, uneven color, powder, film, pits or stain. Widely scattered spots of corrosion are permitted, however, none of these spots shall exceed 1.6 mm along the greatest dimension. 5. Regulatory requirements. The offeror/contrac

42、tor is encouraged to use recovered materials in accordance with Public Law 94-580, as amended, to the maximum extent practicable. 6. Preservation, packaging, packing, labeling, and marking. The preservation, packaging, packing, labeling, and marking shall be as specified in the contract or order. 7.

43、 Standards. The issues of ASTM B-117, MIL-STD-105 and Fed. Std. 595 in effect on the date of the solicitation shall be used to determine compliance with the stated requirements. 8. Notes. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2L22F =

44、9999974 03b3887 TL2 - I 7110-00-601-9849 Parchment I 7110-01-136-1563 Gray I A-A- 2 122 F 8.2 Military standards. Copies of MIL-STD-105 are available from the. Commanding Officer, Naval Publications and Forms Center, ? 5801 Tabor Avenue, Philadelphia, PA 19120. 8.3 ASTM standards. Copies of ASTM B-1

45、17 are available from 8.4 Federal standards. Federal Standard No. 595 is available the American Society for Testing and Materials. from the General Services Administration Business Service Centers in Boston, MA; New York, NY; Philadelphia, PA; Washington, DC; Atlanta, GA; Chicago, IL; Kansas City, M

46、O; Fort Worth, TX; Houston, TX; Denver, CO; San Francisco, CA; Los Angeles, CA; and Seattle, WA. 8 8.5 Color panel. A sample panel of the baked enamel finish is available from the Business Service Center, General Services Administration, Federal Supply Service, Washington, DC 20407 or the Business S

47、ervice Center in the nearest General Services Administration Regional office. 8.6 Plastic laminate panel. A sample panel of the decorative plastic laminate sheet is available from the General Services Administration, Federal Supply Service, Furniture Commodity Center, Engineering Division, Washingto

48、n, DC 20406. 8.7 National stock numbers. The NSNs are as follows: TYPE I NSN I COLOR I 17110-00-601-9835 I Black i I PREPARING ACTIVITY GSA - FSS/3FNE . 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2122F FEiSTACLE DETAIL MATERIAL - COLD-ROLLED STEEL E- OF TRAVEL B 1/4 in 210 nml -17 in I432 ml -4- k 30 m 762 nnl STROKE LENGTH 1 - 10 n LP54 nnl I 12 m C305 nnl I OBSTACLE LAYOUT Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-