ITU-T T 522-1992 Communication Application Profile BT1 for Document Bulk Transfer (Study Group VIII) 7 pp《文件批量传送的通信应用轮廓BT1(研究组8)7页》.pdf

1、INTERNATIONAL TELECOMMUNICATION UN ION CCITT THE INTERNATIONAL TELEGRAPH AND TELEPHONE CONSULTATIVE COMMITTEE T.522 (09/92) TERMINAL EQUIPMENT AND PROTOCOLS FOR TELEMATIC SERVICES COMMUNICATION APPLICATION PROFILE BTI FOR DOCUMENT BULK TRANSFER Recommendation T.522 CCITT RECMNrT.522 92 m 4862571 057

2、6683 723 m FOREWORD The CCIT (the International Telegraph and Telephone Consultative Committee) is a permanent organ of the International Telecommunication Union (ITU). CCIT is responsible for studying technical, operating and tariff questions and issuing Recommendations on them with a view to stand

3、ardizing telecommunications on a worldwide basis. The Plenary Assembly of CCIT which meets every four years, establishes the topics for study and approves Recommendations prepared by its Study Groups. The approval of Recommendations by the members of CCITT between Plenary Assemblies is covered by th

4、e procedure laid down in CCITT Resolution No. 2 (Melbourne, 1988). Recommendation T.522 was revised by Study Group VI11 and was approved under the Resolution No. 2 procedure on the 18th of September 1992. CCIT NOTE In this Recommendation, the expression “Administration“ is used for conciseness to in

5、dicate both a telecommunication administration and a recognized private operating agency. O IT 1993 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writin

6、g from the IT. CONTENTS O Introduction 1 2 References 3 Definitions 4 Abbreviations and conventions 5 Scope and field of application Definition of communication application profile BTl 5.1 Overview of BTl 5.2 DTAM functional units 5.3 DTAM service primitives and parameters INTRODUCTION T.400-Series

7、Recommendations define the open document architecture (T.4 10-Series Recommendations) and the DTAM services and protocols (T.430-Series Recommendations) for the purpose of the document transfer and manipulation. In order to apply T.400-Series Recommendations to various telematic services, it is nece

8、ssary to specify the DTAM application profile for each service that consists of a document application profile and a communication application profile. According to this requirement, T5OO-Series Recommendations define the document application profiles and T.520-Series Recommendations define the comm

9、unication application profiles. Recommendation T.522 is one of a set of T.520-Series Recommendations to define the communication application profile for the document bulk transfer using X.200 environment. Recommendation T.522 COA4MUNICATION APPLICATION PROFILE BT1 FOR DOCUMENT BULK TRANSFER (revised

10、 1992) 1 Scope and field of application This Recommendation defines the communication application profile for the document bulk transfer in a) DTAM functional units used; b) terms of DTAM service primitives and parameters used. Recommendation T.522 (09192) 1 CCITT RECMN*T-522 92 m 4862571 0576683 7T

11、b m 2 References Recommendation. The following references are required in order to implement the communication profile defined in this CCITT Recommendation T.431, Document transfer and manipulation (DTAM) - Service and protocols -Introduction and general principles. CCITT Recommendation T.432, Docum

12、ent transfer and manipulation (DTAM) - Service protocols - Service definition. - - - CCIT Recommendation T.433, Document transfer and manipulation (DTAM) - Service and protocols - Protocol specif cation. 3 Definitions The definitions of T.400-Series Recommendations also apply to this Recommendation.

13、 4 Abbreviations and conventions The abbreviations and conventions defined in TAOO-Series Recommendations also apply to this Recommendation. 5 Definitions of communication application profide BT1 5.1 Overview of BTl Recommendation T.43 1. This Recommendation defines functional units and communicatio

14、n support function in accordance with BTl uses the document bulk transfer in normal mode (RTSE) as defined in Recommendation T.433. 5.2 DTAM functional irnits The following functional units defined in Recommendation T.432 are used for BT1: - association use control (kernel); - capability; - document

15、 bulk transfer; - token control. 5.3 DTAM service primitives and parameters General DTAM service definition and parameters are defined in Recommendation T.432. This section specifies the parameters of DTAM service of BT1. 5.3.1 D-INITIATE service parameters The foliowing parameters of this service -

16、 telematic requirements; and - application capabilities, are used as follows (See Table 1L.522.). 1) Telematic requirements The following functional units defined in Recommendation T.432 are used for BT1 as mandatory functional units: - association control (kernel); - document bulk transfer; 2 Recom

17、mendation T.522 (09/92) - token control; - capability. 2) Application capabilities are used This “application capabilities” is defined in Recommendation T.432 and the following sub-parameters - ODA Application capabilities a) Document application profile This parameter is used as defined in Recommen

18、dation T.432. b) Non-basic document characteristics This is the “non-basic document characteristics7 defined in Recommendation T.432. c) Non-basic structure characteristics This is the “non-basic structure characteristics” defined in Recommendation T.432. - File transfer capabilities a) BFT capabili

19、ties This parameter is used as defined in Recommendation T.432. b) Transparent data capability This parameter is used as defined in Recommendation T.432. The Transparent mode service parameter is not used. The other service parameters are used as defined in Recommendation T.432. TABLE 1R.522 Usage o

20、f theTelematic requirements and Application Capabilities service parameters for BT1 Telematic requirements Application capabilities - ODA application capabilities Document Application profile Non-basic document characteristics Non-basic structure characteristics - File transfer capabiIities BFT capa

21、bilities Transparent data capability D-INITIATE request M M M U U U U D-INITIATE indication D-INITIATE response M M M U U U U 5.3.2 D-TERMINATE service parameters This service has no parameter for BT1. Only the initiator can issue D-TERMINATE. In addition, the initiator can issue D-TERMINATE only if

22、 he has the data token. Recommendation T.522 (09192) 3 CCITT RECMN*T.522 92 m Y862591 0576685 579 m 5.3.3 D-U-ABORT service parameters This service has the parameter of “user information”. This parameter is used as defined in Recommenda- tion T.432. 5.3.4 D-CAPABIUTY service parameters The following

23、 parameter of this service is as follows: - Application capabilities This “application capabilities” is defined in Recommendation T.432 and the following sub-parameters are used - ODA application capabilities a) Document application profile This parameter is used as defined in Recommendation T.432.

24、b) Non-basic document characteristics This is the “non-basic document characteristics” defined in Recommendation T.432. c) Non-basic structure characteristics This is the “non-basic structure characteristics” defined in Recornmendation T.432. - File transfer capabilities a) BFT capabilities This par

25、ameter is used as defined in Recommendation T.432. b) Transparent data capability This parameter is used as defined in Recommendation T.432. (See Table 2D.522.) TABLE 2fl.522 Usage of the Application capabilities service parameter for BT1 Application capabilities - ODA Application capabilities Docum

26、ent application profile Non-basic document characteristics Non-basic structure characteristics - File transfer capabilities RFT capabilities Transparent data capability D-CAPABILITY request M M U U U U D-C APABILITY indication D-CAPABILITY response M M U U U U D-CAPABILITY confirm 4 Recommendation T

27、.522 (09192) - _ CCITT RECNN*T.522 72 m 4862593 0576686 405 m 5.3.5 D-TRANSFER service parameters This D-TRANSFER service is used as defined in Recommendation T.432. 5.3.6 D-CONTROL GIVE service parameters This parameter is used as defined in Recommendation T.432. 5.3.7 D-TOKEN PLEASE service parame

28、ters The D-TOKEN PLEASE service is used to request the data token. The service has the parameter priority as defined in Recommendation T. 432. BT1 uses the value two (normal priority). Note -Whether a D-CONTROL GIVE request is issued as an answer to a D-TOKEN request is a user option. Recommendation T.522 (09/92) 5