ISA 75 08 05-2016 Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (Class 150 300 600 900 1500 and 2500) (Formerly ISA 75 15).pdf

1、 AMERICAN NATIONAL STANDARD ANSI/ISA-75.08.05-2016 Formerly ANSI/ISA-75.15-1994 Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (Class 150, 300, 600, 900, 1500, and 2500) Approved 28 July 2016 ANSI/ISA-75.08.05-2016 Face-to-Face Dimensions for Buttweld-End Globe-Style Control Val

2、ves (Classes 150, 300, 600, 900, 1500, and 2500) ISBN: 978-1-945541-01-8 Copyright 2016 by the International Society of Automation (ISA). All rights reserved. Not for resale. Printed in the United States of America. No part of this publication may be reproduced, stored in a retrieval system, or tran

3、smitted in any form or by any means (electronic mechanical, photocopying, recording, or otherwise), without the prior written permission of the Publisher. ISA 67 Alexander Drive P.O. Box 12277 Research Triangle Park, North Carolina 27709 - 3 - ANSI/ISA-75.08.05-2016 Preface This preface, as well as

4、all footnotes and annexes, is included for information purposes and is not part of ANSI/ISA-75.08.05-2016. The standards referenced within this document may contain provisions which, through reference in this text, constitute requirements of this document. At the time of publication, the editions in

5、dicated were valid. All standards are subject to revision, and parties to agreements based on this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated within this document. Members of IEC and ISO maintain registers of currently valid

6、 International Standards. ANSI maintains registers of currently valid U.S. National Standards. This document has been prepared as part of the service of ISA toward a goal of uniformity in the field of instrumentation. To be of real value, this document should not be static but should be subject to p

7、eriodic review. Toward this end, the Society welcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709; Telephone (919) 549-8411; Fax (919) 549-8288; E-mail: standar

8、dsisa.org. The ISA Standards and Practices Department is aware of the growing need for attention to the metric system of units in general, and the International System of Units (SI) in particular, in the preparation of instrumentation standards. The Department is further aware of the benefits to USA

9、 users of ISA standards of incorporating suitable references to the SI (and the metric system) in their business and professional dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable metric units in all new and revised standards, recommended practi

10、ces, and technical reports to the greatest extent possible. Standard for Use of the International System of Units (SI): The Modern Metric System, published by the American Society for Testing certifies industry professionals; provides education and training; publishes books and technical articles; h

11、osts conferences and exhibits; and provides networking and career development programs for its 40,000 members and 400,000 customers around the world. ISA owns A, a leading online publisher of automation-related content, and is the founding sponsor of The Automation Federation (www.automationfederati

12、on.org), an association of non-profit organizations serving as “The Voice of Automation.“ Through a wholly owned subsidiary, ISA bridges the gap between standards and their implementation with the ISA Security Compliance Institute (www.isasecure.org) and the ISA Wireless Compliance Institute (www.is

13、a100wci.org). The following people served as members of ISA Subcommittee ISA75.08 and approved ANSI/ISA-75.08.05-2016: NAME COMPANY W. Weidman, Chair Consultant V. Mezzano, Managing Director Fluor Corporation H. Baumann H B Services Partners LLC F. Cain Flowserve Corporation R. Duimstra Fisher Contr

14、ols International Inc. J. Young The Dow Chemical Company The following people served as members of ISA Committee ISA75 and approved ANSI/ISA-75.08.05-2016: NAME COMPANY J. Young, Chair The Dow Chemical Company V. Mezzano, Co-Managing Director Fluor Corporation W. Weidman, Co-Managing Director Consul

15、tant - 5 - ANSI/ISA-75.08.05-2016 A. Abromaitis S&T Design H. Baumann H B Services Partners LLC J. Beall Emerson Process Management M. Bober SPX Flow Technology H. Boger Consultant S. Boyle Consultant F. Cain Flowserve Corporation R. Duimstra Fisher Controls International Inc. J. Faramarzi Control C

16、omponents Inc. C. Hergert Kellogg Brown & Root H. Hoffmann Consultant J. Kiesbauer Samson Aktiengesellschaft A. Libke DeZURIK G. Liu Consultant T. Loudin Larox Flowsys Inc. D. Martin Valve Solutions Ltd. H. Maxwell Haines Fluid Dynamics H. Miller Consultant A. Sahraei Enbridge Pipelines Inc LP E. Sk

17、ovgaard Consultant This standard was approved by the ISA Standards and Practices Board on 18 July 2016: NAME COMPANY N. Sands, Vice President DuPont D. Bartusiak ExxonMobil Research & Engineering P. Brett Honeywell Inc. E. Cosman OIT Concepts, LLC D. Dunn Phillips 66 J. Federlein Federlein & Assoc.

18、LLC B. Fitzpatrick Wood Group Mustang J. Gilsinn Kenexis Consulting J.-P. Hauet KB Intelligence J. Jamison Encana Corp. D. Lee UCDS K.-P. Lindner Endress+Hauser Process Solutions AG T. McAvinew Consultant V. Mezzano Fluor Corp. C. Monchinski Automated Control Concepts Inc. D. Reed Rockwell Automatio

19、n H. Sasajima Fieldcomm Group Inc. Asia-Pacific T. Schnaare Rosemount Inc. J. Tatera Tatera & Associates Inc. K. Unger Consultant I. Verhappen Industrial Automation Networks D. Visnich Burns & McDonnell W. Weidman Consultant J. Weiss Applied Control Solutions LLC M. Wilkins Yokogawa D. Zetterberg Ch

20、evron Energy This page intentionally left blank. - 7 - ANSI/ISA-75.08.05-2016 Contents 1 Scope . 9 2 Purpose 9 3 Definitions 9 4 Dimensional data . 9 5 References . 11 Annex A Dimensions for metrically sized valves 13 This page intentionally left blank. 9 ANSI/ISA-75.08.05-2016 1 Scope This standard

21、 applies to buttweld-end globe-style control valves, sizes 15 mm (1/2 inch) through 450 mm (18 inches) for Classes 150 through 2500, having top, top and bottom, port, or cage guiding. 2 Purpose 2.1 The purpose of this standard is to aid users in their piping designs by providing buttweld-end globe-s

22、tyle control valve dimensions, without giving special consideration to the equipment manufacturer to be used. 2.2 The short-long dimensions provided in Table 1 clarify 2.1 by consolidating the diversity of existing manufacturers lengths into two sets of dimensions for each valve size. Before using e

23、ither the short or long dimensions, the piping designer should confirm with the selected valve manufacturer which dimension is correct for the valve(s) being supplied. 3 Definitions For definitions of terms used in this standard, see ISA-75.05.01, Control Valve Terminology. 4 Dimensional data For fa

24、ce-to-face dimensions for buttweld-end globe-style control valves, see Table 1. ANSI/ISA-75.08.05-2016 10 Table 1 Face-to-face dimensions for buttweld-end globe-style control valves Nominal Valve Size PN 10, 16, 20, 25, 40, 50, 63 & 100 (Classes 150, 300, & 600) PN 150 & 250 (Classes 900 & 1500) PN

25、420 (Class 2500) Tolerance Dimension “A” Dimension “A” Dimension “A” mm inches mm inches mm inches mm Inches Short Long Short Long Short Long Short Long Short Long Short Long mm inches 15 1/2 187 203 7.38 8.00 194 279 7.62 11.00 216 318 8.50 12.50 1.6 0.062 20 3/4 187 206 7.38 8.12 194 279 7.62 11.0

26、0 216 318 8.50 12.50 1.6 0.062 25 1 187 210 7.38 8.25 197 279 7.75 11.00 216 318 8.50 12.50 1.6 0.062 40 1-1/2 222 251 8.75 9.88 235 330 9.25 13.00 260 359 10.25 14.12 1.6 0.062 50 2 254 286 10.00 11.25 292 375 11.50 14.75 318 400 12.50 15.75 1.6 0.062 65 2-1/2 292 311 11.50 12.25 292 375 11.50 14.7

27、5 318 400 12.50 15.75 1.6 0.062 80 3 318 337 12.50 13.25 318 460 12.50 18.12 381 498 15.00 19.62 1.6 0.062 100 4 368 394 14.50 15.50 368 530 14.50 20.88 406 575 16.00 22.62 1.6 0.062 150 6 451 508 17.75 20.00 508 768 24.00 30.25 610 819 24.00 32.25 1.6 0.062 200 8 543 610 21.38 24.00 610 832 24.00 3

28、2.75 762 1029 30.00 40.25 1.6 0.062 250 10 673 752 26.50 29.62 762 991 30.00 39.00 1016 1270 40.00 50.00 1.6 0.062 300 12 737 819 29.00 32.35 914 1130 36.00 44.50 1118 1422 44.00 56.00 3.2 0.125 350 14 851 1029 33.50 40.50 1257 49.50 1803 71.00 3.2 0.125 400 16 1016 1108 40.00 43.62 1422 56.00 3.2 0

29、.125 450 18 1143 45.00 1727 68.00 3.2 0.125 11 ANSI/ISA-75.08.05-2016 5 References AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) ASME B16.25-2003 Buttwelding Ends ASME B16.34-2004 Valves Flanged, Threaded, and Welding End Available from: ASME Three Park Avenue New York, NY 10016-5990 Tel: 800-843-

30、2763 http:/www.asme.org INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC) IEC 60534-3-3 (1998) Industrial-Process Control Valves - Part 3-3: Dimensions End-to-End Dimensions for Buttweld, Two-Way, Globe-Type, Straight Pattern Control Valves Available from: IEC 3, rue de Varemb P.O. Box 131 CH - 1211 G

31、eneva 20 Switzerland http:/www.iec.ch This page intentionally left blank. 13 ANSI/ISA-75.08.05-2016 Annex A Dimensions for metrically sized valves This annex is not part of ANSI/ISA-75.08.05-2016, but is included to facilitate its use. The ANSI standards listed in the bibliography contain valve body

32、 design information in addition to face-to-face dimensions. Dimensions for metrically sized valves are nominal conversions that are conventionally used in the Manufacturers Standardization Society (MSS) of the Valve and Fitting Industrys Publication MSS-SP-86, and in International Standards Organiza

33、tion (ISO) and International Electrotechnical Commission (IEC) documents. This page intentionally left blank. Developing and promulgating sound consensus standards, recommended practices, and technical reports is one of ISAs primary goals. To achieve this goal the Standards and Practices Department

34、relies on the technical expertise and efforts of volunteer committee members, chairmen and reviewers. ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers United States Technical Advisory Groups (USTAGs) and provides secretariat support for International El

35、ectrotechnical Commission (IEC) and International Organization for Standardization (ISO) committees that develop process measurement and control standards. To obtain additional information on the Societys standards program, please write: ISA Attn: Standards Department 67 Alexander Drive P.O. Box 12277 Research Triangle Park, NC 27709 ISBN: 978-1-945541-01-8