ITU-R BT 1614-1-2012 Payload identification data structure for digital television interfaces《数字电视接口的有效负荷识别数据结构》.pdf

1、 Recommendation ITU-R BT.1614-1 (01/2012) Payload identification data structure for digital television interfaces BT Series Broadcasting service (television) ii Rec. ITU-R BT.1614-1 Foreword The role of the Radiocommunication Sector is to ensure the rational, equitable, efficient and economical use

2、of the radio-frequency spectrum by all radiocommunication services, including satellite services, and carry out studies without limit of frequency range on the basis of which Recommendations are adopted. The regulatory and policy functions of the Radiocommunication Sector are performed by World and

3、Regional Radiocommunication Conferences and Radiocommunication Assemblies supported by Study Groups. Policy on Intellectual Property Right (IPR) ITU-R policy on IPR is described in the Common Patent Policy for ITU-T/ITU-R/ISO/IEC referenced in Annex 1 of Resolution ITU-R 1. Forms to be used for the

4、submission of patent statements and licensing declarations by patent holders are available from http:/www.itu.int/ITU-R/go/patents/en where the Guidelines for Implementation of the Common Patent Policy for ITU-T/ITU-R/ISO/IEC and the ITU-R patent information database can also be found. Series of ITU

5、-R Recommendations (Also available online at http:/www.itu.int/publ/R-REC/en) Series Title BO Satellite delivery BR Recording for production, archival and play-out; film for television BS Broadcasting service (sound) BT Broadcasting service (television) F Fixed service M Mobile, radiodetermination,

6、amateur and related satellite services P Radiowave propagation RA Radio astronomy RS Remote sensing systems S Fixed-satellite service SA Space applications and meteorology SF Frequency sharing and coordination between fixed-satellite and fixed service systems SM Spectrum management SNG Satellite new

7、s gathering TF Time signals and frequency standards emissions V Vocabulary and related subjects Note: This ITU-R Recommendation was approved in English under the procedure detailed in Resolution ITU-R 1. Electronic Publication Geneva, 2012 ITU 2012 All rights reserved. No part of this publication ma

8、y be reproduced, by any means whatsoever, without written permission of ITU.Rec. ITU-R BT.1614-1 1 RECOMMENDATION ITU-R BT.1614-1 Payload identification data structure for digital television interfaces (Question ITU-R 130/6) (2003-2012) Scope The payload identification packet is intended to be inser

9、ted into the interface(s) carrying digital images, digital audio, and other ancillary data. Where multiple interfaces are used to carry data exceeding the bandwidth of one link the identification packet is used to identify the individual links. The identification packet may be used to provide receiv

10、ers with information concerning the payload being received. The ITU Radiocommunication Assembly, considering a) that many countries have installed digital television production facilities based on the use of digital video components conforming to Recommendations ITU-R BT.601, ITU-R BT.656, ITU-R BT.

11、709 and ITU-R BT.799; b) that high definition television (HDTV) production systems are being installed based on digital HDTV interfaces conforming to Recommendation ITU-R BT.1120; c) that there are operational and economic benefits if a single infrastructure is used to carry a variety of source form

12、ats; d) that it is necessary to identify the payloads carried over an interface that may be used for a variety of source formats; e) that multiple links may be used to accommodate bandwidth requirements beyond those that can be carried by the single link interface of Recommendation ITU-R BT.1120, re

13、commends 1 that the payload identification described in Annex 1 should be used; 2 that Note 1 is considered as part of the Recommendation. NOTE 1 Compliance with this Recommendation is voluntary. However, the Recommendation may contain certain mandatory provisions (to ensure, e.g., interoperability

14、or applicability) and compliance with the Recommendation is achieved when all of these mandatory provisions are met. The words “shall” or some other obligatory language such as “must” and the negative equivalents are used to express requirements. 2 Rec. ITU-R BT.1614-1 Annex 1 Normative Reference Re

15、commendation ITU-R BT.1364 “Format of ancillary data signals carried in digital component studio interface”. 1 General1 This Recommendation defines a metadata payload identifier data structure that may be added to digital television interfaces for the purpose of identifying the interface payload. Th

16、e payload identifier is intended for application to all existing and future digital television interfaces. The identifier shall have a data structure type 2 as defined in Recommendation ITU-R BT.1364, constrained to 10-bit interfaces only. The payload identifier shall be used to identify the video,

17、audio, and ancillary data payload carried on a digital interface transport. The payload identifier shall be 4 bytes long where each byte has a separate significance. The first byte of the payload identifier shall have the highest significance and subsequent bytes shall be used to define lower order

18、payload information. Once assigned, byte 1 values cannot be re-purposed if the specific payload identification code is deprecated in the future. 1.1 Payload data structure The ancillary data packet used by the payload identifier shall use the Type 2 data identification having first data identificati

19、on (DID) word followed by secondary data identification (SDID) word. The DID word shall be set to the value 41h. The SDID word shall be set to the value of 01h. Table 1 outlines the ancillary data packet words with values where appropriate. The total size of the ancillary data packet is 11 words. TA

20、BLE 1 Ancillary data packet structure for the payload identifier Name Acronym Value Ancillary data flag (10-bit words) ADF 000h, 3FFh, 3FFh Data identification DID 41h Secondary data identification SDID 01h Data count DC 04h SDI video payload identifier 4 words Checksum CS 1 Use of payload identifie

21、rs conforming to Recommendation ITU-R BT.1614 (2003) are deprecated. Rec. ITU-R BT.1614-1 3 2 General payload identifier format Table 2 shows the overall structure of the payload identifier. This payload identifier can only be used with 10-bit interfaces. The byte 1 value is mandatory and identifies

22、 the combination of payload format and digital interface transport. The values of the remaining 3 bytes are application specific. Default definitions for individual fields are defined in Table 3, and subsequent sections of this Recommendation. The precise definition and use of all payload identifier

23、s defined prior to 2011 is deprecated. TABLE 2 Generalized payload identifier byte definitions for digital transports Bits Byte 1 Byte 2 Byte 3 Byte 4 Bit 7 Version identifier Application specific Application specific Application specific Bit 6 Payload and digital interface Recommendations (mandator

24、y) Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TABLE 3 Suggested default payload identifier field definitions (Informative) Bits Byte 2 Byte 3 Byte 4 Bit 7 Interlaced (0) or progressive (1) transport Image aspect ratio 4:3 (0) or 16:9 (1) Channel assignment Single-link or ch1 of multi-channel (0h), ch2 of m

25、ulti-channel (1h), ch3 of multi-channel (2h), ch4 of multi-channel (3h), ch5 of multi-channel (4h), ch6 of multi-channel (5h), ch7 of multi-channel (6h) ch8 of multi-channel (7h) Bit 6 Interlaced (0) or progressive (1) picture Reserved Bit 5 Reserved Reserved Bit 4 Reserved Reserved Reserved Bit 3 P

26、icture rate Sampling structure identification Reserved Bit 2 Reserved Bit 1 Bit depth 8-bit (0h), 10-bit (1h) or 12-bit (2h), Reserved (3h) Bit 0 4 Rec. ITU-R BT.1614-1 TABLE 4 Payload identifier ancillary packet format b9 (MSB) b8 b7 b6 b5 b4 b3 b2 b1 b0 (LSB) Ancillary data flag (ADF) 0 0 0 0 0 0

27、0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Data ID (DID) not b8 EP 0 1 0 0 0 0 0 1 Secondary data ID (SDID) not b8 EP 0 0 0 0 0 0 0 1 Data count (DC) not b8 EP 0 0 0 0 0 1 0 0 Video payload (byte 1) not b8 EP Version ID Payload identifier Picture rate and scanning (byte 2) not b8 EP Application

28、 defined values and parameters Sampling structure (byte 3) not b8 EP Special options (byte 4) not b8 EP Checksum not b8 Sum of b0b8 of DID through to payload byte 4. EP = even parity for b0 through b7. 3 Placement of the ancillary data packet As this packet defines a basic payload type, the preferre

29、d horizontal placement of the ancillary data packet is immediately following an EAV-LN-CRC word sequence. The line number of the packet will vary according to the digital video interface to meet with existing equipment practice. The preferred line numbers for different interfaces are summarized belo

30、w. Implementers should be aware that the preferred horizontal and vertical locations for the Payload Identification Code packets are recommendations only. The actual packet location may vary on a case-by-case basis. Decoder manufacturers shall not depend on the recommended location for the detection

31、 and extraction of the payload packet. 3.1 1 125-line digital interfaces, interlace and segmented frame For digital interfaces having 1 125 lines with interlaced (I) and progressive segmented-frame (PsF) scanning structures, the ancillary data packet shall be added once per field on the Y-channel as

32、 Rec. ITU-R BT.1614-1 5 defined in Recommendation ITU-R BT.1120. The recommended location of the ancillary packet, if ancillary space is available, shall be on the following lines: 1 125I (field 1): Line 10 1 125I (field 2): Line 572. NOTE These line numbers also apply to Recommendation ITU-R BT.112

33、0 dual-link HD-SDI when using interlaced and progressive segmented-frame scanning. 3.2 1 125-line digital interfaces, progressive frame For digital interfaces having 1 125 lines with progressive scanning structures, the ancillary data packet shall be added once per frame on the Y-channel as defined

34、in Recommendation ITU-R BT.1120. The recommended location of the ancillary packet, if ancillary space is available, shall be on the following lines: 1 125P: Line 10. 3.3 525- and 625-line digital interfaces, interlace For digital interfaces having 525 or 625 lines with an interlaced (I) picture stru

35、cture, the ancillary data packet shall be added once per field. The recommended location of the ancillary packet, if ancillary space is available, shall be on the following lines: 525I (field 1): Line 13; 525I (field 2): Line 276; 625I (field 1): Line 9; 625I (field 2): Line 322. 4 Default values Re

36、served values shall be set to (0) unless otherwise specified in an application. This section is entirely informative. 4.1 Byte 2: Picture rate and scanning method The second byte may be used to identify the picture rate and the picture and transport scanning methods. Bit b7 may be used to identify w

37、hether the digital interface uses a progressive or interlaced transport structure such that: b7 = 0 identifies an interlaced transport; b7 = 1 identifies a progressive transport. Bit b6 may be used to identify whether the picture has a progressive or interlace structure such that: b6 = 0 identifies

38、an interlaced structure; b6 = 1 identifies a progressive structure. NOTE PsF video payloads are identified by a progressive image transported over an interlaced digital interface transport carrying the progressive image as a first and second picture segment within the transport frame duration. These

39、 first and second picture segments are indicated by the first and second field indicators in the digital interface transport. Bits b5 to b4 may be set to 0, unless defined elsewhere for application specific uses. Bits b3 to b0 may be used to identify the picture rate in Hz. 6 Rec. ITU-R BT.1614-1 TA

40、BLE 5 Suggested default assignment of picture rate values (Informative) Value Picture rate Value Picture rate Value Picture rate Value Picture rate 0h No defined value 1h Reserved 2h 24/1.001 3h 24 4h 48/1.001 5h 25 6h 30/1.001 7h 30 8h 48 9h 50 Ah 60/1.001 Bh 60 Ch Reserved Dh Reserved Eh Reserved

41、Fh Reserved 4.2 Byte 3: Sampling structure identification The third byte may be used to identify the aspect ratio and sampling structure of the video payload. Bit b7 may be used to identify the image aspect ratio such that: b7 = 0 indicates a 4:3 aspect ratio; b7 = 1 indicates a 16:9 aspect ratio. B

42、its b6 to b4 may be set to 0, unless defined elsewhere for application specific uses. Bits b3 to b0 of byte 3 may be used to identify the horizontal sampling structure. TABLE 6 Suggested default assignment of sampling structure values (Informative) Value Sampling Value Sampling Value Sampling Value

43、Sampling 0h 4:2:2 (Y/CB/CR) 1h 4:4:4 (Y/CB/CR) 2h 4:4:4 (G/B/R) 3h 4:2:0 4h 4:2:2:4 (Y/CB/CR /A) 5h 4:4:4:4 (Y/CB/CR /A) 6h 4:4:4:4 (G/B/R/A) 7h Reserved 8h 4:2:2:4 (Y/CB/CR /D) 9h 4:4:4:4 (Y/CB/CR /D) Ah 4:4:4:4 (G/B/R/D) Bh Reserved Ch Reserved Dh Reserved Eh 4:4:4 (XYZ) Fh Reserved 4.3 Byte 4: Sp

44、ecial options Byte 4 may be used to identify extended aspects of the payload appropriate to each application. Bits b7, b6 and b5 may be used to identify channel identification information such that: 0h identifies a single channel video payload or channel 1 of a multi-channel video payload; 1h identi

45、fies channel 2 of a multi-channel video payload; 2h identifies channel 3 of a multi-channel video payload; 3h identifies channel 4 of a multi-channel video payload; 4h identifies channel 5 of a multi-channel video payload; 5h identifies channel 6 of a multi-channel video payload; 6h identifies chann

46、el 7 of a multi-channel video payload; 7h identifies channel 8 of a multi-channel video payload. Rec. ITU-R BT.1614-1 7 Bits b4 to b2 may be set to 0, unless defined elsewhere for application specific uses. Bits b1 and b0 may be used to identify the bit depth of the sample quantization such that: 0h

47、 identifies quantization using 8 bits per sample; 1h identifies quantization using 10 bits per sample; 2h identifies quantization using 12 bits per sample. In the case where the bit depth field indicates 12-bits per sample, it should be noted that these bits are mapped onto a 10-bit interface. Appen

48、dix 1 (Informative) Byte 1 Registration procedure The Payload Identifier byte 1 value is assigned and registered by SMPTE RA. ITU-R Secretariat is requested to apply for byte 1 value(s) by sending a letter to the SMPTE Engineering VP requesting a Byte 1 value along with a copy of the relevant unappr

49、oved (PDNR-DNR) ITU-R Recommendation. SMPTE will assign a provisional byte 1 value following their verification that the application of the payload ID is correct. The provisional status of the byte 1 value assigned by SMPTE will remain in effect for nine months, after which the value may be reassigned. Permanent registration of the byte 1 value will be put into effect once ITU-R notifies the SMPTE Engineering VP that the relevant Recommendation is now approved. SMPTE RA will list the ITU-R registered byte1 value, and application, on the SMPTE RA web site