ITU-R P 833-8-2013 Attenuation in vegetation《植被衰减》.pdf

1、 Recommendation ITU-R P.833-8(09/2013)Attenuation in vegetationP SeriesRadiowave propagationii Rec. ITU-R P.833-8 Foreword The role of the Radiocommunication Sector is to ensure the rational, equitable, efficient and economical use of the radio-frequency spectrum by all radiocommunication services,

2、including satellite services, and carry out studies without limit of frequency range on the basis of which Recommendations are adopted. The regulatory and policy functions of the Radiocommunication Sector are performed by World and Regional Radiocommunication Conferences and Radiocommunication Assem

3、blies supported by Study Groups. Policy on Intellectual Property Right (IPR) ITU-R policy on IPR is described in the Common Patent Policy for ITU-T/ITU-R/ISO/IEC referenced in Annex 1 of Resolution ITU-R 1. Forms to be used for the submission of patent statements and licensing declarations by patent

4、 holders are available from http:/www.itu.int/ITU-R/go/patents/en where the Guidelines for Implementation of the Common Patent Policy for ITU-T/ITU-R/ISO/IEC and the ITU-R patent information database can also be found. Series of ITU-R Recommendations (Also available online at http:/www.itu.int/publ/

5、R-REC/en) Series Title BO Satellite delivery BR Recording for production, archival and play-out; film for television BS Broadcasting service (sound) BT Broadcasting service (television) F Fixed service M Mobile, radiodetermination, amateur and related satellite services P Radiowave propagation RA Ra

6、dio astronomy RS Remote sensing systems S Fixed-satellite service SA Space applications and meteorology SF Frequency sharing and coordination between fixed-satellite and fixed service systems SM Spectrum management SNG Satellite news gathering TF Time signals and frequency standards emissions V Voca

7、bulary and related subjects Note: This ITU-R Recommendation was approved in English under the procedure detailed in Resolution ITU-R 1. Electronic Publication Geneva, 2013 ITU 2013 All rights reserved. No part of this publication may be reproduced, by any means whatsoever, without written permission

8、 of ITU. Rec. ITU-R P.833-8 1 RECOMMENDATION ITU-R P.833-8 Attenuation in vegetation (Question ITU-R 202/3) (1992-1994-1999-2001-2003-2005-2007-2012-2013) Scope This Recommendation presents several models to enable the reader to evaluate the effect of vegetation on radiowave signals. Models are pres

9、ented that are applicable to a variety of vegetation types for various path geometries suitable for calculating the attenuation of signals passing through vegetation. The Recommendation also contains measured data of vegetation fade dynamics and delay spread characteristics. The ITU Radiocommunicati

10、on Assembly, considering that attenuation in vegetation can be important in several practical applications, recommends that the content of Annex 1 be used for evaluating attenuation through vegetation between 30 MHz and 60 GHz. Annex 1 1 Introduction Attenuation in vegetation can be important in som

11、e circumstances, for both terrestrial and Earth-space systems. However, the wide range of conditions and types of foliage makes it difficult to develop a generalized prediction procedure. There is also a lack of suitably collated experimental data. The models described in the following sections appl

12、y to particular frequency ranges and for different types of path geometry. 2 Obstruction by woodland 2.1 Terrestrial path with one terminal in woodland For a terrestrial radio path where one terminal is located within woodland or similar extensive vegetation, the additional loss due to vegetation ca

13、n be characterized on the basis of two parameters: the specific attenuation rate (dB/m) due primarily to scattering of energy out of the radio path, as would be measured over a very short path; 2 Rec. ITU-R P.833-8 the maximum total additional attenuation due to vegetation in a radio path (dB) as li

14、mited by the effect of other mechanisms including surface-wave propagation over the top of the vegetation medium and forward scatter within it. In Fig. 1, the transmitter is outside the woodland and the receiver is a certain distance, d, within it. The excess attenuation, Aev, due to the presence of

15、 the vegetation is given by: Aev= Am 1 exp ( d / Am) (1) where: d : length of path within woodland (m) : specific attenuation for very short vegetative paths (dB/m) Am: maximum attenuation for one terminal within a specific type and depth of vegetation (dB). FIGURE 1 Representative radio path in woo

16、dland It is important to note that excess attenuation, Aev, is defined as excess to all other mechanisms, not just free space loss. Thus if the radio path geometry in Fig. 1 were such that full Fresnel clearance from the terrain did not exist, then Aevwould be the attenuation in excess of both free-

17、space and diffraction loss. Similarly, if the frequency were high enough to make gaseous absorption significant, Aevwould be in excess of gaseous absorption. It may also be noted that Amis equivalent to the clutter loss often quoted for a terminal obstructed by some form of ground cover or clutter.

18、The value of specific attenuation due to vegetation, dB/m, depends on the species and density of the vegetation. Approximate values are given in Fig. 2 as a function of frequency. Figure 2 shows typical values for specific attenuation derived from various measurements over the frequency range 30 MHz

19、 to about 30 GHz in woodland. Below about 1 GHz there is a tendency for vertically polarized signals to experience higher attenuation than horizontally, this being thought due to scattering from tree-trunks. dAmDistance in woodland, dExcessloss(dB)AevTx RxRec. ITU-R P.833-8 3 FIGURE 2 Specific atten

20、uation due to woodland It is stressed that attenuation due to vegetation varies widely due to the irregular nature of the medium and the wide range of species, densities, and water content obtained in practice. The values shown in Fig. 2 should be viewed as only typical. At frequencies of the order

21、of 1 GHz the specific attenuation through trees in leaf appears to be about 20% greater (dB/m) than for leafless trees. There can also be variations of attenuation due to the movement of foliage, such as due to wind. The maximum attenuation, Am, as limited by scattering from the surface wave, depend

22、s on the species and density of the vegetation, plus the antenna pattern of the terminal within the vegetation and the vertical distance between the antenna and the top of the vegetation. Measurements in the frequency range 105-2 200 MHz carried out in mixed coniferous-deciduous vegetation (mixed fo

23、rest) near St. Petersburg (Russia) on paths varying in length from a few hundred meters to 7 km with various species of trees of mean height 16 m. These were found to agree on average with equation (1) with constants for specific and maximum attenuation as given in Table 1. TABLE 1 Parameter Frequen

24、cy (MHz) and polarization Frequency, MHz 105.9 Horizontal 466.475 Slant 949.0 Slant 1852.2 Slant 2117.5 Slant (dB/m) 0.04 0.12 0.17 0.30 0.34 m (dB) 9.4 18.0 26.5 29.0 34.1VH103102101011100 MHz10 MHz 10 GHz1 GHz 100 GHzV: vertical polarizationH: horizontal polarizationSpecificattenuation (dB/m)Frequ

25、ency4 Rec. ITU-R P.833-8 A frequency dependence of Am(dB) of the form: = fAAm 1(2) where f is the frequency (MHz) has been derived from various experiments: Measurements in the frequency range 900-1 800 MHz carried out in a park with tropical trees in Rio de Janeiro (Brazil) with a mean tree height

26、of 15 m have yielded A1= 0.18 dB and = 0.752. The receiving antenna height was 2.4 m. Measurements in the frequency range 900-2 200 MHz carried out in a forest near Mulhouse (France) on paths varying in length from a few hundred metres to 6 km with various species of trees of mean height 15 m have y

27、ielded A1= 1.15 dB and = 0.43. The receiving antenna in woodland was a /4 monopole mounted on a vehicle at a height of 1.6 m and the transmitting antenna was a /2 dipole at a height of 25 m. The standard deviation of the measurements was 8.7 dB. Seasonal variations of 2 dB at 900 MHz and 8.5 dB at 2

28、 200 MHz were observed. Measurements in the frequency range 105.9-2 117.5 MHz carried out in two forest-park areas with coniferous-deciduous vegetation (mixed forest) in St. Petersburg (Russia) with a tree height of 12 to 16 m and average distance between them was approximately 2 to 3 m, that corres

29、ponds to the density of 20-10 tree/100 m2have yielded A1= 1.37 dB and = 0.42. To receive the signal, a quarter-wave length dipole antenna at 1.5 m above the ground level was used. The distance between the receiver and the transmitter antenna was 0.4 to 7 km, and paths for measurement were chosen so

30、as to have line-of-sight between these antennas without any obstacles but only the woodland to be measured. Different phases of the experiment were performed in similar weather conditions: dry weather, wind speed 0 to 7 m/s. 2.2 Satellite slant paths Representative radio path in woodland: In Fig. 3,

31、 Transmitter (TX) and Receiver (RX) are outside the woodland. The relevant parameters are: vegetation path length, d; average tree height, hv; height of the Rx antenna over ground, ha; radio path elevation, ; distance of the antenna to the roadside woodland, dw. Rec. ITU-R P.833-8 5 FIGURE 3 Represe

32、ntative radio path in woodland with vegetation path length, d, average tree height, hv, height of the Rx antenna over ground, ha, radio path elevation, , and distance of the antenna to the roadside woodland, dwTo describe the attenuation loss, L along both, horizontal and slant foliage path propagat

33、ion, the following model is proposed: L(dB) = A f Bd C ( + E)G(3) where: f: frequency (MHz) d: vegetation depth (m) : elevation (degrees) A, B, C, E, and G: empirical found parameters. A fit to measurements made in pine woodland in Austria gave: L(dB) = 0.25 f 0.39d 0.25 0.05 (4) 3 Single vegetative

34、 obstruction 3.1 At or below 1 GHz Equation (1) does not apply for a radio path obstructed by a single vegetative obstruction where both terminals are outside the vegetative medium, such as a path passing through the canopy of a single tree. At VHF and UHF, where the specific attenuation has relativ

35、ely low values, and particularly where the vegetative part of the radio path is relatively short, this situation can be modelled on an approximate basis in terms of the specific attenuation and a maximum limit to the total excess loss: = dAet(5) where: d : length of path within the tree canopy (m) :

36、 specific attenuation for very short vegetative paths (dB/m) and Aet : lowest excess attenuation for other paths (dB). dwRxhadTxhv6 Rec. ITU-R P.833-8 The restriction of a maximum value for Aetis necessary since, if the specific attenuation is sufficiently high, a lower-loss path will exist around t

37、he vegetation. An approximate value for the minimum attenuation for other paths can be calculated as though the tree canopy were a thin finite-width diffraction screen using the method of Recommendation ITU-R P.526. It is stressed that equation (5), with the accompanying maximum limit on Aet, is onl

38、y an approximation. In general it will tend to overestimate the excess loss due to the vegetation. It is thus most useful for an approximate evaluation of additional loss when planning a wanted service. If used for an unwanted signal it may significantly underestimate the resulting interference. 3.2

39、 Above 1 GHz For terrestrial paths, the method based on RET described in 3.2.1 should be applied to compute the effect of a single tree. For slant paths, the method based on multiple scattering theory described in 3.2.2 should be applied to compute the effect of a single tree. 3.2.1 Terrestrial path

40、 In order to estimate the total field, the diffracted, ground reflected and through-vegetation scattering components are first calculated and then combined. The diffracted components consist of those over the top of the vegetation and those around the sides of the vegetation. These components and th

41、e ground reflected component are calculated using ITU-R Recommendations. The through or scattered component is calculated using a model based upon the theory of radiative energy transfer (RET). 3.2.1.1 Calculation of the top diffracted component The diffraction loss, Ltop, experienced by the signal

42、path diffracted over the vegetation, may be treated as double isolated knife-edge diffraction for the geometry defined in Fig. 4. FIGURE 4 Component diffracted over top of vegetation This is calculated as follows: )()(_+=RxTxdifftoptopGGLL (6) Rec. ITU-R P.833-8 7 where GTx() and GRx() are the losse

43、s due to angles of the diffracted wave leaving the transmit antenna and coming into the receive antenna, respectively. Ltop_diff is the total diffraction loss as calculated using the method of Recommendation ITU-R P.526 for double isolated edges. 3.2.1.2 Calculation of the side diffracted component

44、The diffraction loss, Lsideaand Lsideb, experienced by the signal diffracted around the vegetation, may again be treated as double isolated knife-edge diffraction, for the geometry defined in Fig. 5. FIGURE 5 Components diffracted around the vegetation The losses are calculated using equations (7) a

45、nd (8). )()(_ aRxaTxsideadiffsideaGGLL += (7) and )()(_ bRxbTxsidebdiffsidebGGLL += (8) where GTx(a,b) and GRx(a,b) are the losses due to angles of the diffracted wave leaving the transmit antenna and coming into the receive antenna, for sides a and b, respectively. Ldiff_sideaand Ldiff_sidebare the

46、 total diffraction loss around each side found using the method of Recommendation ITU-R P.526 for double isolated edges. 3.2.1.3 Calculation of the ground reflected component It is assumed that the path is sufficiently short that the ground reflected wave may be modelled by the geometry shown in Fig

47、. 6. baabSide bSide a8 Rec. ITU-R P.833-8 FIGURE 6 Ground reflected component To calculate the loss experienced by the ground reflected wave at the receiver, the reflection coefficient, R0, of the ground reflected signal may be calculated with a given grazing angle, g. This is a standard method and

48、is described in Recommendation ITU-R P.1238. The values for the permittivity and conductance are obtained from Recommendation ITU-R P.527. The loss experienced by the ground reflected wave, Lground, is then given by: )()()(log20log2001002110+ +=RxTxgroundGGRdddL (9) where GRx() and GTx() are the los

49、ses due to angles of the reflected wave leaving the transmit antenna and coming into the receive antenna, respectively. 3.2.1.4 Calculation of the “through” or scattered component In order to make accurate predictions of the excess attenuation to vegetation the user needs to input the following parameters into the RET equation (equation (10): : ratio of the forward scattered power to the total scattered power : beamwidth of the phase function (degrees) : combined absorption and scatter coef