NAVISTAR MPAPS S-C-28 101-GS PL-2015 Hexagon Socket Head Cap Screws C English Series (Noun Code 7450).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 13 1.0 GENERAL: This standard conforms essentially with the Am

2、erican National Standard B18.3 for Hexagon Socket Head Cap screws (1960 Series). All but nominal dimensions are shown in decimal inch. 2.0 CONTENTS: Page General 1 Heads 2 Socket 2 Under head Fillet 2 Position of Head Body and Thread 2 Body 2 Length 3 Threads 3 Length of Thread 3 Points 4 Surface Ro

3、ughness 4 Material 5 Finishes 5 Restricted Chemical Substances 5 Workmanship Policy for Selecting Parts for New Design Gages and Gaging 5 5 8 Hexagon Socket Head Capscrews 10 Part List 12 Technical Information 13 NAVISTAR, INC. Material, Parts, and Process Specifications (MPAPS) NUMBER: MPAPS S-C-28

4、.101-GS/PL Former Designation: ESP-C-28.101-GS TITLE: Hexagon Socket Head Cap Screws English Series (Noun Code 7450) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-C-28.101-GS - August 2006 PRINTED COPIES OF THIS DOCU

5、MENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to

6、 determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, PP, NPP. NUMBER: MPAPS S-C-28.101-GS/PL TITLE: Hexagon Socket Head Cap screws REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced w

7、ithout permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 13 3.0 HEADS: The top of screw heads will be flat, perpendicular to the axis of the screw and chamfered at the periphery. The edge between the flat

8、and chamfer may be slightly rounded. The plane of the bearing surface will be perpendicular to the axis of the screw within 1 degree. The edge between the bearing surface and the side of the head may be chamfered or rounded providing the degree of chamfer or rounding measured along the bearing face

9、is within the tabulated limits for “S.“ The head will be at true position with respect to the axis of screw within a tolerance zone having a diameter equal to one percent of the basic screw diameter (J max) two percent total runout or .006 inch, whichever is greater, regardless of feature size. Unle

10、ss otherwise specified, knurling on heads will be optional with the manufacturer providing the diameter across the tops of the knurl and the diameter of the head before knurling or of the unknurled portion are within the tabulated maximum and minimum head diameter limits, respectively. The minimum h

11、ead diameter will be measured on the side of the head adjacent to the chamfer or rounding at periphery of bearing face. 4.0 SOCKET: Where hexagon sockets are chamfered or relieved, the depth of chamfer or relief will not exceed the equivalent of 10 percent of the nominal socket size for sizes up to

12、and including 1/16 inch and 7.5 percent for larger socket sizes. For broached sockets which are at or near the maximum limit of size, the overcut resulting from predrilling will not exceed 20 percent of the length of any flat of the socket on sizes up to and including 1 inch, and 30 percent of the l

13、ength of any flat on larger sockets. Suitability of sockets up to and including 1 inch nominal size will be checked in accordance with the functional limits for runout of head, body, and thread paragraph and the chart specified in the Gages and Gaging portion of this document. Socket will be at true

14、 position with respect to the axis of screw within a tolerance zone having a diameter equal to three percent of the basic screw diameter or .005 inch, whichever is greater, for screws up to and including 1/2 inch; and of a diameter equal to 6 percent of the basic screw diameter for larger screw size

15、s; regardless of feature size. 5.0 UNDERHEAD FILLET: For all lengths of screws, the form of the fillet at junction of head and shank will be optional, providing it fairs into the bearing surface of head within the limits established by “E“ maximum plus “Q“ maximum and “E“ minimum plus “Q“ minimum, a

16、nd is a smooth and continuous curve having a bearing surface juncture radius of not less than “R.“ 6.0 POSITION OF HEAD. BODY AND THREAD: Positional relationship of head, body and threads on screws will be such that screws will meet functional limits specified within the “Functional Limits for Runou

17、t of Head, Body, and Thread” paragraph. 7.0 BODY: The diameter of body on screws for which the body length “LB“ is applicable will be within the limits tabulated. For screws threaded full length, the diameter of the unthreaded shank under the head will not exceed the specified maximum body diameter

18、nor be less than the minimum pitch diameter of the thread. NUMBER: MPAPS S-C-28.101-GS/PL TITLE: Hexagon Socket Head Cap screws REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are req

19、uired to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 13 8.0 LENGTH: The length of capscrews will be measured, parallel with the axis of screw, from the plane of the bearing surface of the head to the plane of the flat of the point. The tolerance on screw length will be as

20、 tabulated below: Nominal Size 0 thru 3/8 7/16 thru 3/4 7/8 thru 1-1/2 Over 1-1/2 Nominal Length Tolerance on Length Up to 1 inch, Incl -.03 -.03 -.05 - Over 1 inch to 2-1/2, Incl -.04 -.06 -.10 -.18 Over 2-1/2 to 6, Incl -.06 -.08 -.14 -.20 Over 6 -.12 -.12 -.20 -.24 9.0 THREADS: Unified external t

21、hreads with radius root: Class 3A, UNRC and UNRF Series for screw sizes 1 inch and smaller; and Class 2A, UNRC and UNRF Series for sizes over 1 inch, to and including 1 1/2 inches. Acceptance gaging of Class 3A threads will be on the basis of thread ring gages. 10.0 LENGTH OF THREAD: On socket head

22、capscrews, the length of thread, except on short length screws, will be controlled by the grip gaging length “LG“ and the body length “LB.“ The applicable “LG“ and “LB“ dimensions for standard nominal lengths in screw sizes up to and including 1 inch are specified in Table 1. For screw sizes and len

23、gths not covered in Table 1, the control on length of thread will be as described below. Grip gaging length “LG“ is maximum and will be measured, parallel to the axis of screw, from the bearing surface of the head to the face of a noncounterbored or noncountersunk standard GO thread ring gage assemb

24、led by hand as far as thread will permit. It represents the minimum design grip length of the screw and will be used as the criterion for inspection and for determining thread availability when selecting screw lengths even though usable threads may extend beyond this point, on some products. Body le

25、ngth “LB“ is a minimum and will be measured, parallel to the axis of screw, from the bearing surface of the head to the last scratch of thread or the top of the extrusion angle. It also will be used as a criterion for inspection. The tabulated values are equal to “LG“ minus 5 times the pitch of the

26、UNRC thread for the respective screw size. For screws having nominal lengths which fall between the lengths shown in Table 1, the “LG“ and “LB“ dimensions will conform with those specified for the next shorter length for the respective screw size. For example: On a 1/4 inch size screw of 1-7/8 nomin

27、al length, “LG“ would be .50 inch and “LB“ would be .25 inch. Screws having nominal lengths which fall above heavy horizontal line in Table 1 and, in sizes 1 inch and larger, lengths which are shorter than “LT“ plus 5 times the pitch of the UNRC thread; will be threaded for full length. On these scr

28、ews the complete (full form) threads, as measured with a noncountersunk or noncounterbored standard GO ring gage, will extend to within two pitches (threads) of the bearing surface of the head for sizes up to and including 5/8 inch (see “U“ in tabulation below), and as close to the bearing face as i

29、s practicable for all larger sizes. NUMBER: MPAPS S-C-28.101-GS/PL TITLE: Hexagon Socket Head Cap screws REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all pat

30、ent liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 13 For screws having longer nominal lengths than those shown in Table 1 and for screw sizes over 1 inch, the maximum grip gaging length “LG“ and minimum body length “LB“ will be determined as follows: LG= L - LT LB= L - LTT Dimensions in inch

31、es: Nominal Size LT LTT U Nominal Size LT LTT U Thread Length Total Thread Length Unthreaded Length Thread Length Total Thread Length Unthreaded Length Max Max Min Max Coarse Thread Fine Thread Min Max Coarse Thread Fine Thread 0 .50 .62 .025 3/8 1.25 1.94 .125 .083 1 .62 .77 .031 .028 7/16 1.38 2.1

32、7 .143 .100 2 .62 .80 .036 .031 1/2 1.50 2.38 .154 .100 3 .62 .83 .042 .036 5/8 1.75 2.82 .182 .111 4 .75 .99 .050 .042 3/4 2.00 3.25 - - 5 .75 1.00 .050 .045 7/8 2.25 3.69 - - 6 .75 1.05 .062 .050 1 2.50 4.12 - - 8 .88 1.19 .062 .056 1-1/8 2.81 4.65 - - 10 .88 1.27 .083 .062 1-1/4 3.12 5.09 - - 1/4

33、 1.00 1.50 .100 .071 1-3/8 3.44 5.65 - - 5/16 1.12 1.71 .111 .083 1-1/2 3.75 6.08 - - The minimum thread length “LT“ and maximum total thread length “LTT“ are reference dimensions included herein for calculation purposes only. The minimum thread length “LT“ represents the distance, measured parallel

34、 to the axis of screw, from the extreme point to the last complete (full form) thread. The maximum total thread length “LT-r“ represents the distance, parallel to the axis of screw, from the extreme point to the last scratch of thread or the top of the extrusion angle. The tabulated “LTT“ values inc

35、lude the minimum thread length plus a factor of 5 times the UNRC pitch, to provide for incomplete threads and a tolerance on grip length, plus an allowance which will permit the use of common tooling for more than one screw length. 11.0 POINTS: The end of screw will be flat or slightly concave and c

36、hamfered. The plane of the point will be approximately normal to the axis of the screw. The chamfer will extend slightly below the root of the thread and the edge formed by the flat and chamfer may be slightly rounded. The included angle of the point should be approximately 90 and will produce a len

37、gth of chamfered or partial thread equivalent to .75 to 1.25 times the pitch of the thread. Chamfering of points on screw sizes up to and including size 8 (.164) will be optional. 12.0 SURFACE ROUGHNESS: For alloy steel, screws of sizes up to and including 5/8 inch and nominal lengths equal to or le

38、ss than 8 times the basic screw diameter, the surface roughness before plating will not exceed 63 microinches (arithmetical average) on the fillet and head bearing surfaces, nor exceed 32 microinches (arithmetical average) on the threads. For larger sizes, longer lengths and corrosion resistant stee

39、l screws, the surface roughness prior to plating will not exceed 125 microinches (arithmetical average) on the body, fillet and head bearing surfaces. NUMBER: MPAPS S-C-28.101-GS/PL TITLE: Hexagon Socket Head Cap screws REVISION: 1506 This document is restricted and may not be sent outside Navistar,

40、 Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 5 of 13 Normally, it will be sufficient to ascertain that these surfaces on screws have the equivalent of a smooth machined finish b

41、y visual comparison with known surface standards. However, where it is deemed necessary and proves practical to measure these surfaces with commercially available equipment, roughness measurements will be taken axially on the body and fillet surfaces, and circumferentially on the bearing face. (See

42、EDS A-12, Surface Texture.) 13.0 MATERIAL: As designated by part number, socket head cap screws will be made from steel or corrosion resistant steel conforming to the specifications below: Steel screws will be fabricated from an alloy steel having one or more of the following alloying elements; chro

43、mium, nickel, molydenum, or vanadium, in sufficient quantity to assure that the hardness range at the surface of Rockwell C39 to 45 for screw sizes up to and including 10 (.190) and Rockwell C37 to 45 for larger screw sizes, is met when the screws are hardened by quenching from the austenitizing tem

44、perature and tempered at a temperature of not less than 343 C (650 F). Screws will have properties conforming to ASTM Standard A574. Corrosion resistant steel screws will be fabricated from austenitic corrosion resistant steel of types 18-8, AISI 384, or equivalent types, and will have a minimum ten

45、sile strength of 80,000 psi for sizes up to and including 5/8 inch and 70,000 psi for larger sizes. 14.0 FINISHES: As designated by part number, screws will be furnished plain, plated or coated in accordance with the International Engineering Material Specification and class listed below: Zinc with

46、Chromate (ZN6A) on steel MPAPS G-20, Class 6A. Phosphate Coating (PHC) MPAPS G-1, Class B2. Black Oxide (BLO) - Standard with manufacturer. 15.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements

47、 of the MPAPS B-50 specification. 16.0 WORKMANSHIP: Screws will be free from all defects which might affect their serviceability. 17.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability and cost s

48、avings in volume buying. For new design, parts shall be selected from “Approved“ part list only. Material: Alloy Steel Finish: Plain (PLN), Zinc with Chromate (ZND), and Phosphate Coating (PHC) Thread: Coarse Diameters: 6, 8, 10, 1/4, 5/16, 3/8, 1/2, 5/8, 3/4, 1, 1-1/4 and 1-1/2 NUMBER: MPAPS S-C-28

49、.101-GS/PL TITLE: Hexagon Socket Head Cap screws REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 6 of 13 Lengths: All Diameters - 1/4 inch Increments thru 4 inches All preferred lengths beyond the ranges indicated above will be carried in the non-preferred section because of limited usage. TABLE 1 - GRIP GAGING LENGTHS AND BODY LENGTHS Dimensions in inches: Nom Size 0 1 2 3 4