GSA A-A-2513 A-2002 BRUSHES WIRE ROTARY END ATTACHMENT SOLID WIRE FILLED《单线填充端接附件转杯钢丝刷》.pdf

1、EEEElA-A-2513AMav 16,2002SUPERSEDINGA-A-2513April 1, 1987COMMERCIAL ITEM DESCRIPTIONBRUSHES, WIRE, ROTARY,END ATTACHMENT, SOLID WIRE FILLEDThe General Services Administration has authorized the use of this Commercial ItemDescription by all federal agencies.1. SCOPE. This Commercial Item Description

2、covers brushes for.use with pneumatic or electric tools inthe removal of rust, scale, paint, or burrs from small or confhred areas of all types of metal surfaces.2. CLASSIFICATION. Unless otherwise specified brushes shall conform to the following types.2.1 Brass.2.2 =. Stainless Steel.2.3 Tvpe 111.H

3、igh carbon tempered steel.End attachment brush.3. SALIENT CHARACTERISTICS.3.1 Desi.en. Solid tilled bmsh with crimped wire extending parallel to 1/4 arbor shatl, filled to the centerof the brush.3.1.1 The body shall be of specified diameter and steel overall. Construction shall be in such amanner as

4、 to insure even distribution of the wire throughout the brush to provide a balanced unit forminimal vibration at maximum safe free speed. Provisions shall be made for securely holding the tillwires in place to prevent the wire from detachkg due to flex during use or at maximum safe free speed.3,1.2-

5、 The brush shall possess a round arbor shaft 1/4 inch in diameter and of steel. To minimizevibration the”arbor shall be referenced to the body in a manner that allows the brush to run true while inuse.Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data

6、that may improve this document should be sent to: General Services Administration, Federal SupplyService, Hardware SuperStore. 6FEE, 1500 Barr dimensional-crimps per inch ofspecified diameter and wire points (wire-density). Where welded construction is used, the wire shall notbe burned, broken, or a

7、ffected in any way by the welding process.3.2 Identification markirw. The tool shall be marked with the Maximum Safe Free Speed, (RPM orMSFS), and the words “Wear Eye Protection”, the manufacturers name or identifying symbol and thestate or country of manufacture, unless otherwise specified. All ide

8、ntification markings shall be etched,engraved, molded, or indented directly on the items surface in such a manner that it remains clearlylegible throughout the life of the item.3.3 Workmanship. Details of workmanship shall be in accordance with the best commercial practices.Paints, coatings, plating

9、, and finishes shall be smooth, adherent, continuous and not stained or discolored.External surfkces shall be free of tool and gouge marks, nicks, or other surface imperfections. The itemshall be free from manufacturing workmanship defects (e.g. sharp or rough external edges, comers, orsurfaces) and

10、 material workmanship defects (e.g. pits, rips, tins, burrs, tears, nodules, cracks, or blisters),which may adversely impact the items serviceability, durability, safety, or appearance.4. REGULATORY REQUIREMENTS.4.1 Recovered materials. The supplier/manufacturer is encouraged to use recovered materi

11、als to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation(FAR).4.2 Metric uroducts. Products manufactured to metric dimensions will be considered on an equal basiswith those manufactured using inch-pound units, provided they fall within the toler

12、ances specified (usingconversion tables contained in the latest revision of Federal Standard 376) and all other requirements ofthis document are met. If a product is manufactured to metric dimensions rmd those dimensions exceedthe tolerances specified in the inch- pound units, a request should be ma

13、de to the contracting officer todetermine if the product is acceptable.5. PRODUCT CONFORMANCE.5.1- The brushes shall comply with American National Standards Institute (ANSI) standardB 165.1, Safety Requirements for the design, Care and Use of Power Driven Brushing Tools.5.2 Product Conformance. The

14、products provided shall meet the salient characteristics of thk CommercialItem Description, conform to the suppliers own drawings, specifications, standards and quality assurancepractices, and the same product and offered for sale in the commercial market. The government reservesthe right to require

15、 proof of such conformance.5.3 Responsibility for inspection. Unless otherwise specified, the supplier is responsible for theperformance of all inspection requirements and may use any commercial facilities (including thesuppliers own facilities) suitable for performance of the inspection requirement

16、s, unless disapproved bythe Government. The Government reserves the right to perform any inspections deemed necessary toassure the item conforms to the specified requirement.6. PACKAGING. Requirements of preservation, packhg, packaging, and marking of packages shall be asspecified in the contract or

17、 order.2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-/-.ia71*7. NOTES,A-A-25 13A(This section contains information of a general or explanatory nature that is not mandatory.)7.1 Addresses for obtaining couies of referenced documents:Federal Acquisi

18、tion Regulation (FAR): Government Printing Office, Superintendent of Documents,Washinon, DC 20401-9371GSA Specification Section (3 FP-E), Suite 8100,470 LErifant Plaza, SW, Washington, DC, 20407American National Standards Institute (ANSI), Washington, DC Headquarters, 1819 L Street. NW, 6thF1., Wash

19、ington, DC, 200367.2 National Stock Numbers (N SNS). The following NSN list corresponds to the types specified in thisCID This list may not be indicative of all possible NSNS associated with this CID.Rotary wheel wire brush.Wire Arbor I Wirerrim length I Max iafeI NationalStock Outsidebmsh diameter.

20、 diarrreter (inch) freespeed.Numbers TJQe diameter M u, m (!w! .f.KEM IV-l YY-0046 I U I 1. I .UUY4 I 1/40-263-0235 I III 1. .0204 i14O-456-5483 111 1. .014 I140-539-7762 111 1. .006 1/4JIXJ-UI-015-3971 III 1/2 .0204 1/4 I 5/4- 1 1/5 I l,uuu5130-00-293-2410 111 314 .0204 I14 3/4-1 1/8 8,000-5130-00-

21、435-2309 111 314 .006 114 3/4- 1 1/8 I 8,OOO7.3 Ordenn data. The contract order should specify the following (in inches):(A) Title, number, and date of Commercial Item Description.(B) Type.(C) Brush outside diameter. (0. D.)(D) Wire diameter.(E) Wire trim-length,(F) Max RPM. (Free-speed)(G) Preserva

22、tion, packing, packaging, and marking of brushes, required,7.4 Kev words. End attachment wire brushes. .MILITARY INTERESTS:NONE: DoD has no registered interestin revisions and amendments to thisCommercial Description until furthernotice.Preparing Activity:GSA - FSS3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-