GSA AA-R-0020 B-1972 RACK DISPLAY BOOK (WOOD)《书陈列架(木制)》.pdf

1、AA-R-0020B 71 W 7777774 0023553 4 W January 7, 1972 INTERIM RFVISION OF Fed. Spec. AA-R-20A JY 1, 1959 INTERIM FEDERAL SPECIFICATION RACK, DISPLAY , BOOK, (WOOD) This Interim Federal Specification was developed by the Standardization Division, Federal Supply Service, General Services Administration,

2、 Washington, D. C., 20406, based upon currently available technical information. It is recommended that Federal agencies use it in procurement and forward recommendations for changes to the preparing activity at the address shown above. The General Services Administration has authorized the use of t

3、his Interim Federal Specification as a valid exception to Federal Specification AA-R-20a1 dated July 1, 1959. 1. SCOPE 1.1 Scope. This specification covers one type of book display rack fabricated of wood foreneral office use. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effec

4、t on the date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: Federal Specifications: FF-S-111 - Screw, Wood. TT-L-57 - Lacquer, Rubbing, Clear, (For Wood Furniture). PPP-B-636 - BOX, Fiberboard. PPP-C-843 - Cushioning Material, Cellu

5、losic. Fed. Std. No. 123 - Marking for Domestic Shipment (Civil Agencies). cations, Standards, and Handbooks as outlined under General Information in the Index of Federal Specifications and Standards and at the prices indicated in the Index. The Index, which includes cumulative monthly supplements a

6、s issued, is for sale on a subscription basis by the Superintendent of Documents, U. S. Government Printing Office, Washington, D. C. 20402. (Single copies of this specification and other Fe-dera1 Specificationa required by activities outside the Federal Government for bidding purposes are available

7、 without charge from Business Service Center8 at the General Services Administration Regional Offices in Boston, New York, Washington, E, Atlanta, Chicago, Kansas City, MO, Fort Worth, Dcnver, San Franciaco, Los Angehe, and Seattle, WA. (Federal Government activities may obtain copies of Federal Spe

8、cifications, Standards, and Handbooks and the Index of Federal Specifications and Standards from established distribution points in their agencies). Federal Standards: (Activities outside the Federal Government may obtain copies of Federal Specifi- FSC 7110 THIS DOCUMENT CONTAINS 13 PAGES. Provided

9、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA-R-0020B 71 W 7777774 0021552 b W AA-R- O O 2 OB (GSA-FSS ) Eilitary Standards MIL-CTD-105 - Sampling Procedures and Tables for Inspection by Attributes. MIL-STD-129 - Marking for Shipment and Storage. (Copies

10、 of Military Specifications and Standards required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer). 2.2 Other publications. The following documents form a part of this specifi- cation to the ex

11、tent specified herein. Unless a specific issue is identified, the issue in effect on date of invitation for bids or request for proposal shall apply. National Motor Freight Traffic Association, Incorporated, Agent: National Motor Freight Classification. (Application for copies should be addressed to

12、 the American Trucking Association Inc., Tariff Order Section, 1616 P Street, N.W., Washington, D.C. 20036.) Uniform Classification Committee, Agent: Uniform Freight Classification. (Application for copies should be addressed to the Uniform Classification American Society for Testing and Materials (

13、ASTM) Standard: Committee, Room 202 Union Station, 516 W. Jackson Blvd., Chicago, IL 60606.) ASTM D 905 - Standard Method of Test for Strength Properties of Adhesives in Shear by Compression Loading. (Copies may be obtained upon application to American Society for Testing and Materials, 1916 Race St

14、reet, Philadelphia, Pennsylvania 19103). 3. REQUIREMENTS 3.1 Preproduction sample. Unless otherwise swecified (see 6.2), before production is commenced, a sample of the finished item and each component wart conforming to the requirements of this specification shall be offered for approval of the con

15、tracting officer or his authorized representative. Approval of the preproduction sample authorizes the commencement of production, but does not relieve the contractor of responsibility from compliance with all other applicable provisions of this specif i ca tion. 3.2 Materials. The materials used in

16、 construction of the rack shall be of the kind and quality specified herein. 3.2.1 Adhesives. The adhesives to be used shall be any adhesive that will develop an average block shear strength of not less than 2,800 pounds per square inch when tested as specified in 4.3.1.1. 3.2.2 Solid wood. 3.2.2.1

17、Varieties. The varieties of wood used in the construction of the book display rack shall be one of the following species: beech, birch, cherry, maple, pecan, walnut, hickory, and mahogany (American and African only). i 2 . Provided by IHSNot for ResaleNo reproduction or networking permitted without

18、license from IHS-,-,-splits; shake and other defects which will affect its serviceability or strength. A few small burls, pin-knots averaging not more than two per square foot, mineral streaks a maximum of 1/16 inch by 4 inches, or 1/8 inch by 2 inches in area and averaging not more than one per squ

19、are foot, will be permitted. 3.2.2.3 Seasoning. All wood parts shall be uniformly kiln dried to a moisture content of 5 to 8 percent and shall be stored in properly controlled atmosphere to I ci. assure uniform distribution and stresses that impair serviceability or finished appearance; I *- 3.2.3 F

20、inishins materials. not cause failure to finish panels in tests specified in 4.3.1.1, 3.2.3.2 Stain. The stain shall consist of an organic dye in an organic solvent and shall not cause failure to finish panels in ultraviolet resistance test specified in 4.3.1.1. 3.2.3.3 Lacquer. The lacquer shall co

21、nform to the applicable requirements of 3.2.4 Hardware. type I or type II of TT-L-57 when tested as specified in 4.3.1.1. face (in contact with floor: rubber cushion shall be hiqhly polished stainless steel or bkown hiqh impact plastic in the size and type specified. 3.3 Constr-uction. 3.3.1 Design.

22、 The design of the book display rack shall be as shown in Figures 1 and 2. The overall dimensions of the book rack shall be 22 inches wide by 12 inches deep by 30 inches high, excluding glides. The-ok display rack shall provide two areas for accommodating books. othemrise specified herein : 3.3.2.1

23、Overall tolerances for book display rack: (a) Height - plus 1/4 inch minus 1/8 inch. (b) Depth - plus 1/4 inch minus 1/8 inch. (c) Width - plus 1/4 inch minus 1/8 inch. (a) Dimension of any solid wood part (width and thickness) - plus 1/16 inch until.the adhesive-has properly-set. the joint while ad

24、hesive is setting. Starved or Insufficiently glued joints will not be acceptable. Nails o; brads shall not be used for holding Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA-R-OOZOB(GSA-FSS) 3.3.4 Details of construction. The principal component

25、parts of the book display racks shall be end panels, trough members and base reinforcement strips. The end panels and trough members shall be made of full length strips of solid wood, specified in 3.2.2, not greater than 6 inches or less than 2 inches wide, except that one edge strip may be not less

26、 than 1 inch wide. be carefully selected for similar grain and color and shall be edge joined with continuous tongue and groove construction. Alternatively, matched square edge joints may be used for the end panels. members shall be 13/16 inch, minimum. The trough members shall be joined together by

27、 tongue and groove and shall be tenoned on the ends to fit the mortises on the end panels. All pieces shall be securely glued using adhesives, specified in 3.2.1. The base reinforcement strip shall be of one piece of solid wood, specified in 3.2.2, and shall be 3/4 inch thick by 2 inches wide, minim

28、um, A base reinforcernent strip shall be securely glued to the bottom inside face of each end panel, In addition, it shall be secured by countersunk screws (No. 10 size, minimum), specified in 3.2.4.2. The screws shall be positioned as shown in Figure 2. All exposed corners and edges shall be eased

29、with the exception of the top corners of the end panels and the top edge of the base reinforcement strips which shall be rounded to a radius of approximately 1/2 inch. The grain pattern of all component parts shall run the long direction of the part. The solid wood strips shall The thickness of the

30、end panels and trough 3.3.5 Method of finishing wood surfaces. The wood surfaces shall be finished 3.3.5.1 Exposed wood surfaces. All wood surfaces normally exposed to view shall be finish sanded smooth and all corners and edges eased, thoroughly cleaned, and finished as follows: 1. Sap stain to equ

31、alize color. 2. Apply selected colorant to produce color specified. Stain, specified in 3.2.3.2, and colorant shall conform to tests specified in 4.3.1.1. 3. Wash coat with adhesive sealer. Sealer shall withstand toughness and adhesion test specified in 4.3.1.1 without whitening or cracking. 4. Scuf

32、f sand, using sandpaper grit of fineness needed to produce proper surface. 5. Fill to degree necessary to match standard reference panel. specified in 3.2.3.1, shall conform to the test specified in 4.3.1.1. 6. Seal with adhesive type sealer. Sealer shall withstand toughness and adhesion test specif

33、ied in 4.3.1.1 without whitening or cracking. 7. Sand, using sandpaper grit of fineness needed to produce proper surface. 8.-Shade to tie-in color variation, if necessary. Shading shall conform to the test specified in 4.3.1.1. 9. Top coat with lacquer (2 coats). The lacquer, specified in 3.2.3.3, a

34、nd finish shall be of a quality to meet the requirements specified in 4.3.1.1. The filler, NOTE: The natural grain of the wood shall not be clouded by the finishing materials. Bleaching agents or materials shall not be used. The application of materials, drying time, sanding, cleaning and rubbing sh

35、all be controlled to produce items of smooth, uniform exposed surfaces without blisters, pits, wrinkles, runs, tackiness or more than a trace of orange peel. 3.3.5.2 Unexposed surfaces. Operation number 8 may be performed where shown or after operation number 5. The bottom edge of the end panels and

36、 base reinforcement strip shall be machined smooth and cleaned and stained a uniform walnut color. A coat of adhesive sealer shall be applied. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA-R-0020B 72 W 799997L1 0023555 3 panel- adopted by Federa

37、l Supply Service, General Services Administration for color, appearance, and gloss (see 6.3). Stck Number, contract number, date-of manufacture of this specification .* Where specific requirements are not given , good commercial practice of the contract furniture industry shall be used. Book display

38、 racks shall conform to the level of quality established herein. 1 4. QUALITY ASSURANCE PROVISIONS 4.1 General quality assurance provisions. 4.1.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspe

39、ction requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are

40、deemed necessary to assure that supplies and services conform to prescribed requirements. 4.1.2 Government verification. All quality assurance operations performed by the contractor shall be subject0 Government verification at unscheduled intervals. Verification shall consist of surveillance of the

41、operations to determine whether the practices, methods, and procedures of the written inspection plan are being properly applied, and Government product inspection, to measure quality of product offered for acceptance. Deviation from the prescribed or agreed-upon procedures, or instances of poor pra

42、ctices that might have an effect on the quality of the product will be immediately called to the attention of the contractor. Failure of the contractor to promptly correct the deficiencies discovered shall be cause for suspension of acceptance until the correction has been made or until conformance

43、of product to prescribed criteria has been demonstrated. To avoid interference with operations, the contractor shall designate a responsible official, OP officials, to whom the Government inspector will report such instances. the completely fabricated item for all provisions of this specification. 4

44、.2 Preproduction sample inspection. Examination and testing shall be made on 4.3 Sampling for inspection and acceptance. Sampling and inspection shall be performed in accordance with the provisions set forth in MIL-STD-105, except where otherwise indicated hereinafter. 4.3.1 Inspection of materials

45、and components. In accordance with 4.1, the supplier is responsible for insuring that materials and Components used were manufactured, tested, and inspected in accordance with the requirements of referenced subsidiary specifications and standards to the extent specified, or if none, in accordance wi

46、th this specification. provision of the subsidiary specification, testing of the components shall be performed in accordance with table I for the characteristics shown therein. values specified in section 3 of this specification apply to the average determin- ations made on a sample unit for test pu

47、Kposes as specified in the applicable test method. When the sample size for components covered by the subsidiary specifications is not specified, the sample size for each characteristic shall be in accordance with inspection level S-2 of MIL-STD-105 except that for lot sizes of 501 (units of product

48、s) and over the sample size shall be 5. The lot shall be unacceptable if one or more sample units fail to meet any of the requirements specified. 4.3.1.1 Testing of components. In addition to the quality assurance testing The a 5 Provided by IHSNot for ResaleNo reproduction or networking permitted w

49、ithout license from IHS-,-,-AA-R-0020B (GSA-FSS) TABLE I. Instructions for testing components and materials Requirement Sample Component Characteristic Reference Test Method Unit Adhesive Block shear test 3.2.1 ASTM 905 i.e., end item rocks more than 1/16 inch when placed on flat surface. X Glide missing. X Glide not as specified. X Glide improperly positioned. X Glide not secured properly. X ion Text incomplete. X Missing, incorrect or illegible. X Marking in wrong location. X 4.3.2.3