ISA 76 00 02-2002 Modular Component Interfaces for Surface-Mount Fluid Distribution Components - Part 1 Elastomeric Seals《安装于表面的流体分布部件的模块化部件接口 第1部分 弹性密封》.pdf

1、 AMERICAN NATIONAL STANDARD ANSI/ISA-76.00.02-2002 Modular Component Interfaces for Surface-Mount Fluid Distribution Components - Part 1: Elastomeric Seals Approved 13 June 2002 ANSI/ISA-76.00.02-2002Modular Component Interfaces for Surface-Mount Fluid Distribution Components Part 1: ElastomericSeal

2、sISBN: 978-1-55617-810-8Copyright 2002 by ISA The Instrumentation, Systems, and Automation Society. All rights reserved.Not for resale. Printed in the United States of America. No part of this publication may be reproduced,stored in a retrieval system, or transmitted in any form or by any means (ele

3、ctronic, mechanical,photocopying, recording, or otherwise), without the prior written permission of the Publisher.ISA67 Alexander DriveP.O. Box 12277Research Triangle Park, North Carolina 27709- 3 - ANSI/ISA-76.00.02-2002PrefaceThis preface, as well as all footnotes and annexes, is included for info

4、rmation purposes and is not part ofANSI/ISA-76.00.02-2002.This document has been prepared as part of the service of ISA the Instrumentation, Systems, andAutomation Society toward a goal of uniformity in the field of instrumentation. To be of real value, thisdocument should not be static but should b

5、e subject to periodic review. Toward this end, the Societywelcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards andPractices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709;Telephone (919) 549-8411; Fax (919) 549-8288; E-ma

6、il: standardsisa.org.The ISA Standards and Practices Department is aware of the growing need for attention to the metricsystem of units in general, and the International System of Units (SI) in particular, in the preparation ofinstrumentation standards. The Department is further aware of the benefit

7、s to USA users of ISAstandards of incorporating suitable references to the SI (and the metric system) in their business andprofessional dealings with other countries. Toward this end, this Department will endeavor to introduceSI-acceptable metric units in all new and revised standards, recommended p

8、ractices, and technicalreports to the greatest extent possible. Standard for Use of the International System of Units (SI): TheModern Metric System, published by the American Society for Testing orb) the 57.2-mm (2.25-inch) footprint, spaced on 58.0-mm (2.28-inch) centerlines, with flow and boltloca

9、tions positionally toleranced to the same numeric values as a single position component (seeFigure 2).ANSI/ISA-76.00.02-2002 - 12 -Figure 1 Standard block for surface-mounted distribution components(all dimensions in mm)- 13 - ANSI/ISA-76.00.02-2002Figure 2 Optional block for larger surface-mounted

10、distribution components(all dimensions in mm)This page intentionally left blank.Developing and promulgating sound consensus standards, recommended practices, and technicalreports is one of ISAs primary goals. To achieve this goal the Standards and Practices Departmentrelies on the technical expertis

11、e and efforts of volunteer committee members, chairmen and reviewers.ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers UnitedStates Technical Advisory Groups (USTAGs) and provides secretariat support for InternationalElectrotechnical Commission (IEC) and

12、 International Organization for Standardization (ISO) committeesthat develop process measurement and control standards. To obtain additional information on theSocietys standards program, please write:ISAAttn: Standards Department67 Alexander DriveP.O. Box 12277Research Triangle Park, NC 27709ISBN: 978-1-55617-810-8