NA to BS EN 1994-2-2005 UK National Annex to nEurocode 4 Design of ncomposite steel and nconcrete structures – nPart 2 General rules and rules for bridges《欧洲法规4的英国国家附录.pdf

1、NA to BS EN 1994-2:2005UK National Annex to Eurocode 4: Design of composite steel and concrete structures Part 2: General rules and rules for bridgesICS 91.010.30; 91.080.10; 91.080.40; 93.040NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWNATIONAL ANNEXLicensed Copy: Wang Bin,

2、 ISO/EXCHANGE CHINA STANDARDS, 24/03/2008 07:27, Uncontrolled Copy, (c) BSIPublishing and copyright informationThe BSI copyright notice displayed in this document indicates when the document was last issued. BSI 2007ISBN 978 0 580 54983 0The following BSI references relate to the work on this standa

3、rd:Committee reference B/525/4Draft for comment 06/30128176 DCPublication historyFirst published December 2007Amendments issued since publicationAmd. no. Date Text affectedNA to BS EN 1994-2:2005Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 24/03/2008 07:27, Uncontrolled Copy, (c) BSI BSI 2

4、007 1NA to BS EN 1994-2:2005National Annex (informative) to BS EN 1994-2:2005, Eurocode 4: Design of composite steel and concrete structures Part 2: General rules and rules for bridgesIntroductionThis National Annex has been prepared by BSI Subcommittee B/525/4, Composite structures. In the UK it is

5、 to be used in conjunction with BS EN 1994-2:2005.NA.1 ScopeThis National Annex gives:a) the UK decisions for the Nationally Determined Parameters:1) in the general rules described in the following subclauses of BS EN 1994-2:2005, which come from BS EN 1994-1-1:2004:2) in the specific rules for brid

6、ges described in the following subclauses of BS EN 1994-2:2005:NOTE See foreword to EN 1994-2:2005.b) the UK decision on the status of BS EN 1994-2:2005, informative Annex C; andc) references to non-contradictory complementary information. NA.2 Nationally Determined ParametersNA.2.1 Reference to gui

7、dance for shear connectors other than welded headed studs BS EN 1994-2:2005, 1.1.3 (3)Guidance for shear connectors other than welded headed studs is given in PD 6696-2. 2.4.1.1 (1) 2.4.1.2 (5)P 6.6.3.1 (1) 1.1.3 (3) 6.6.1.1 (13) 2.4.1.2 (6)P 6.8.1 (3) 5.4.4 (1) 6.8.2 (1) 6.2.1.5 (9) 7.4.1 (4) 6.2.2

8、.5 (3) 7.4.1 (6) 6.3.1 (1) 8.4.3 (3)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 24/03/2008 07:27, Uncontrolled Copy, (c) BSINA to BS EN 1994-2:20052 BSI 2007NA.2.2 Partial factor for pre-stressing action, PBS EN 1994-2:2005, 2.4.1.1 (1)The partial factor for pre-stressing action, P, shoul

9、d be 1,0 for favourable and unfavourable effects, as recommended in BS EN 1994-2.NA.2.3 Partial factor for design shear resistance of a headed stud, V BS EN 1994-2:2005, 2.4.1.2 (5)PThe partial factor for design shear resistance of a headed stud, V, should be 1,25 as recommended in BS EN 1994-2.NA.2

10、.4 Partial factor for fatigue strength of studs in shear, Mf,s BS EN 1994-2:2005, 2.4.1.2 (6)PThe partial factor for fatigue strength of studs in shear, Mf,s, should be 1,0 as recommended in BS EN 1994-2.NA.2.5 Combination factor for global and local action effects BS EN 1994-2:2005, 5.4.4 (1)The co

11、mbination factor for global and local action effects for bridges except road bridges should be 1,0.The combination factor for global and local action effects for road bridges is stated to be a nationally determined parameter in BS EN 1993-2:2006, E.2. The value for this parameter should be as recomm

12、ended in the National Annex to BS EN 1993-2:20061). NA.2.6 Choice of the methods for calculating elastic resistance to bending BS EN 1994-2:2005, 6.2.1.5 (9)In calculating the elastic resistance to bending, the method given in BS EN 1994-2:2005, 6.2.1.5 (7) and (8) or the method given in BS EN 1993-

13、1-5:2006, Section 10 may be used.NA.2.7 Values of CRd,cand k1for concrete flanges in tension BS EN 1994-2:2005, 6.2.2.5 (3)The value of the coefficient CRd,cshould be 0,15/Cas recommended in BS EN 1994-2.The value of the coefficient k1should be 0,12 as recommended in BS EN 1994-2.NA.2.8 Reference to

14、 rules for transverse filler beams BS EN 1994-2:2005, 6.3.1 (1)Rules for transverse filler beams are given in PD 6696-2.1)In preparation.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 24/03/2008 07:27, Uncontrolled Copy, (c) BSI BSI 2007 3NA to BS EN 1994-2:2005NA.2.9 Shear connection BS EN

15、1994-2:2005, 6.6.1.1 (13)No reference is provided to further guidance on considering the effects of bending moments at the steel-concrete interface, about an axis parallel to the axis of the steel beam, caused by deformations of the slab or the steel member, adjacent to cross frames and vertical web

16、 stiffeners, and for composite box girders.NA.2.10 Partial factor for design shear resistance of a headed stud, VBS EN 1994-2:2005, 6.6.3.1 (1)The partial factor for design shear resistance of a headed stud, V, should be 1,25 as recommended in BS EN 1994-2.NA.2.11 Reduction factor for the shear resi

17、stance of a stud connector, ks BS EN 1994-2:2005, 6.8.1 (3)The reduction factor for the shear resistance of a stud connector, ks, should be 0,75 as recommended in BS EN 1994-2. NA.2.12 Partial factor for fatigue strength of studs in shear, Mf,s BS EN 1994-2:2005, 6.8.2 (1)The partial factor for fati

18、gue strength of studs in shear, Mf,s, should be 1,0 as recommended in BS EN 1994-2:2005, 2.4.1.2 (6)P.NA.2.13 Design value of crack width, wk, and the combination of actions BS EN 1994-2:2005, 7.4.1 (4)The value of wk, which should be taken as wmax, and the combination of actions, are stated to be n

19、ationally determined parameters in BS EN 1992-2:2005, 7.3.1 (105). These parameters should be as recommended in the National Annex to BS EN 1992-2:2005.NA.2.14 Specific measures to limit the heat of hydration of cement and the temperature difference to be considered BS EN 1994-2:2005, 7.4.1 (6)Speci

20、fic measures to limit the heat of hydration of cement may be described in a project specification together with the temperature difference to be considered. If no specific measures to limit the heat of hydration of cement are described in the project specification then the temperature difference to

21、be considered should be 25 K.NA.2.15 Shear connection and transverse reinforcement BS EN 1994-2:2005, 8.4.3 (3)No reference is provided to information describing the provision of reinforcement near shear connectors arranged in groups to prevent premature local failure in either the precast or the in

22、 situ concrete.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 24/03/2008 07:27, Uncontrolled Copy, (c) BSINA to BS EN 1994-2:20054 BSI 2007NA.3 Decision on the status of informative annexes BS EN 1994-2:2005, Annex C, Headed studs that cause splitting forces in the direction of the slab thic

23、knessBS EN 1994-2:2005, Annex C should be used.NA.4 References to non-contradictory complementary information Non-contradictory complementary information for use with BS EN 1994-2 is given in PD 6696-2.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 24/03/2008 07:27, Uncontrolled Copy, (c) BS

24、I BSI 2007 5NA to BS EN 1994-2:2005BibliographyStandards publicationsFor dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.BS EN 1992-2:2005, Eurocode 2 Design of concrete structures Part 2: Conc

25、rete bridges Design and detailing rulesBS EN 1993-1-5:2006, Eurocode 3 Design of steel structures Part 1-5: Plated structural elementsBS EN 1993-2:2006, Eurocode 3 Design of steel structures Part 2: Steel bridgesBS EN 1994-1-1:2004, Eurocode 4 Design of composite steel and concrete structures Genera

26、l rules and rules for buildingsNational Annex to BS EN 1992-2:2005: UK National Annex to Eurocode 2 Design of concrete structures Part 2: Concrete bridges Design and detailing rules National Annex to BS EN 1993-2:20062). UK National Annex to Eurocode 3 Design of steel structures Part 2: Steel bridge

27、sPD 6696-2:2007, Background paper to BS EN 1994-2 and the UK National Annex to BS EN 1994-22)In preparation.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 24/03/2008 07:27, Uncontrolled Copy, (c) BSIBSI British Standards InstitutionBSI is the independent national body responsible for prepari

28、ng British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It

29、 is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside fro

30、nt cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should

31、 be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been

32、published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also availabl

33、e which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards.

34、For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available

35、 on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, sto

36、red in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or gra

37、de designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager.Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.Email: copyrightbsi-.NA to BS EN 1994-2:2005389 Chiswick High RoadLondonW4 4ALLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 24/03/2008 07:27, Uncontrolled Copy, (c) BSI