INTERN TMS 6810-2009 Lubricant Power Steering (Ross and Sheppard)《动力转向装置(Ross及Sheppard)润滑剂》.pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 1 of 3 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER:

2、TMS-6810 TITLE: Lubricant, Power Steering (Ross and Sheppard) CURRENT REV No: 0908 DATE: August 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev I - August 2004 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification ma

3、y involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use.

4、Change Notice: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added section 2.1 “Restricted Chemical Substances;” added section 10 “Technical Information;” editorial changes. Reference: File 30-8 Keywords: Lubricant; Steering Gear 1.0 APPLICATION

5、 This specification covers a power steering fluid used for factory fill in medium duty trucks and school buses that use Ross and Sheppard steering systems (Navistar Bulk P/N 2643472R1). 2.0 SCOPE This specification covers the physical and chemical properties for a modified ISO grade 46 hydraulic flu

6、id suitable for use in Ross and Sheppard power steering systems. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise spe

7、cified the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this specification. Quality System Standard ISO-9001 or TS-16949 ASTM D 97 ASTM D 811 NAVISTAR Manufacturing Std. MS-D-13 ASTM D 130 ASTM D 892 CFR Title 29, Pa

8、rt 1910 ASTM D 445 ASTM D 1549 NAVISTAR CEMS B-50 ASTM D 611 ASTM D 2270 ASTM D 92 ASTM D 665 ASTM D 2272 ASTM D 96 ASTM D 2983 4.0 REQUIREMENTS 4.1 Physical and Chemical Properties Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or

9、 networking permitted without license from IHS-,-,-NUMBER: TMS-6810 TITLE Lubricant, Power Steering (Ross and Sheppard) REVISION: 0908 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to

10、 assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 2 of 3 4.2 Viscosity (ASTM D 445) At 100 C (212 F) kinematic, cSt (mm2/s), 7.0 minimum At 40 C (104 F) kinematic, cSt (mm2/s), 48.3 maximum At -40 C (-40 F) BROOKFIELD (ASTM D 2983) cP, 35,000 maximum - 4.3 Viscosity Index (ASTM D

11、 2270) Shall be 130 minimum. 4.4 Pour Point (ASTM D 97) Shall be -42 C (-44 F) maximum - 4.5 Flash Point (ASTM D 92) Shall be 176 C (350 F) minimum 4.5.1 Foaming (ASTM D 892) When tested at the following temperatures, foaming tendency and foam stability shall be as follows: Temperature Foam Tendency

12、 Foam Stability 24 C (75 F) 50 ml, max 0 ml, max 93 C (200 F) 50 ml, max 0 ml, max 24 C (75 F) after testing at 93 C (200 F) 50 ml, max 0 ml, max 4.5.2 Water and Sediments (ASTM D 96, Method A, without demulsifier or water) Shall be 0.05% maximum. 4.5.3 Zinc Content (ASTM D 811 or D 1549) Shall be 4

13、0-120 ppm. 4.5.4 Aniline Point (ASTM D 611) Shall be 90 - 105 C (194 - 221 F) 4.5.5 Corrosion Test (ASTM D 665) Must pass procedures A and B. 4.5.6 Copper Strip Corrosion ASTM D 130, 3 hours 100 C (212 F) Rating shall be classification 1B, maximum. 4.5.7 Oxidation Stability (ASTM D 2272) Shall be 20

14、0 minutes, minimum. 4.5.8 Steering Test Must be approved by TRW Commercial Steering Division, R. H. Sheppard Company, Bosch Braking Systems, and LUK Automotive Hydraulics. 5.0 QUALIFICATION Material submitted for qualification shall be accompanied by detailed test reports and certification that mate

15、rial supplied meets all requirements. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6810 TITLE Lubricant, Power Steering (Ross and Sheppard) REVISION: 0908 This docu

16、ment is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 3 of 3 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements A

17、ll suppliers to Navistar are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain t

18、heir certification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples, which

19、were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes occur in material properties, processing practices, or labeling, the supplier shall notify Materials Engineering at TDTC and Navistar Purchasing and Supplier De

20、velopment of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new/amended/updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Section 1910, shall be submitted with the request for change. 6.3 Process Cont

21、rol The supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required propertie

22、s. The part supplier and the plant metallurgist and/or the quality control manager of the using NAVISTAR plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING AND IDENTIFICATION Shipping and identification shall be in accordance with Navistar Manufacturing Standar

23、d MS-D-13. When packaged for resale, containers, packaging and identification shall be in accordance with requirements set forth by the Parts Marketing Division of the Parts Operation at Cantera in Warrenville, Illinois. 8.0 DESIGNATION ON DRAWINGS Lubricant per TMS-6810 9.0 APPROVED SOURCE Power St

24、eering Fluid 51204 Shell Code 20631 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Techn

25、ology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-