GSA FF-L-2937-2005 COMBINATION LOCK MECHANICAL《机械暗码锁》.pdf

1、INCH-POUNDFF-L-2937Januarv 31,2005FEDERAL SPECIFICATIONCOMBINATION LOCK, MECHANICALThe General Services Administration has authorized the use of this federalspecification by all Federal agencies.1. SCOPE AND CLASSIFICATION1.1- This specification covers commercially available combination locks. The l

2、ockshall be a dial operated, mechanical, bolt type lock that uses a three number combinationwith standard-left-right left dialing sequence.1.2 Classification. Combination locks shall be manipulation, force, and thermal resistant.The locks shall be of the following styles, as specified.K Key changeab

3、le combination lockH Hand chgeable combination locka712. APPLICABLE DOCUMENTS2.1 Government publications. The following documents, of the issues in effect on thedate of invitation for bids or request for proposals, forma part of this specification to theextent specified herein.Federal Standards:FED-

4、STD- 123 Marking for Shipment (Civil Agencies)(Activities outside the Federal Government may obtain copies of federal specification,standards, and commercial item descriptions as specified in the General Informationsection of the Index of Federal Specifications, Standards and Commercial ItemDescript

5、ions from the General Services Administration, Federal Supply Service,Specification Section, East 470 LEnfant Plaza SW, Suite 8100, Washington, DC 20407.)Beneficial comments, recommendations, additions, deletions, clarifications, etc., and anyother data which may improve this document should be sent

6、 to: General ServicesAdministration, National Furniture Center, Engineering Division (3 FNE-CO), 1901 SouthBell Street, Room 403, Arlington, VA 22202.FSC 5340Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-L-2937(Singie copies of this specificatio

7、n and other federal specifications required by activitiesoutside the Federal Government for bidding purposes are available without charge fromBusiness Service Centers at the General Services Administration Regional Offices inBoston, New York, Washington, DC, Atlanta, Chicago, Kansas City, MO, Fort W

8、orth,Denver, San Francisco, Los Angeles, and Seattle.(Federal government activities may obtain copies of federal standardization documentsand Handbooks and the Index of Federal Specifications, Standards and Commercial ItemDescriptions from the established distribution points in their agencies.)Milit

9、arv Standards:MIL-STD-129 - Marking for Shipment and Storage.MIL-STD-889 Dissimilar Metals(Copies of Military Specifications and Standards required by contractors in connectionwith specific procurement functions should be obtained from the procuring activity or asdirected by the contracting officer.

10、)2.2 Other publications. The following documents form a part of thk specification to theextent specified herein. Unless a specific issue is identified, the issue in effect on the dateof invitation for bids or request for proposals shall apply.National Motor Freight Traffic Association, Inc., Agent:N

11、ational Motor Freight Classification.(Application for copies should be addressed to the American TruckingAssociation, Inc., Traffic Department, 1616 P Street, NW, Washington, DC20036)Uniform Classification Committee, Agent:Uniform Freight Classification.(Application for copies should be addressed to

12、 the UniformClassification Committee, Room 1106,222 South Riverside Plaza,Chicago, IL 60606.)Underwriters Laboratories, Inc. (UL) Publications:ANSUUL 768- Standard for Combination Locks.(Application for copies should be addressed to Underwriters Laboratory,12 Laboratory Drive, Research Triangle Park

13、, NC 27709-3995.)2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-L-2937oAmerican National Standards Institute (ANSI)/American Societv for Oualitym:ANSI/ASQ Z1.4 - Sampling Procedures and Tables for Inspection by Attributes(Application for copies

14、should be addressed to ANSI, 11 West 42nd Street,New York, NY 10036.)American Society for Testing and Materials (ASTM).:ASTM B 117-97 Standard for Salt Spray (fog) Testing(Application for copies should be addressed to the American Society forTesting and Materials, 100 Barr Harbor Drive, West Conshoh

15、ocken, PA 19428-2959)2.3 Order of precedence. In the event of a conflict between the text of this specificationand the references cited herein, the text of this specification shall take precedence.Nothing in this specification, however, shall supersede applicable laws and regulationsunless a specifi

16、c exemption is obtained.3. REQUIREMENTSa71 3.1 Ourditication. The combination locks furnished under this specification shall beproducts which have been tested, and have passed the qualification tests specified insection 4, and have been listed on or approved for listing on the applicable qualifiedpr

17、oducts list (QPL).3,1.1 Qualification suspension.3,1.1. I Development of entry techniques. The combination locks qualified under thisspecification will be continually tested by the Government during the term ofqualification to determine whether the security protection afforded by the locks should or

18、can be improved. If, at any time, entry techniques are developed within the framework ofthe specification which affect a combination locks security integrity, it shall be removedfrom the QPL and the manufacturer will be required to modify the product to the extentnecessary to defeat the techniques,

19、and have the lock requalified.3,1.1.2 Change in specification requirements. This specification will be continuallyreviewed by the Government to determine whether specification requirements should orcan be changed to improve product quality. If, at any time, requirements are changed,and such changes

20、affect the qualification status of a qualified combination lock, it shallbe removed from the QPL and the manufacturer will be required to modify the product tothe extent necessary to comply with specification changes and have the lock requalified.Provided by IHSNot for ResaleNo reproduction or netwo

21、rking permitted without license from IHS-,-,-FF-L-29373.2 m. The lock dial and ring shall be ,of top reading, spy resistant design with dialand dial ring protected by a snap-on dust cover. The case and cover dimensions shall beas shown in Figure 1. At the option of the purchaser, the lock shall be h

22、and or key a71change style (see 6.2).3.3 UL requirements. The lock shall conform to the Group 1 requirements of UL 768.The lock shall have passed the UL testing and be listed by UL. The government reservesthe right to perform any testing or inspections in UL 768.3.4 Combinations. The lock shall have

23、 a minimum of 800,000 usable combinations.The dial shall be marked with 100 graduation divisions, each 51hdivision distinctivelyidentified to facilitate easy reading. Each 10* division from Oto 90 shall be marked witha number.3.5 Dialing tolerance. A three wheel lock shall not open when the dial is

24、turned morethan % graduation on either side of the proper graduation for each wheel. The lock shallbe tested in accordance with paragraph 4.7.1.3.6 Thermal lockout. The lock shall have a thermal lockout feature which will restrictunaided retraction of the bolt when the temperature reaches 170 degree

25、s Fahrenheit. Thelock shall be tested in accordance with paragraph 4.7.2.3.7 Bolt lockout. The lock shall have a mechanical relock mechanism that will preventthe retraction of the bolt if the lock cover plate is moved more than 0.10 inch (2.54 mm)at any point from its normal operating position. The

26、lock shall be tested in accordancewith paragraph 4.7.3.3.8 Endurance test. After completion of the 10,000 cycles the lock shall undergo 50combination changes including three open and close verifications after each change. Thelock shall be tested in accordance with paragraph 4.7.4.3.9 Salt smav corro

27、sion requirement. The lock shall pass the test of 4.7.53.10 Dissimilar metals. Dissimilar metals, as defined in MIL-STD-889, must either beplated or compatible to prevent operationally destructive corrosion.3.11 Resistance to unauthorized opening. The lock shall pass the test of 4.7.7.3.12 Torque re

28、quirement. The lock shall meet the torque requirements below whentested in accordance with 4.7.8.3.12.1 Wheel-pack assembly. The wheel centers shall resist slippage when torqued to 5inch-pound-force (lbf.in) (0.575 Newton meter (N.m) in either direction.4Provided by IHSNot for ResaleNo reproduction

29、or networking permitted without license from IHS-,-,-FF-L-2937o3.12.2 Wheel to wheel center siirmage. Mount each wheel so that it remains stationary.Apply a torque of 5 lbf.in (0.575 N.m) to the wheel center (or insert) in a clockwiserotation and then a counterclockwise rotation. Any evidence of sli

30、ppage at less than therequired torque between the wheel center and the outer wheel shall constitute failure ofthk test.3.12.3 Wheel-uack assemblv tomue. The Iocks shall maintain a wheel-pack assemblytorque in the range of not less than 16 inch-ounce-force (ozf.in) (O.1136 N.m)and notmore than 24 ozf

31、.in (O.1704 N.m).3.12.4 Security. After the break-in period, the ending torque shall be checked todetermine that the lock torque is less than twice the starting value.3.13 Case and bolt strerwth. The lock shall pass the test required in paragraph 4.7.63.14 Workmanship. The workmanship shall be of a

32、quality to produce a serviceable andwell-finished end item able to withstand hard daily usage. The edges of all exposed partsshall he protected by folding, beading, flanging, or grinding to eliminate burrs,roughness, and sharp edges. Welding and brazing shall produce rigid and securecomections. Lock

33、 washers, cotter pins, clips, retainers, or built-in features shall be usedto prevent loosening of screws, bolts, and nuts, which may cause disengagement of partsand possible lockout. The locking mechanism shall operate smoothly without binding ora71 jamming of parts. The lock shall be free of any d

34、efector feature which may affect itsappearance and serviceability, or which may cause personal injmy.3.15 Assembly drawirw and Parts list. A parts list of all lock parts which maybe subjectto subsequent replacement because of wear or damage shall be furnished with each lockdelivered under contract.

35、The parts list shall clearly identify the parts by description,location and part number. When necessary, assembly drawings shall be provided to showthe location of the parts. The parts list shall be printed on heavy paper or other suitablematerial and provided with each lock.4. QUALITY ASSURANCE PRO

36、VISIONS4.1 Inspection resonsibilit. Except that testing for qualification shall be performed byan agency designated by General Services Administration, the supplier is responsible forthe performance of all inspection requirements as specified herein. Except as otherwisespecified, the supplier may ut

37、ilize his own or any other inspection faciIity or serviceacceptable to the Government. Inspection records of the examinations and tests shall bekept complete and available to the Government as specified in the contractor order. TheGovernment reserves the right to perform any of the inspections set f

38、orth in thespecification where such inspections are deemed necessary to assure that supplies andservices conform to the prescribed requirements.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-L-29374.2 Component and material inspection. The suppli

39、er is responsible for insuring thatcomponents and materials used are manufactured, tested and inspected in accordancewith the requirements of referenced subsidiary specifications and standards to the extent a71specified, or, if none, in accordance with this specification.4.3 Examination of preparati

40、on for delivery, An examination shall be made to determinethat the packaging, packing and marking comply with the requirements in Section 5 ofthk specification. Defects shall be scored in accordance with Table I. The sample unitshall be one sKlpping container folly prepared for delivery. Sampling sh

41、all be inaccordance with ASQ Z1 .4, The lot size shall be the number of containers in theinspection lot. The inspection level shall be Level I and the AQL shall be 4.0 defects perhundred units,Table I. Classification of preparation for delivery defectsExamine DefectsMarkings (exterior) Omitted; inco

42、rrect; illegible; improper size, location, sequence ormethod of application.Materials Any component missing or damaged.Workmanship Inadequate application of components such as incomplete closure ofcontainer flaps or shroud.4.4 Testing Procedures and tests.4.4.1 Testing agencv. Qualification tests ac

43、complished on locks submitted for approvalfor inclusion on the applicable Qualified Products List (QPL) and any retesting that may a71be required shall be performed by a testing agency specifically designated by the GeneralServices Administration.4.4.2 Test costs. Al testing costs entailed in determ

44、ining the qualification of thesuppliers product, including costs of retesting of a qualified product if subsequentlydisqualified under 3.1,1, shall be borne by the supplier, and shall be payable to theGeneral Services Administration. All costs associated with changes made by thesuppliers product tha

45、t require evaluation or testing shall be borne by the supplier.4.4.3 Test procedures. The following procedures shall govern the testing of all lockssubmitted for qualification under this specification:(a) Samples shall be submitted for qualification only after the supplier has obtainedwritten author

46、ization from the General Services Administration.(b) A qualification test maybe discontinued at the Governments testing facility at anytime the product fails to meet any one or more of the requirements set forth in thisspecification. The manufacturer may be permitted to make modifications on the sam

47、pleduring the testing phase where such modifications, in the judgment of the GeneralServices Administration and the testing facility, are clearly in the interest of the Gover-nment.6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-L-2937a71 (c) In

48、case of failure of the sample, consideration will be given to the request of themanufacturer for resubmission for retest only after it has been clearly shown that changeshave been made in the product which the Government considers sufficient to warrantretest.(d) The manufacturer or his representativ

49、e will not be permitted to observe the actualtamper resistance tests conducted on his product at the testing facility. However, whensamples tested fail to comply with the requirements of this specification, the sample maybe examined by the manufacturer or his representatives and full details of the failure maybe made known to them in a manner which, for reasons of security, will be in the bestinterest of the Government.4.4.3,1 Test samples.