ImageVerifierCode 换一换
格式:PDF , 页数:1 ,大小:47.72KB ,
资源ID:785830      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-785830.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(INTERN CEMS BT-30-2009 Foam Test With Water《泡沫带水试验》.pdf)为本站会员(rimleave225)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

INTERN CEMS BT-30-2009 Foam Test With Water《泡沫带水试验》.pdf

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 1 of 1 NAVISTAR, INC. CEMS (CORPORATE ENGINEERING MATERIAL SPECI

2、FICATION) NUMBER: CEMS BT-30 TITLE: Foam Test With Water CURRENT ISSUE DATE: August 2009 WRITTEN/REVIEWED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE OF: October 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involv

3、e hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change N

4、otice: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive. 1.0 APPLICATION This method covers a procedure for determining the foaming characteristics of fluids in the presence of water. 2.0 SCOPE This specification describes the test method. 3.0 APPAR

5、ATUS 3.1 Mechanical paint shaker, Red Devil No. 30 or equivalent 3.2 Pyrex graduated cylinder, 250 milliliters 3.3 Syringe or pipette capable of delivering 2.5 milliliters 3.4 Apparatus required for ASTM D 892, Test for Foaming Characteristics of Lubricating Oils 3.5 Hot plate or bath 4.0 MATERIAL 4

6、.1 Bottles with screw caps, 16 ounce (500 milliliters), French square 4.2 Distilled water 4.3 Materials required for ASTM D 892, Test for Foaming Characteristics of Lubricating Oils 5.0 PROCEDURE 5.1 Prepare a sample as follows: 5.1.1 Heat 250 milliliters of fluid to be tested to 120 + 5 F (49 + 3 C

7、) and allow to cool to 75 + 5 F (24 + 3 C). 5.1.2 Place the fluid into a 16 ounce (500 milliliters) bottle containing 2.5 milliliters distilled water and cap securely. 5.1.3 Agitate 5 minutes on the mechanical shaker 5.2 Proceed immediately per ASTM D892, section 5 (5.1.2) 5.3 Prepare a second sampl

8、e as in (5.1.1) above and proceed per ASTM D892, section 5 (c) and 5 (d). 6.0 REPORT Foam per ASTM D 892 with 1 percent water added (three sequences). Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1