NAVISTAR MPAPS S-B-40 101-GS PL-2015 Round U-Bolts C English Series (Noun Code 0810).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 3 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-B-40.101-GS/PL Former Designation: ESP-B-40.101-GS TITLE: Round U-Bolts English Series (Noun Code 0810) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-B-40.101-GS - August 2006 PRINTED COPIES OF

3、 THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practi

4、ces and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, PP. 1.0 GENERAL: The Round U-Bolts covered by this standard are those used in general purpose applications. 2.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts

5、 are so designated to reduce variety of parts and assure maximum availability interchangeability, and cost savings in volume buying. For new design, parts shall be selected from “Approved“ part list only. Diameters: 1/4, 5/16, 3/8, 1/2, 5/8, 3/4, and 1 inch. Threads: UNC When Shank Length C is: Thru

6、 1/2” dia Over 1/2” dia Length Increments are: Up to 4 inches .25 Inch - From 4 to 12 inches .50 Inch 1.00 inch Over 12 inches 1.00 inch 1.00 inch When Shank Length C is: Thread Length is: Up To and Including 2 inches .75 inch Over 2 inches and Including 3 inches 1.00 inch Over 3 inches and Includin

7、g 6 inches 1.50 inch Over 6 Inches 3.00 inch 3.0 THREADS: Unified coarse, rolled threads. Re-rolled threads are not permissible. Threads will be free from nicks, burrs, slivers, and laps which will affect the nut engagement or torque. 4.0 BODY DIAMETER: The diameter of the unthreaded shank at any po

8、int will not be less than the minimum pitch diameter of the thread. 5.0 FLATNESS: U-bolts are to be flat to within .005 inch per inch of shank length (C). 6.0 MATERIAL: SAE Grade 4 (same as studs) medium carbon cold drawn steel per SAE J429, or Type 5 per NAVISTAR MPAPS F-31, Part I. 7.0 MECHANICAL

9、REQUIREMENTS AND TEST PROCEDURES: The test specimen will be cut stud-like from either shank of the “U“ (utilizing the maximum available thread length). The specimen will meet the mechanical properties and testing requirements as specified for SAE Grade 4 in SAE J429 and for Type 5 as specified in NA

10、VISTAR, INC. MPAPS F-31, Part I. Thread Length: Shank Length Incrementation: NUMBER: MPAPS S-B-40.101-GS/PL TITLE: Round U-Bolts REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are re

11、quired to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 3 8.0 DESIGN GUIDE: It should be recognized that the “U“ configuration may not sustain a load equivalent to two bolts or studs of the same size and material grade or type; thus, actual load carrying capacity of U-bolts

12、 should be determined by saddle load tests. 9.0 FINISH: U-bolts will be furnished coated in accordance with NAVISTAR, INC. Engineering Material Specifications and class listed below: Phosphate Coating (PHC) MPAPS G-1, Class B-2. NOTE: Coating will be applied to the threaded surface and a distance of

13、 1.0 inch minimum above the threads. Complete coating is permissible. 10.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 11.0 WORKMANSHIP: U-bolts will be cl

14、ean and free from rust, scale, sharp edges, folds, laps, pipe, splits, internal bursts, or nonmetallic inclusions which will affect the performance of the bolt. Depth of seams will not exceed 3 percent of the nominal diameter of the U-bolt. TOLERANCES Center to Center dimension (B). + .06 - .00 Shan

15、k Length (C) .06 Thread Length (D) .06 Radii (E) + .03 - .00 Dimensions in inches: Nominal Size 1/4 5/16 3/8 7/16* 1/2 9/16* 5/8 3/4 7/8 1 Threads Per Inch 20 18 16 14 13 12 11 10 9 8 Pitch Dia, Max .2164 .2752 .3331 .3897 .4485 .5068 .5644 .6832 .8009 .9168 Pitch Dia, Min .2127 .2712 .3287 .3850 .4

16、435 .5016 .5589 .6773 .7946 .9100 Pitch Dia, Basic .2175 .2764 .3344 .3911 .4500 .5084 .5660 .6850 .8028 .9188 * Non-Preferred Diameters * Radius is equal to “B” min pitch diameter 2 (Round off min pitch diameter to two places per EDS A-5.) 12.0 PART LIST: 12.1 Approved: Nominal Size A B C D E Part

17、Number Span Width Center DIM Shank Length THD RAD 3/8 -16 1.00 1.38 1.75 .75 .52 726510R1 3/8 -16 4.06 4.44 5.50 1.50 2.06 26943R1 NUMBER: MPAPS S-B-40.101-GS/PL TITLE: Round U-Bolts REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permissio

18、n from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 3 13.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/