HOLDEN HN 2377-2007 SEALER PREFORMED WELDABLE HIGH EXPANSION 100-200%《预成型密封层 可焊接 高膨胀率100-200%》.pdf

1、ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2377 1 of 6 August, 2001 September, 2007NAME: SEALER PREFORMED, WELDABLE HIGH EXPANSION 100-200% THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS TH

2、E RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:MaterialsEngineeringStandardFormsMaterialSpecificationMatspec.doc 1. SCOPE This specification details the requirements of an extruded weld through tape which will expand approximately 100-200% and cure upon heatin

3、g. The material is tacky one side, and is intended for sealing interior and exterior body joints against water, dust and air intrusion. The material must be a smooth and homogeneous mixture free of air, lumps, unmixed particles and foreign materials. Material must not contain chlorine or produce an

4、unpleasant odour upon welding. After removal of the release paper, the material must have satisfactory pressure sensitive tack and adhere to oily surfaces such as steel, zinc coated steel and galvanised metal. It must have good weatherability and must not accelerate corrosion of the substrate over w

5、hich it is applied. 2. REFERENCES ASTM D792 ASTM D5 GM9832P GM9010P GM9037P GM9640P HN 0256 HN 0214 GM9773P GM9828P GM9831P HN 1000 GM9929 3. REQUIREMENTS 3.1 Physical Properties Physical Properties Results Test Method Specific Gravity (as received) 1.2 ASTM D792 Uncured Hardness (50g load, 5s, need

6、le penetrometer) 5-15mm ASTM D5 Odour Non-toxic, Not unpleasant GM9832P ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2377 2 of 6 August, 2001 September, 2007NAME: SEALER PREFORMED, WELDABLE HIGH EXPANSION 100-200% THIS DOCUMENT

7、 MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:MaterialsEngineeringStandardFormsMaterialSpecificationMatspec.doc 3. REQUIREMENTS (continued) 3.1 Physical Properties (continued) Physical Pr

8、operties Results Test Method Toxicity Non toxic - Solids content 95% min GM9010P Water absorption 2% GM9640P Expansion 1.25mm, 20 min 170C 20 min 205C 135% 143% GM9037P 3.2 Adhesion 3.2.1 A 80mm x 150mm sealer patch will be applied to oiled (3g/m2): cold rolled steel, zinc coated steel and galvanise

9、d steel panels (100mm x 300mm) respectively. Panels will be baked for: (i) Under bake 20 min at 170C + 40 min at 140C (ii) Standard bake 30 min at 180C + 50 min at 145C (iii) Over bake 60 min at 180C + 50 min at 145C ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION

10、NUMBER SHEET RELEASE REVISION : HN 2377 3 of 6 August, 2001 September, 2007NAME: SEALER PREFORMED, WELDABLE HIGH EXPANSION 100-200% THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM

11、: I:MaterialsEngineeringStandardFormsMaterialSpecificationMatspec.doc 3. REQUIREMENTS (continued) 3.2 Adhesion (continued) 3.2.2 The sealer must not crack or lose adhesion to the oily metal steel panels during or after the following conditions: (i) Initial After cooling at ambient conditions for 24h

12、. (ii) Heat Ageing 336h 70C (iii) Humidity ( HN 0256) 168h 38C 100% R.H. (iv) Scab corrosion (HN 0214) 20 cycles (v) Cold slam (GM9773P) 10 slams -30C 3.3 Corrosion resistance After exposing panels to the scab corrosion (HN 0214) and humidity (HN 0256) cycles on oiled plain steel, zinc coated and ga

13、lvanised panels remove sealer from panels. There must not be any corrosion on the panel surface underneath the sealer. 3.4 Process Requirements 3.4.1 Smoke (GM9828P) The sealer must not smoke up to 177C with slight smoke allowed up to 191C. 3.4.2 Blocking Sealant material as packaged must not stick

14、together when stacked one on top of another after 3 days at 54C with a 500g load. ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2377 4 of 6 August, 2001 September, 2007NAME: SEALER PREFORMED, WELDABLE HIGH EXPANSION 100-200% THI

15、S DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:MaterialsEngineeringStandardFormsMaterialSpecificationMatspec.doc 3. REQUIREMENTS (continued) 3.4 Process Requirements (continued)

16、3.4.3 Weldability (GM9929). Must pass 750 welds. Sealer thickness 1.0-1.5mm. 3.4.4 Flame resistance (GM9831P) Must resist 50 passes with an open flame. The material must be self extinguishing. 3.5 Stability Requirements 3.5.1 Elevated Temperature Stability As shipped, the laminate shall be capable o

17、f withstanding a temperature of 55 C for a period of 72 hours without cold flowing or blocking or laminate separation. 3.5.2 Low Temperature Stability As shipped, the laminate shall be capable of withstanding a temperature of 10 C for a period of 72 hours without cracking or laminate delamination. 3

18、.5.3 Storage Stability As shipped, the shelf life of the material shall be 60 days at a temperature of 35 C. The shelf life of the material shall commence upon receipt of the material from the manufacturer. NOTE: Material conditioned in the above environments (3.4.1, 3.4.2 & 3.4.3) shall meet all re

19、quirements of this specification. ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2377 5 of 6 August, 2001 September, 2007NAME: SEALER PREFORMED, WELDABLE HIGH EXPANSION 100-200% THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RE

20、LATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:MaterialsEngineeringStandardFormsMaterialSpecificationMatspec.doc 4. APPROVAL(PRODUCTION TRY-OUT REQUIRED)Refer HN 1000, Clause G. Production quantities shall not be accepted from

21、 any source, nor reformulated materials from an approved source until such materials have received approval from GM Holden Materials Engineering and have been subjected to a Manufacturing tryout and determined suitable for use in production. Appropriate documentation, setting out tests performed by

22、the vendor, must be submitted to GM Holden Materials Engineering demonstrating compliance with this specification. After a material or component has been listed as approved against this standard, no change may be made in source, composition, processing or identification without prior written approva

23、l by the purchaser, and such listing does not waive the obligation of the vendor to meet all detailed requirements of this standard with any shipment. 5. INSPECTION AND REJECTION Refer HN 1000, Clause C. 6. HAZARDOUS MATERIALS Refer HN 1000, Clause H. 7. RESTRICTED AND REPORTABLE SUBSTANCES (i) All

24、substances and parts must meet the requirements of GMW3059. (ii) All chemical components present in materials supplied to this specification must comply with Australian NICNAS (National Industrial Chemicals Notification and Assessment Scheme) obligations. ABN 84 006 893 232 GM Holden Limited Enginee

25、ring Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2377 6 of 6 August, 2001 September, 2007NAME: SEALER PREFORMED, WELDABLE HIGH EXPANSION 100-200% THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DO

26、CUMENT ISSUE DATE IS STILL VALID. FORM : I:MaterialsEngineeringStandardFormsMaterialSpecificationMatspec.doc 8. APPROVED SUPPLIERS AND MATERIALSMaterial known to meet the full requirements of this specification: APPROVED SUPPLIER APPROVED MATERIAL ORBSEAL 10203 9. REVISIONSMarch, 2006 - Revised sect

27、ion “3.2.2(iv) Scab corrosion” (of section “3.2 Adhesion” of “3.REQUIREMENTS”) - specified 20 cycles - Revised section “3.4.3 Weldability” (of section “3.4 Process Requirements” of “3.REQUIREMENTS”) - GM9829P was incorrectly referenced. Corrected to GM9929P. - Section “7. RESTRICTED AND REPORTABLE S

28、UBSTANCES” - inclusion of reference to NICNAS September, 2007 - Section “3. REQUIREMENTS”, Table “3.1 Physical Properties”, Physical Properties “Water absorption” and “Expansion”, - Test Methods GM9037P & GM9640P interchanged. - Revised section “7.RESTRICTED AND REPORTABLE SUBSTANCES” to directly reference GMW3059 and NICNAS requirements. Prepared by: Dinukshi Ferdinand