NAVISTAR MPAPS F-6028-2017 Hose Fuel and Oil Resistant Filler Neck.pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. SEPTEMBER 2017 Page 1 of 3 NAVISTAR, INC. Material, Parts, and Process Specificati

2、ons (MPAPS) NUMBER: MPAPS F-6028 Former Designation: TMS-6028 TITLE: Hose, Fuel and Oil Resistant, Filler Neck CURRENT REV No.: 1709 DATE: Sep. 2017 WRITTEN/EDITED BY: G. Svidron APPROVED BY: R. Goluch SUPERSEDES: Rev. 0904 April 2009 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVI

3、SION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regula

4、tory limits prior to use. 1.0 APPLICATION This specification covers a fuel resistant hose suitable for Diesel fuel filler neck connections or other similar applications. 2.0 SCOPE This specification covers the general requirements, property and performance requirements, and source approval and quali

5、ty control requirements. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referen

6、ced standards shall apply. The following standards, specifications and regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 MPAPS F-2 MPAPS P-9543 CFR Title 29, Part 1910 SAE J30 NAVISTAR Supplier Packing and Shipping Std. D-13 MPAPS B-50 4.0 GENERAL REQUIRE

7、MENTS 4.1 Hose Construction The hose shall consist of a smooth bore tube of nitrile rubber, reinforced with one or more plies of textile fiber yarn, cord, or fabric, and finished with a cover of an oil and weather-resistant elastomer. 4.2 Dimensions and Tolerances Hose shall meet the dimensions and

8、tolerance requirements of SAE-30R6. 4.3 Property and Performance Requirements Hose supplied to this specification shall meet all property and performance requirements of SAE30R6 Hose as per SAE J30. 5.0 QUALITY Parts and assemblies will meet the cleanliness requirements of MPAPS F-2 Level III. All h

9、ose produced to this specification will be clean, free of dirt, grease, and contamination. All rubber debris from cutting and processing will be removed. Any internal release agents shall be flushed from the NUMBER: MPAPS F-6028 TITLE: Hose, Fuel And Oil Resistant, Filler Neck REVISION: 1709 This do

10、cument is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. SEPTEMBER 2017 Page 2 of 3 inside of the hose. There shall be no fabric or flash exposed

11、on the ID of the hose. Parts shall be free of voids and/or reinforcement splices. 5.1 Qualification Material and processes submitted for approval to this specification shall include the following: 5.1.1 Report: A detailed and signed test report documenting testing to this specification prepared as p

12、er MPAPS P-9543. The report will include actual test data not merely test summaries. 5.1.2 Failure Modes: Test samples or photographs showing failure modes for each destructive test as necessary to fully describe those failure modes. Descriptions are adequate if the mode is easily understandable (no

13、 jargon) and not unexpected. Unexpected failure modes shall be described or pictured as completely as possible. 5.1.3 Test Procedure: The procedure used for preparing, curing and assembling materials for test. 5.1.4 Analysis: A detailed analysis of the test results including assumptions made, unexpe

14、cted results and an explanation of any non-compliant results. 5.2 Submission The material test report shall be submitted to: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requ

15、irements All suppliers to Navistar Inc. are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers

16、must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those

17、samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Truck Devel

18、opment and Technology Center and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 sha

19、ll be submitted with the request for change. 6.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control a

20、nd with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using Navistar plant may determine testing and reporting requirements on specific products. NUMBER: MPAPS F-6028 TITLE: Hose, Fuel And Oil Resistant,

21、 Filler Neck REVISION: 1709 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. SEPTEMBER 2017 Page 3 of 3 7.0 SHIPPING, PACKING AND I

22、DENTIFICATION Each hose manufacturer shall incorporate into the construction of the hose an identifying yarn (color) as assigned by the Rubber Manufacturers Association. Each hose shall be labeled or marked on the outer cover along the entire length of the hose at intervals of not less than 380 mm (

23、15 inches) in a color contrasting to that of the hose color, in clearly legible block capital letters not less than 3 mm (1/8 inch) high, with the following minimum information in the order listed: (a) Vendor Code - A four-or-five-digit code assigned by Navistar to each vendor. Contact Corporate Tec

24、hnical Standards, Truck Development and Technology Center, for assignment of codes. (b) Hose Type - Identification by hose type, as required. (c) Size - Nominal size, i.e., diameter in fractions of an inch or “dash“ sizes, as required. (d) Date Code - The six-digit date code, with first two digits (

25、01-12) representing the month, (01-31) representing the day, and last two digits (86) representing the year, is the preferred method for date codes. Other methods of date code may be used by agreement between the purchaser and supplier. NOTE: In many cases, DOT, FMVSS, and/or SAE documents and speci

26、fications prescribe a specific marking identification procedure. Where identification requirements of this specification conflict with DOT, FMVSS, and/or SAE requirements, the DOT, FMVSS, and/or SAE requirements shall prevail. 8.0 DESIGNATION ON DRAWINGS Hose per MPAPS F-6028 9.0 TECHNICAL INFORMATI

27、ON For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Markit Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ REVISION HISTORY Revision Level Change Approved by Date Approved 1709 Converted to MPAPS; Updated cleanliness requirement. R. Goluch 9/27/2017