INTERN TMS 6930-2009 Glass Assembly Adhesive《玻璃总成粘合剂》.pdf

1、This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 1 of 7 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS

2、-6930 srr TITLE: Glass Assembly Adhesive CURRENT REV No.: 0912 DATE: December 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE DATED: August 2002 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve haza

3、rdous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice:

4、 Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; editorial changes. Reference: File 30-1 Keywords: Glass Bonding, Adhesives, Adhesive systems 1.0 APPLICATION This specification covers glass assembly adhesive systems us

5、ed primarily for bonding laminated or tempered glass to metal or plastic components in the construction of trucks and tractors. Components include such items as: studs, latches, hinges, and sashes, etc. 2.0 SCOPE This specification covers the material properties, performance requirements, production

6、 quality and process control, suppliers responsibility, source approval and quality control, general information, and sources for approved adhesive systems. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with t

7、he requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards applies. The following specifications, standards, and regulations are referenced herein. Quality System Standard ISO 9001 or TS-16949 NAVISTAR TMS-9522 CFR

8、 Title 29, Section 1910 NAVISTAR TMS-9543 NAVISTAR Manufacturing Std. MS-D-13 SAE J243 NAVISTAR Eng. Design Std. A-16 SAE J1523 NAVISTAR CEMS B-50 ASTM D 1002 NAVISTAR CEMS C-10 ASTM D 3163 NAVISTAR CEMS G-5 ASTM B 117 NAVISTAR CEMS GT-7E 4.0 GENERAL REQUIREMENTS Adhesive materials supplied to this

9、specification shall bond the intended substrates to produce a permanent and structural bond. The general properties of as-received materials in the uncured state are listed in Table 5. It is the responsibility of the adhesive supplier to insure compatibility of the new Copyright Navistar Internation

10、al Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permiss

11、ion from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 2 of 7 adhesive materials with the Assembly Plants product materials and processes and obtain approval from the Production Process Manager of the Assembly Plant for th

12、e use of new adhesive materials. 4.1 General Properties All properties shall be reported on submitted test reports and specific material properties will be included in Table 4. Performance requirements are listed in Section 4.3. 4.1.1 Uncured Properties Requirements for specific uncured properties a

13、re to be agreed upon between the material supplier, equipment supplier and the applicator. Uncured properties shown herein are provided for reference only. 4.2 Sample Preparation A minimum of five samples shall be prepared for each condition tested. Prepare samples per SAE J1523 except as indicated.

14、 See Figure 1. The surface condition tested shall be representative of production conditions and fully described in the test report. The bond line shall be between .5 and 1 mm (.020 and .040 inches) with an overlap of 12.5 mm (.5 inch) unless otherwise directed. The cure conditions* shall be describ

15、ed fully in the test report and should closely match the production cure conditions. These cure conditions will be listed on the attached tables and shall be reproducible for future testing. * Times and temperatures should represent actual bond line conditions. 4.3 Property And Performance Requireme

16、nts 4.3.1 Lap Shear Strength 4.3.1.1 Method: Prepare samples as directed in 4.2 Sample Preparation. Test per ASTM D 3163 or ASTM D 1002, as appropriate. Tensile machine jaw separation rate shall be 13 mm (.5 in) per minute. Test overlap shear at the indicated specified temperatures (see Table 1) aft

17、er holding at temperature for 30 minutes. Report the average failure loads of the five tests. 4.3.1.2 Required: See Table 1 for required values. TABLE 1: BOND STRENGTH (1) Lap Shear (1) Material: Glass to Metal Condition MPa psi minimum (1) 25 2C * 2.1 305 (2) -40 2C * 2.1 305 120 2C * 1.5 218 (2) H

18、eat Age 2.1 305 Water Immersion 2.1 305 (2) 500 hr Humidity 2.1 305 1000 hr Humidity 2.1 305 Cyclic Aging 2.1 305 (2) *Test at these conditions. (1) Samples will be pulled at the rate as specified in 4.3.1 Lap Shear Strength until failure. Report the failure mode for each test. (2) Screening tests.

19、Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc.

20、 or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 3 of 7 4.3.1.3 Humidity 4.3.1.3.1 Method: Test per CEMS GT-7E on coupons prepared in 4.2 Sample Preparation for length of time (see Table

21、 1) and then perform shear test upon removal from humidity. Shear strength test for 500 hours. 4.3.1.3.2 Required: See Table 1. 4.3.1.4 Water Immersion 4.3.1.4.1 Method: Prepare coupons per Section 4.2 Sample Preparation. Immerse coupons in distilled water at 25C 2C (77F 3.6F) for 500 hours. Perform

22、 shear strength test as soon as samples are removed from immersion. 4.3.1.4.2 Required: See Table 1. OVERLAP SHEAR TEST SAMPLE 4.3.1.5 Heat Aging 4.3.1.5.1 Method: Prepare samples for lap shear as directed in 4.2 Sample Preparation. Heat age in a recirculating air oven for 500 hours at 90 2C (194 3.

23、6F). Perform shear test, as indicated in Section 4.3.1.1, upon removal from heat aging. 4.3.1.5.2 Required: See Table 1. 4.3.1.6 Cyclic Aging 4.3.1.6.1 Method: Prepare samples for lap shear as directed in 4.2 Sample Preparation. Test overlap shear after the 6-week environmental conditioning period l

24、isted below, allowing samples to return to ambient room temperature for 24 hours prior to testing. The 6-week cyclic aging shall be as follows: 4.3.1.6.1.1 16 hours humidity 4.3.1.6.1.2 2 hours -30 2C (-22 3.6F) 4.3.1.6.1.3 2 hours at ambient conditions 4.3.1.6.1.4 2 hours 70 2C (158 3.6F) 4.3.1.6.1

25、.5 2 hours salt spray per ASTM B 117 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and

26、may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 4 of 7 4.3.1.6.1.6 Repeat 24 hour cycle until 6-week period has elapsed - cycle may be interrupted f

27、or weekends and holidays, in which case leave the samples in humidity for that period. 4.3.1.6.2 Required: See Table 1. 4.3.2 Functional Cycle Testing (if specified) 4.3.2.1 Method: Subject production intent samples to functional cycle testing as specified in engineering validation plan. All testing

28、 shall be completed on actual modules or holding fixtures made to simulate modules. 4.3.2.2 Required: Upon completion of all testing, there shall be no evidence of any structural or adhesive failure. TABLE 2: SUBSTRATES ITEM DESCRIPTION SPECIFICATION DESCRIPTION 1 E-coat CEMS G-5 Part V Grade -56 Ca

29、thodic E-coat BASF U32 2a Laminated Glass TMS-9522 Windshield, drop glass 2b Tempered Glass TMS-9522 Side, back and drop glass 3 Anodized 6063-T6 Aluminum CEMS C-10 Cab TABLE 3: CURE CYCLES ITEM DESCRIPTION CYCLE A1 Ambient Cure Follow and report manufacturers recommended practice. TABLE 4: MATERIAL

30、S AND GENERAL PROPERTIES ID SUPPLIER/ MATERIAL CODE VISCOSITY Kcps OPEN TIME* 23 C Minutes COLOR A1 Dow Automotive Urethane BETAMATE 73100 10-30 4-6 Dark gray BETAMATE 73005 10-30 Light tan *Note Open Time refers to the interval of time between the spreading of the adhesive on the adherent and the c

31、ompletion of the assembly of the parts for bonding. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is

32、restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 5 of 7 TABLE 5: APPROVED MATERIAL (1), SUBSTRATE AND CURE CYCLE MATERIAL SYSTEM(S) (s

33、ee Table 4) SUBSTRATE(S) (see Table 2) CURE CYCLE(S) (see Table 3) QUALIFIED SHEAR STRENGTH (see Table 1) MPa psi APPROVAL LEVEL/ REPORT NUMBER (2) COMMENTS A1 2b, 3 A1 2.1 (305) A (1)Only material and substrate combinations listed in this table are considered “Approved.” New material combinations m

34、ay be approved by letter or report until specification updates are made. (2) Approval levels are as follows: Navistar Report number Full approval as documented in the Navistar report. A Grandfathered approval. Current production applications are required to submit test reports to this specification

35、to maintain approvals. B Approved for prototypes and pre-production applications. 5.0 QUALIFICATION Material and processes submitted for approval to this specification shall include the following: 5.2.1 A detailed, signed test report documenting testing to this specification prepared per TMS-9543. 5

36、.2.2 Test coupons or photographs showing failure modes for each test 5.2.3 The complete procedure used for preparing and curing materials for test, especially surface preparation and condition of the test coupons. 5.2.4 Adhesive, substrate and any chemicals used for bonding. Note: Questions regardin

37、g qualification requirements, reports and test materials shall be directed to: Manager of Non-Metallic Materials Materials Engineering and Technology Development Truck Development and Technology Center PO Box 1109 Fort Wayne, IN 46801 MaterialsE 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier R

38、equirements All suppliers to Navistar are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers mu

39、st maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitte

40、d without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar

41、 Inc. DECEMBER 2009 Page 6 of 7 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In t

42、he event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, Truck Development and Technology Center, and Navistar Purchasing and Supplier Development of the proposed change(s). Tes

43、t data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Process Control The supplier shall either perform

44、and/or report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant

45、metallurgist and/or the quality control manager of the using Navistar plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION Loading, packing and identification shall be in accordance with Manufacturing Std. MS-D-13. 8.0 DESIGNATION ON D

46、RAWINGS The drawing designation may be written in a general or specific manner depending on the requirements of the situation. The specification for a bonded assembly may be written as: Bond per TMS-6930 9.0 TECHNICAL INFORMATION For further information related to the technical content of this speci

47、fication, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80

48、112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ 10.0 APPROVED SOURCES Dow Automotive Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and may not be se