GSA A-A-2511 A-2002 BRUSHES WIRE ROTARY CUP CRIMPED WIRE《转杯脆性钢丝刷》.pdf

1、,1,., PE.MN_JA-A-2511AMav 16,2002SUPERSEDINGA-A-251 1April 1, 1987COMMERCIAL ITEM DESCRIPTIONBRUSHES, WIRE, ROTARY,CUP, CRIMPED WIREThe General Services Administration has authorized the use of this Commercial ItemDescription by all federal agencies.1. SCOPE. This Commercisd Item Description covers

2、brushes for use with pneumatic or electric tools inthe light duty removal of rust, scale, paint, or burrs ffom all types of metal surfaces.2. CLASSIFICATION. Unless otherwise specified brushes shall conform to the following types dclasses.2.1 Brass.Class 1. Threaded arbor.Class 2. Unthreaded hole.2.

3、2 Type IL Stainless steel.*Class 1. Threaded arbor.Class 2. Unthreaded hole.2.3 Tvoe III. High-cmbon tempered steel.Class 1, Threaded arbor.Class 2. Unthreaded hole.Crimped wire, cup brush.Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other datathat may imp

4、rove this document should be sent to: General Services Administration, Federal SupplyService, Hardware SuperStore, 6FEE. 1500 Bannister Rd., Bldg.# 6, Kansas City, Missouri 64131.FSC 5130Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-25 11A 13.

5、SALIENT CHARACTERISTICS.3.1 Desirm. The brushes shall be of the cup shaped design, and for use with pneumatic or electric portable a71grinders.3.1.1 The body shall be of steel overall and constructed in such a manner as to insure an evendistribution of the wire throughout the brush to provide good b

6、alance for minimal vibration at max ratedfree speed R.P.M. Provisions shall be made for securely holding the fill wire in place and to prevent thewire from detaching due to flex during use or at rated free speed RPM. Where welded construction isused, the wire shall not be burned, broken, or affected

7、 in any way by the welding process.3.1.2- As specified the brush shall either possess a threaded arbor or an unthreaded through hole ofspecified size to fit a mandrel. The threaded arbor shall have a 5/8-11 NC female thread in accordancewith the current version of Federal Standard HZ8. To minimize v

8、ibration the threaded arbor shall bemounted to the body in a manner that when brush is installed on a “ dimensional-crimps per inch ofspecified diameter and wire points (wire-density).3.2 Identification markiruz. The tool shall be marked with the Maximum Safe Free Speed, (RPM orMSFS), the words “Wea

9、r Eye Protection”, the manufacturers name or identifying symbol and the state orcountry of manufacture, unless otherwise specified. All identification. markings shall be etched, engraved,molded, or indented directly on the items surface in such a manner that it remains clearly legiblethroughout the

10、life of the item, a713.3 Workrnanshiu. Details of workmanship shall be in accordance with the best commercial practices.Paints, coatings, plating, and finishes shall be smo?th, adherent, continuous and not stained or discolored.External surfaces shall be free of tool and gouge marks, nicks, or other

11、 surface imperfections. The itemshall be free from manufacturing workmanship defects (e.g. sharp or rough extemai edges, comers, orsurfaces) and material workmanship defects (e.g. pits, rips, tins, burrs, tears, nodules, cracks, or blisters),which may adversely impact the items serviceability, durab

12、ility, safety, or appearance.4. REGULATORY REQUIREMENTS.4.1 Recovered materials. The supplies/manufacturer is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation(FAR).4.2 Metric Products. Products manufactu

13、red to metric dimensions will be considered on an equal basiswith those manufactured using inch-pound units, provided they fall within the tolerances specified (usingconversion tables contained in the latest revision of Federal Standard 376) and all other requirements ofthk document are met. If a pr

14、oduct is manufactured to metric dimensions and those dimensions exceedthe tolerances specified in the inch- pod units, a request should be made to the contracting officer todetermine if the product is acceptable.5. PRODUCT CONFORMANCE.5.1 S The brushes shall comply with American National Standards I

15、nstitute (ANSI) standardB 165.1-1991, Safety Requirements for the design, Care and Use of Power Driven Brushing Tools. a712Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-25 11A5.2 Product Conformance. The products provided shall meet the salient

16、 characteristics of this CommercialItem Description, conform to the suppliers own drawings, specifications, standards and quality assurancepractices, and the same product and offered for sale in the commercial market. The government reservesthe right to require proof of such conformance.5.3 Responsi

17、bility for inspection. Unless otherwise specified, the supplier is responsible for theperformance of all inspection requirements and may use any commercial facilities (including thesuppliers own facilities) suitable for performance of the inspection requirements, unless disapproved bythe Government.

18、 The Government reserves the right to perform any inspections deemed necessary toassure the item conforms to the specified requirements.6. PACKAGING. Requirements of preservation, packing, packaging, and marking of packages shall be asspecified in the contract or order.7. NOTES. (This section contai

19、ns information of a general or explanatory nature that is not mandatory.)7.1 Addresses for obtainirw copies of referenced documents:Federal Acquisition Regulation (FAR): Governinent Printing OffIce, Superintendent of Documents,Washhon, DC 20401-9371GSA Specification Section (3FP-E), Suite 8100,470 L

20、Enfant Plaza, SW, Washington, DC, 20407.American National Standards Institute (ANSI), Washington, DC Headquarters, 1819 L Street, NW, 6thFL, Washington, DC, 200367.2 Nationrd Stock Numbers (NSNS). The following NSNS list correspond to the types and classesspecified in this CID. This list may not be

21、indicative of all possible NSNS associated with thk CID.Brush WireDiameter diameter. Wire fill Trim - Arbor hole Wire point -&l& m m !S.!XQ WI& Q!dXS) size. (inches) &5130-00-278-6634 HI 1 4 0.0204 Crimped .875- 1.500 5/8-1 I I 18505130-00-293-2858 m 1 15 0.0204 Crimped I-1.625 5/8-1 1 35005130-00-2

22、03-4914 m 1 16 0.014 Crimped I 1-1.750 5/8-1 1 I 42005130-00-278-0821 m 1 16 0.035 Crimped I 1-1.750 5/8- 1I I 7005130-00-705-5974 11 2 12 0.0118 Crimped I0.125-.375 318 25005130-00-455-5418 m I 2.75 0.009 I Crimped 0.875 5/8-1 1 38005130-00-278-1263 m I 14 I 0.014 I Crimped I I-I.500 5/8- I I 400(3

23、Max RPM60005500500050007000600060007.3 Orderirw data. The contract order should specify the following (in inches):(A) Title, number, and date of Commercial Item Description.(B) Type and class.(C) Brush outside diameter.(D) Wire diameter.(E) Wire point minimum. (Wire density)(F) Arbor hole size. (Thr

24、eaded or unthreaded.)(G) Wire trim-length.(H) Max RPM. (Free-speed)(I) Preservation, packing, and packaging of brushes required.3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-25 11A7.4 Key words. Crimped wire cup brushes.MILITARY INTERESTS:NONE: DoD has no registered interestin revisions and amendments to thisCommercial Description until further notice.Preparing Activity: a71GSA - FSSm4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-