INTERN TMS 9503-2009 Exterior Plastic Film Application Procedure《外部塑料薄膜的应用程序》.pdf

1、 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar Inc. DECEMBER 2009 Page 1 of 4 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER:

2、 TMS-9503 TITLE: Exterior Plastic Film, Application Procedure CURRENT REV No.: 0912 DATE: December 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev. B-1, August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specificati

3、on may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to

4、use. Change Notice: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; editorial changes. Reference: File 30-11B Keywords: Exterior Plastic Film Application 1.0 APPLICATION This standard outlines the procedure for applyin

5、g decorative pressure sensitive films to painted exterior body sections such as fenders, doors, quarter panels and tailgates. The material specification for the plastic film, TMS-7107 or CEMS G-7, types will be specified on the engineering drawing for the part or assembly. The application of these f

6、ilms shall be made after the body section has been completely painted, inspected and approved for delivery to the trim line. Application areas shall be specified on engineering drawings. 2.0 SCOPE This specification covers the procedure for applying the film, including surface preparation, applicati

7、on method, inspection and process quality control. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the la

8、test issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 NAVISTAR CEMS B-50 CFR Title 29, Section 1910 NAVISTAR CEMS G-7 NAVISTAR Manufacturing Std. MS-D-13 NAVISTAR

9、TMS-7107 NAVISTAR Eng. Design Std. A-16 NAVISTAR TMS-9543 4.0 REQUIREMENTS 4.1 Surface Preparation 4.1.1 Sanding of Paint Wet sand with #360 paper. All metal and/or paint nibs are removed during the sanding operation. Such defects will telescope through the vinyl film. Copyright Navistar Internation

10、al Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-9503 TITLE: Exterior Plastic Film, Application Procedure REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or repr

11、oduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar Inc. DECEMBER 2009 Page 2 of 4 4.1.2 Cleaning The body surface to which the decorative film will be bonded must be free of grease, oil and other foreign material. Wip

12、e with clean cloth soaked in isopropyl alcohol. 4.2 Application 4.2.1 Temperature The film is most easily handled when air and application surface temperatures are between 21-32C (70-90F). For applications below 21C (70F), use heat lamps, a jet of steam, or a heat gun to warm the surfaces to which t

13、he film is to be applied as well as the film itself. 4.2.2 Wetting Solution Thoroughly mix two to three level teaspoons of detergent (American Cyanamid Aerosol OT 75% AQ) per one gallon of clean, warm 32-35C (90-95F) water. NEVER USE SOAP OR HARSH DETERGENTS. The mixing container should be stainless

14、 steel or plastic. 4.2.3 Wetting of the Body and Decorative Film Adhesive Surfaces Thoroughly wet the application surfaces of the body and the adhesive surface of the decorative film with the wetting solution. This can be accomplished with a sponge saturated with wetting solution or any other suitab

15、le method of application (such as immersing the film without paper backing). 4.2.4 Removal of Backing Bend a corner of the film toward the DECORATIVE FACE side to separate from the film. Lay the film on a clean, warm, flat surface BACKING SIDE UP. Hold the film firmly to the surface and remove the b

16、acking with a smooth 180 peeling motion. IT IS MANDATORY TO REMOVE THE BACKING FROM THE FILM - NEVER THE FILM FROM THE BACKING, AS POSSIBLE FILM STRETCHING OR BREAKING MAY RESULT. Note: Under hot, humid conditions, a slight jerking motion will aid in removing the backing. 4.2.5 Apply Wet Decorative

17、Film to Body Surfaces Immediately apply the wetted decorative film to the panel. Center the decorative film, smoothing out all ripples with the hand in the area to be covered. Apply the wetting solution to the outer surface of the film. 4.2.6 Pressurize and Level Off 4.2.6.1 Flat Surfaces Using a pl

18、astic squeegee, pressurize all of the flat surfaces with firm, overlapping strokes to remove all air bubbles, water and wrinkles. On vertical surfaces pressurize and level off the entire top edge first with a 75 x 100 mm (3 x 4 in) squeegee and then work from top to bottom using a 20 cm (8 in) squee

19、gee, with firm overlapping strokes. On horizontal surfaces, start at the center and work toward the edges, using a 75 x 100 mm (3 x 4 in) squeegee. DO NOT APPLY PRESSURE TO EDGES THAT WILL BE WRAPPED AROUND THE DOORS, FENDERS OR GAS CAP AREAS, OR TO COMPOUND CURVE AREAS. Pressurize the surface a sec

20、ond time and then dry the surface with a piece of clean cheesecloth. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-9503 TITLE: Exterior Plastic Film, Application Pro

21、cedure REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar Inc. DECEMBER 2009 Page 3 of 4 4.2.6.2 Flange Areas (a) Wipe flange

22、 area and the adhesive side of film with a lint free cloth, dampened with isopropyl alcohol. Allow the isopropyl alcohol to evaporate. IT IS EXTREMELY CRITICAL THAT THIS AREA BE CLEAN. (b) Warm the unapplied film by passing steam or a heat gun over the surface. (c) Wrap the film around the flange ar

23、ea and press it firmly into position. AVOID TRAPPING AIR WHEN TURNING THE EDGE. (d) Pressurize the flange area and door edge with 75 x 100 mm (3 x 4 in) squeegee. 4.2.6.3 Contoured Areas (a) Warm the unapplied film by passing steam or heat gun over the surface, working on an area no more than 12.7 m

24、m (1/2 in) larger than the squeegee. (b) Using the 75 x 100 mm (3 x 4 in) plastic squeegee, pressurize and level off this small warmed area. (c) Repeat the warming and pressurizing until the entire contoured surface is completely adhered and free of air, water and wrinkles. (d) Trim all excess mater

25、ial. CAUTION: If a knife is used for trimming, a back-up template must be used under the film to prevent damage to the painted areas. 4.3 Inspection It is mandatory that each area, upon completion of that area, be inspected for blisters due to trapped air or water. All blisters shall be worked out w

26、ith the squeegee, or punctured with a sharp needle or pin (not a knife) and then pressurized until the film adheres to the body surface. In addition, the entire film, especially the edges, must be checked for adherence. 4.4 Process Control Each step and detail in the procedure is significant to achi

27、eve satisfactory adhesion and appearance in the shortest time. Accordingly, revisions to or deviations from this specification without prior test and approval by the Navistar Truck Development and Technology Center is not recommended. 5.0 QUALITY All product supplied shall be clean and free from dir

28、t, oils, sharp edges, or defects harmful to product performance. 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements All suppliers to Navistar Inc. are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supp

29、lier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. Copyright Navi

30、star International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-9503 TITLE: Exterior Plastic Film, Application Procedure REVISION: 0912 This document is restricted and may not be sent outside Navis

31、tar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar Inc. DECEMBER 2009 Page 4 of 4 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all r

32、espects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall n

33、otify Materials Engineering, Truck Development and Technology Center, and Navistar Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSD

34、S), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Process Control The supplier shall either perform and/or report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot hav

35、ing been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using Navistar plant may determine testing and reporting requirements on specific products. 7.0

36、SHIPPING, PACKING AND IDENTIFICATION (Not Applicable) 8.0 DESIGNATION ON DRAWING Apply per TMS-9503. 9.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materi

37、als Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-