ImageVerifierCode 换一换
格式:PDF , 页数:8 ,大小:233.88KB ,
资源ID:794091      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-794091.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ITU-R SM 1792-2007 Measuring sideband emissions of T-DAB and DVB-T transmitters for monitoring purposes《监测目的的T-DAB和DVB-T发射机的测量边带发射》.pdf)为本站会员(appealoxygen216)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ITU-R SM 1792-2007 Measuring sideband emissions of T-DAB and DVB-T transmitters for monitoring purposes《监测目的的T-DAB和DVB-T发射机的测量边带发射》.pdf

1、 Rec. ITU-R SM.1792 1 RECOMMENDATION ITU-R SM.1792 Measuring sideband emissions of T-DAB and DVB-T transmitters for monitoring purposes (2007) Scope This Recommendation provides guidance to measurement procedures and specifies settings in measuring emissions of terrestrial digital audio broadcasting

2、 (T-DAB) and digital video broadcasting-terrestrial (DVB-T) for conformity with the relevant spectrum masks. The ITU Radiocommunication Assembly, considering a) that Recommendation ITU-R BS.1660 gives definitions of spectrum masks specifying limits for out-of-band (OoB) domain emissions of T-DAB (te

3、rrestrial digital audio broadcasting) transmitters; b) that Annex 2 of the Final Acts of RRC-06 gives definitions of spectrum masks specifying limits for OoB domain emissions of DVB-T (digital video broadcasting-terrestrial) transmitters; c) that the potential of imposing harmful interference to adj

4、acent radio services from T-DAB and DVB-T emissions is especially high due to their rectangular spectrum shape which places the maximum signal level up to the edges of the assigned bandwidth; d) that monitoring stations have to measure the conformance with the relevant masks for any T-DAB or DVB-T t

5、ransmitter, preferably off-air, to protect adjacent radio services from harmful interference; e) that the dynamic range of spectrum analysers is not sufficient to measure the OoB emissions from these transmitters, recommends 1 that, when measuring conformance of T-DAB and DVB-T emissions with the re

6、levant spectrum masks, the method described in Annex 1 should be used. Annex 1 1 Spectrum masks To protect neighbouring radio services, spectrum masks are defined in the vicinity of the main emission. The level of any OoB and spurious emission has to be lower than the mask. 1.1 T-DAB For T-DAB trans

7、mitters, Recommendation ITU-R BS.1660 defines the following spectrum masks: 2 Rec. ITU-R SM.1792 FIGURE 1 OoB emissions from T-DAB transmitters Note The critical mask is to be used for the lowest and highest channel in the allocated band to protect neighbouring radio services, the uncritical mask is

8、 to be used inside the allocated band. Uneven frequency breakpoints are 0.77 MHz, 0.97 MHz, 1.75 MHz and 2.2 MHz. The mask assumes a 4 kHz measurement filter. 1.2 DVB-T For DVB-T transmitters, Annex 2 to the Final Acts of RRC-06 defines spectrum masks for DVB-T systems. As an example, Fig. 2 shows t

9、he mask for 8 MHz channel width. 2 Measurement of sideband emissions from T-DAB and DVB-T transmitters12.1 General as to be seen from Figs. 1 and 2, the maximum level of sideband emissions from T-DAB and DVB-T transmitters may go down to a level of 101 dB, compared to the maximum power in the assign

10、ed channel, measured with the same receiver bandwidth. To reliably measure true sideband emissions, the measurement equipment has to have a dynamic range of at least 110 dB. The dynamic range of modern monitoring receivers or spectrum analysers of around 80 dB is not sufficient to directly measure c

11、onformance with the masks. 1Measurements for T-DAB can also be used for other systems, e.g. terrestrial digital multimedia broadcasting (T-DMB) (see Report ITU-R BT.2069). Rec. ITU-R SM.1792 3 FIGURE 2 OoB emissions from 8 MHz DVB-T transmitters Note The critical mask is to be used for the lowest an

12、d highest channel in the allocated band to protect neighbouring radio services, the uncritical mask is to be used inside the allocated band. Uneven frequency breakpoints are 3.8 MHz and 4.2 MHz. The mask assumes a 4 kHz measurement filter. 2.2 Measurement principle To increase the dynamic range of t

13、he measurement receiver, the T-DAB or DVB-T signal has to be passed through a filter that suppresses the main signal and passes the OoB domain. The signal including one sideband in the OoB domain is scanned through this filter with a narrow resolution bandwidth (RBW) and the resulting spectral level

14、s are recorded. In a second scan, the frequency response of the filter (attenuation) is recorded for the same frequency range. The filter attenuation is then added to the spectral levels from the first scan to give the true, unfiltered spectrum. The achievable gain in measurement dynamics only depen

15、ds on the sharpness of the filter. 2.3 Measurement set-up Various different set-ups are possible to perform sideband measurements according to the described measurement principle. The following set-up is a version with separate units for receiver, filter and measurement controller: 4 Rec. ITU-R SM.1

16、792 FIGURE 3 Example of measurement set-up For the measurement set-up above, the following requirements apply: TABLE 1 Requirements for example measurement set-up Item Function, requirement, remarks Attenuator To adjust the input level of the T-DAB/DVB-T signal to the maximum that the receiver can h

17、andle without being overloaded. Adjustment steps: 1 dB Filter To suppress the main T-DAB/DVB-T signal while bypassing the sideband emissions. Can be a bandpass or notch filter. If a bandpass filter is used, the minimum 3 dB bandwidth has to be 8 MHz for DVB-T and 2 MHz for T-DAB measurements. The fi

18、lter has to be tunable inside the desired frequency range Receiver To record the spectral levels. It must be equipped with a tracking generator and an interface to allow remote control and data readout. RBW has to be between 3 kHz and 8 kHz (preferably 4 kHz). Detector: preferably RMS, alternatively

19、 AV Computer To control the receiver and read out level data. It has to be equipped with a suitable interface to connect to the receiver (e.g. LAN or IEEE 488) Among others, the following alternative measurement configurations are also possible: All units can be included in one device that is especi

20、ally designed to perform automatic or semi-automatic measurements of T-DAB/DVB-T sideband emissions. The receiver can be a spectrum analyser. The receiver/analyser can include the functions of the computer. An external signal generator can be used instead of the built-in tracking generator. The freq

21、uency of the signal generator has to be controlled by the computer in sync with the receiver/analyser. 2.4 Measurement procedure To clarify the measurement procedure below, we use an example where we want to measure the upper sideband of an 8 MHz wide DVB-T signal transmitting on 650 MHz. Rec. ITU-R

22、 SM.1792 5 2.4.1 Ensuring reflection-free signal reception Measurement of the sideband emissions of T-DAB/DVB-T signals can either be made at the test output of the transmitter or off the air. To ensure enough signal level when measuring off-air, a measurement location in the main beam, close to the

23、 transmitter, is selected. However, even if there is free line-of-sight to the transmit antenna, reflections can cause frequency-selective distortion of the signal. For the sideband measurement it is necessary to have a reflection-free reception of the T-DAB/DVB-T signal. To ensure this, the signal

24、is either displayed on a spectrum analyser, or manually scanned using the receiver. The flatness of the main T-DAB/DVB-T signal should be within 2 dB. 2.4.2 Determining the maximum signal level In a first test, the maximum level of T-DAB/DVB-T signal that the receiver can handle without being overlo

25、aded has to be measured. This level cannot be taken out of the receiver specifications because they only specify the dynamic range for unmodulated carriers. For broadband modulated signals such as T-DAB or DVB-T, the maximum level is considerably lower. To determine it, the T-DAB/DVB-T signal is con

26、nected to the receiver (without the filter, switch 2 in Fig. 3 closed), but after the adjustable attenuator. The receiver is adjusted to the same RBW and detector as for the actual measurement (e.g. 3 kHz RMS). IF and RF attenuation have to be set to 0 dB. If present, a preamplifier has to be switch

27、ed on. The most critical frequency range where receiver overloading takes place is the range just outside the “edge” frequencies of the T-DAB/DVB-T block. TABLE 2 “Edge” frequencies of T-DAB and DVB-T emissions System/bandwidth “Edge” frequency (offset from centre frequency) T-DAB/1.5 MHz 775 kHz DV

28、B-T/7 MHz 3.3 MHz DVB-T/8 MHz 3.8 MHz The receiver is tuned to a frequency 100 kHz above the upper or 100 kHz below the lower edge frequency, depending on the sideband to be measured. In our measurement example (see 2.4), this frequency would be 650 MHz + 3.8 MHz + 100 kHz = 653.9 MHz. Using the adj

29、ustable attenuator, the signal is adjusted to a level just below that which overloads the receiver. This can be verified by changing the attenuation 1 dB up and down. When the receiver is not overloaded, the indicated level also rises or falls by exactly 1 dB. The minimum attenuation that ensures th

30、is behaviour has to be found. With this attenuator setting, the receiver is tuned to the T-DAB/DVB-T centre frequency. The indicated level is noted as the “maximum receive level”. 2.4.3 Tuning the filter To increase the dynamic range for the measurement, the filter is used to provide the necessary a

31、ttenuation of the main T-DAB/DVB-T signal instead of the attenuator used in 2.4.2. To adjust the filter frequency, the receiver is tuned to a frequency just inside the edge frequency. In our example (see 2.4), this frequency would be just below 653.8 MHz (650 MHz + 3.8 MHz). 6 Rec. ITU-R SM.1792 Thi

32、s is the frequency where the receiver will get the maximum level during the actual measurement. The filter is now tuned in such a way that the indicated level is equal to the maximum receive level determined in 2.4.2, and the filter attenuation increases towards the centre frequency of the T-DAB/DVB

33、-T emission. Figure 4 shows the filter tuning for our measurement example. FIGURE 4 Filter tuning for measurement example If a notch filter is used, it is also adjusted in such a way that the receive level at the edge frequency measured in 2.4.2 is not exceeded, starting from the T-DAB/DVB-T centre

34、frequency. 2.4.4 Determining the receiver noise level Because the actual measurement cannot distinguish between the noise-like sideband emissions of the T-DAB/DVB-T transmitter and receiver noise, it is important to know the receiver noise level. To measure it, the receiver is again adjusted to the

35、same RBW and detector as for the actual measurement (e.g. 3 kHz RMS). IF and RF attenuations have to be set to 0 dB. If present, a preamplifier has to be switched on. The signal is disconnected and the receiver input is terminated with 50 . The indicated receive level is noted as the receiver noise

36、level. 2.4.5 Performing the actual measurement Using the set-up in Fig. 3, the computer program is started to scan the relevant frequency range. The measurement has to start well inside the main T-DAB/DVB-T channel in order to have a reference for the spectrum masks. The stop frequency depends on th

37、e end on the spectrum mask definition and the passband range of the filter. In our example (see 2.4), we start recording 2 MHz off the DVB-T centre frequency at 652 MHz and stop at 662 MHz, which is the end of the spectrum mask definition (see Fig. 2). The measured spectral levels are recorded in a

38、file, together with the current receiver frequency. Then, the tracking generator is connected to the receiver input (S1 in Fig. 3 to position 2) and the scan is repeated for the same frequency range. The measured attenuation is recorded in a second file, together with the current receiver frequency.

39、 Rec. ITU-R SM.1792 7 2.4.6 Presentation of the results The computer has to add the measured level from file 1 and the attenuation from file 2 for each frequency step. The result is the actual spectrum of the T-DAB/DVB-T signal with eliminated filter distortion. For quick evaluation, the relevant sp

40、ectrum masks from Figs. 1 and 2 should be included in the graphical presentation. Because usually the filter can only be optimized for either the upper or lower sideband, two separate measurements have to be performed if full compliance with the spectrum mask has to be checked. The following is a po

41、ssible result of the measurement from our example (see 2.4). A common spreadsheet program has been used to control the receiver and draw the graphics using a macro language. FIGURE 5 Result graph for measurement example It can be seen that the critical mask is exceeded from 660 MHz on. 2.4.7 Conside

42、ring the system sensitivity Especially far from the T-DAB/DVB-T centre frequency, spectral levels from the transmitter will be very weak and may fall at or below the receiver noise level. Because the result presentation does not allow distinguishing between transmitter sideband emissions and receive

43、r noise, the limits within which the measurement is valid have to be established manually. For a reasonably reliable result, the spectral level of transmitter sideband emissions, received through the filter, has to be at least 3 dB above the receiver noise. The system sensitivity is the noise level

44、measured in 2.4.4, 8 Rec. ITU-R SM.1792 increased by the filter attenuation at each frequency within the scan range. It is preferable to include the system sensitivity in the presentation graph like in Fig. 5. In our measurement example, the 3 dB margin between measured signal level and system sensi

45、tivity is reached at around 662 MHz. The validity range of the measurement has to be clearly indicated in the presentation graph, either by marking the respective frequencies or by scaling the x-axis in a way that only valid results are displayed, like in Fig. 5. 2.5 Practical considerations Althoug

46、h in principle the method described here allows sideband emission measurements for all T-DAB and DVB-T transmitters, there are a few aspects that have to be considered: The adverse requirements for the filter to be both steep and easily tunable result in a compromise. Experience shows that with band

47、pass filters having a 3 dB width of 1% of the tuned frequency are suitable to evaluate even the critical mask of T-DAB/DVB-T emissions up to about 800 MHz. At the same time, they can be tunable with only one knob, because all cavities can be mounted on the same axis. The most difficult part when per

48、forming sideband measurements is to get enough signal level from the receiving antenna. Again, experience shows that only the non-critical spectrum masks can be evaluated off-air. Even then, a directional antenna with high gain, such as a yagi, has to be used and placed in the optimal distance to th

49、e transmitter where maximum field strength can be expected. To evaluate the critical masks, the measurement has to be performed at the test output of the transmitter itself. Due to the very limited choice of optimal receiving places, this measurement usually has to be performed in mobile monitoring units. Stationary or remote-controlled equipment will not receive enough field strength in most cases.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1