GSA A-A-50390 A-1996 SHIRT DISPOSABLE《一次性衬衫》.pdf

1、- A-A-50390A 9 9999974 0172YbY BT2 I INCH-POUND I January 23 , 1996 A-A-50390A COMMERCIAL ITEM DESCRIPTION SHIRT, DISPOSABLE The General Services Administration has authorized the use of this commercial item description. 1. The shirt is intended for use as part of an ensemble used to protect torpedo

2、 handlers from exposure to Otto fuels. SCOPE. This commercial item description covers the requirements for a disposable shirt. 2. SALIENT CHARACTERISTICS 2.1 DescriDtion. The shirt shall be below-the-hip length style, and have full-length, set-in one or two piece sleeves, a sewn-on collar and a full

3、 front opening secured by 5 plastic snap fasteners. 2.2 Material. The material for the collar, front, and sleeves shall be a white polyethylene coated spun bonded olefin conforming to the requirements for type II of Table I. The coated side of the material is considered to be the face side. The mate

4、rial for the back shall be an uncoated spun bonded olefin conforming to the requirements for type I of Table I. The stitching thread and the plastic snap fasteners shall be of any commercial type suitable for the purpose intended. The color of the thread shall be natural or white. The of the snap fa

5、steners shall be white. IBeneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document shouid be sent to: Defense Personnel Support Cent distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted wit

6、hout license from IHS-,-,-A-A-50390A Y Ol1724b5 739 W A-A-50390A Tolerances: +1 TABLE I. - Material requirements. Sizes X-Small Small Medium Large X-Large XX-Large ASTM-D5034 ASTM-D 1424 - 1/ The coated side shall be exposed to the water. - 2/ Procedure A - Pressure application by Mullen type Hydros

7、tatic Tester, sections 34-37, Procedure 1 (except that the rate of displacement shall be as specified in section 34.2) shall be used. A Chest 20-1/2 21-1/2 23-1/2 25-112 27-1/2 28-1/2 2.3 Sizes and measurements. The finished shirt shall conform to the measurements in Table II. Table II. Finished mea

8、surements (in inches) B Inseam Sleeve Length 22- 1 /4 22- 1/4 22-518 23-118 23-112 23-718 + 112, - 3/8 C Outer Back Length 29- 1 /2 30 31 32 30-1/2 31-1/2 + 1/2, - 3/8 2.4 Pattern. The Government shall furnish a single size pattern. The contractor is - responsible for grading patterns for additional

9、 sizes. The Government patterns shall be used to make the contractors working patterns. The Government patterns shall not be altered in any way. The working patterns may be modified to accommodate automation; however, if the working patterns are modified the design and measurements must be maintaine

10、d as intended by Government patterns. Commercial patterns may be used in lieu of Government patterns provided they are approved for used by the Government and conform to the cited design and finished measurements. 2.5 Labels. A commercial-type label is acceptable, provided that an additional label c

11、ontaining the contractors name, contract number, size and National Stock Number (NSN), and cautionary statement is placed directly on the shirt by printing, stamping, stenciling or printed on 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5039

12、0A H 7777774 OL72Ybb b75 W A-A-50390A a sensitive label that adhere to the inside of the garment. The cautionary statement shall be printed in larger letters than all other lettering on the label and shall read: CAUTION: THIS GARMENT SHALL NOT BE REUSED AND MUST BE DISCARDED WHEN QTTO FUEL STAINS AR

13、E OBSERVED 2.6 Labelhag. Each item shall be individually bar-coded with a paper tag for personal clothing items. The paper tag shall be standard bleached sulfate having a basis weight of 100 pounds. The paper used for the tags shall have a smooth finish to accept thermal transfer and direct printing

14、. The tags shall have a hole and shall be attached to each item by a fastener, clearly legible and readable by a scanner. The bar coding element shall be a 13 digit national stock number (NSN). The bar code type shall be a medium to high code density and shall be located so that it is completely vis

15、ible on the item when it is folded andor packaged as specified and so that it causes no damage to the item. 3. recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). REGULATORY REQUIREMENTS. The offerorkontractor is enc

16、ouraged to use 4. QUALITY ASSURANCE PROVISIONS 4.1 Certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this commercial item description and conforms to the producers own drawings, specifications, standards, an

17、d quality assurance practices. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 4.2 Market acceptance criteria. The item offered, or a generic equivalent, must have

18、 been sold to the commercial market or to the Government for at least two years. 4.3 Warranty. The item offered shall include the standard warranty given to the Commercial market beginning with the date of delivery of the individual items. 4.4 Visual examination. Each shirt shall be examined for the

19、 defects listed below: Defects. Any hole, cut, or tear; color not as specified; any part shaded; any spot or stain (outside); raw edges, open seams, thread ends not removed, or loose tension resulting in loose seams; any material defects, distorted parts or poor workmanship; any component part omitt

20、ed; label missing, incorrect, or illegible; measurement of item not as specified; bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item; bar code causes damage to the item; any items not packaged in accord

21、ance with the contract or purchase order. 5. Preservation, packing, and marking. The preservation, packing, and marking shall be as specified in the contract or order. 6. NOTES 6.1 Source of Government documents. Copies of military and Federal documents are available from: 3 Provided by IHSNot for R

22、esaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50390A 9999974 0372467 501 = A-A-5039OA I Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19 1 1 1-5094 6.2 Source of non-Government documents ASTM Test Methods (Applications for copies sh

23、ould be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1 187,) AATCC Test Method (Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215.) MILlTARY

24、INTERESTS: Custodians Navy - NU Review Activities Navy - SH, OS CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY: DLA - CT Project 84 15-0063 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50390A 9999974 OL724bB 448 A-A-5039OA

25、BACK FIGURE 1 - SHIRT DISPOSABLE A. Chest - Measure across the chest at the base of the armhole from folded edge to folded edge. B. Sleeve inseam - Measure along inseam from armhole to bottom of sleeve. C. Length - Measure along center back from lower edge of neckline to bottom of shirt. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-