JEDEC JESD482-A-1984 List of Preferred Values for Use on Various Types of Small Signal and Regulator Diodes《在各种类型小型信号和调整起二极管中使用的首选值清单》.pdf

1、JEDEC STANDARD List of Preferred Values for Use on Various Types of Small Signal and Regulator Diodes JESD482-A (Revision of EIA-482) AUGUST 1984 (Reaffirmed: APRIL 1999, APRIL 2002) JEDEC SOLID STATE TECHNOLOGY ASSOCIATION NOTICE JEDEC standards and publications contain material that has been prepa

2、red, reviewed, and approved through the JEDEC Board of Directors level and subsequently reviewed and approved by the JEDEC legal counsel. JEDEC standards and publications are designed to serve the public interest through eliminating misunderstandmgs between manufacturers and purchasers, facilitating

3、 interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for use by those other than JEDEC members, whether the standard is to be used either domestically or internationally. JEDEC standards and publications are ado

4、pted without regard to whether or not their adoption may involve patents or articles, materials, or processes. By such action JEDEC does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the JEDEC standards or publications. The information i

5、ncluded in JEDEC standards and publications represents a sound approach to product specification and application, principally from the solid state device manufacturer viewpoint. No claims to be in conformance with this standard may be made unless all requirements stated in the standard are met. Inqu

6、iries, comments, and suggestions relative to the content of this JEDEC standard or publication should be addressed to JEDEC at the address below, or call (703) 907-7559 or www.jedec.org Published by OJEDEC Solid State Technology Association 2002 2500 Wilson Boulevard Arlingtn, VA 22201-3834 This doc

7、ument may be downloaded free of charge; however JEDEC retains the copyright on this material. By downloadmg this file the individual agrees not to charge for or resell the resulting material. PRICE: Please refer to the current Catalog of JEDEC Engineering Standards and Publications or call Global En

8、gineering Documents, USA and Canada 1-800-854-7179, International (303) 397-7956 Printed in the U.S.A. All rights reserved PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by JEDEC and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited numb

9、er of copies through entering int a license agreement. For informatioq contact: JEDEC Solid State Technology Association 2500 Wilson Boulevard Arlingtq Virginia 2220 1 - 3 8 34 or call (703) 907-7559 RS-482-A “ Th i LIST OF PREFERRED VALUES FOR USE ON VARIOUS TYPES OF SMALL SIGNAL AND REGULATOR DIOD

10、ES Standard contains the major technical contents of Inter ti Electro teciin ical Commission Pub1 icat ion #63. If differs from na1 I EC Publication #63 in certain important respects, as given in Appendix A. These differences have been called to the attention of the U.S. Committee of Experts for IEC

11、 Technical Committee 47, and resolution of these differences will be sought in future meetings of TC47.“ RS-482-A Page 1 LIST OF PREFERRED VALUES FOR USE ON VARIOUS TYPES OF SMALL SIGNAL AND REGULATOR DIODES (From Standards Proposal No . 1624, formulated under the cognizance of EIA/JEDEC JC-22.4 Sub

12、committee on Voltage Regulators and Signal Diodes. 1 1.0 INTRODUCTION In the manufacture and application of diodes it is desirable to standardize the nominal values when specifying breakdown voltage for voltage regulator diodes, capacitance for variable capacitor diodes, and peak point current for t

13、unnel diodes. 2.0 SCOPE 2.1 Preferred breakdown voltage values for voltage regulator diodes. 2.2 Preferred values of capacitance for variable capacitor diodes. 2.3. Preferred values of peak point current for tunnel diodes . 3.0 DISCUSSION 3.1 The list shown on page 2 contains preferred nominal value

14、s along with tolerance limits at 5, 10 and 20%. These values should be used as follows: (a) In specification of voltage regulator diode breakdown voltages. (b) As values of capacitance for variable capacitor d i odes. (c) AS values of peak point current for tunnel diodes. 3.2 It should be noted that

15、 the tolerance limits are not in all cases at exactly the 5, 10 or 20% values. These limits have been rounded to avoid gaps in the list of values; as well as to provide for some overlap These values are all considered to be multiplied by 10 where n is a positive or negative integer. Thus, the series

16、 is applicable over all decades. RS-482-A Page 2 Nominal Approx. 5% Values Rounded 10% Values Minimum Maximum Minimum Maximum 1.0 .940 1.060 -90 1.10 1.1 1.040 1.160 1.00 1.20 1.2 1.140 1.270 1*10 1.30 1.3 1.240 1.410 1.15 1.45 1.5 1.38&1 1.580 1.35 l,65 1.6 1.530 1,710 1.45 1.75 1.8 1.680 1,910 1.6

17、0 2.00 2.0 1 . 880 2.120 1.% 2.20 2.2 2.080 2.330 2*0g 2.40 2.4 2.180 2.560 2.15 2.65 2.7 2.510 2.890 2.40 3.00 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 2.800 3-10kI 3.400 3.700 4.000 4.4016 4.800 5.200 3.200 3.500 3.800 4*100 4.600 5.000 5.4pI0 6.000 2.70 3. !J0 3.2 3.50 3.90 4.20 4.60 5.00 3.30 3.60 4.00 4

18、.30 4.70 5.20 5.60 6.20 6.2 5,800 6.600 5.6u 6.8 .8 6.400 7.200 6.10 7.50 7.5 7.000 7.900 6.80 8.20 8.2 7.700 8 . 700 7.40 9.00 9.1 8.500 9.600 8.20 10.00 Rounded 2ff% Valu83 Minimum Maximum -80 1.20 .90 1-30 .95 1.45 1*05 1.55 1.20 1.80 1.30 1.90 1.40 2.20 1.6ff 2.40 1-80 I 6B 1.90 2.90 3,20 2.20 2

19、.40 2.60 2.90 3.1a 3.40 4.10 4.50 3.80 3,6!J 4-0 4.30 4.?0 Ei, 20 5.60 6.10 6.70 5.00 7.4 5.40 8.20 6.00 9.00 9.80 6.60 7.30 10.90 NOTE: i values times inn where n is an integer. s-48 Page 3 APPENDIX A in addition to nominal values provided in IEC Publication #63, RS- 482-A lists the associated mini

20、mum and maximum of each nominal listed for 5%, 10%, and 20% tolerances. All nominals listed for 5% are retained for the 108 and 20% in RC-482-A, whereas IEC #63 deletes select nominals as the tolerances are expanded. It should be noted that the approximated 5% tolerances listed in RS-482-A were copied from existing pro-electron registrations of zener diodes.