NAVISTAR MPAPS S-J-1 101-GS PL-2015 Split (Cotter) Pins C Extended Prong C English Series (Noun Code 6200).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 6 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-J-1.101-GS/PL Former Designation: ESP-J-1.101-GS TITLE: Split (Cotter) Pins Extended Prong English Series (Noun Code 6200) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-J-1.101-GS - August 2006

3、 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety

4、 and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, PP, NPP. 1.0 GENERAL: This specification conforms in all essentials with ANSI B18.8.1. The inclusion of dimensional data is not intended to imply that

5、all pins described are stock production sizes. Metric series split (cotter) pins may be found on page MPAPS S-JM-1.101-GS/PL. 2.0 CONTENTS: 3.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability a

6、nd cost savings in volume buying. For new design, parts shall be selected from “Approved“ part list only. Page General 1 Policy for Selecting Parts for New Design 1 Service Parts Substitution Policy 2 Head 2 Points 2 Length 3 Tolerance on Length 3 Wire Section 3 Material 3 Ductility 3 Finishes 3 Res

7、tricted Chemical Substances 3 Workmanship 3 Dimensions 4 Part List 5 Conversion List 5 Technical Information 6 NUMBER: MPAPS S-J-1.101-GS/PL TITLE: Split (Cotter) Pins-Extended Prong REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permissio

8、n from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 6 Nominal Sizes: 1/32, 1/16, 3/32, 1/8, 5/32, 3/16, and 1/4 Lengths: See Chart Below (Based on sizes and length normally available.) Material: Steel (STL) Point: Ex

9、tended Prong Finish: Plain (PLN) Dimensions in inches: Nominal Pin Length Nominal Pin Size 1/32 1/16 3/32 1/8 5/32 3/16 1/4 1/4 x 3/8 x x 1/2 x x x x 3/4 x x x x x x 1 x x x x x x x 1 - 1/4 x x x x x x 1 - 1/2 x x x x x x 1 - 3/4 x x x x x x 2 x x x x x x 2 - 1/4 x x x x x 2 - 1/2 x x x x x 2 - 3/4

10、x x x x 3 x x x x 3 - 1/2 x x 4 x x The sizes marked x are normally carried in stock. 4.0 SERVICE PARTS SUBSTITUTION POLICY: In the event that engineering does not indicate a “Do not substitute“ in engineering specifications, the following substitutions may be implemented in service. This policy is

11、the result of a proposal circulated April 20, 1981, and subsequently approved by engineering departments worldwide. Split (Cotter) Pins - Extended Prong To be Replaced Service Replacement Plain finish (PLN) Because of the superior shelf life, zinc trivalent finish (ZN6A) is recommended for service.

12、Phosphate Coating Finish (PHC) Zinc trivalent finish (ZN6A) All lengths below one inch with 1/16th inch increments, sub the next longer 1/8th inch increment. Example: 3/8th inch for 5/16 inch. All lengths above 1 inch with 1/8th inch increments sub the next longer 1/4 inch increment. Example: 1-1/4

13、inch for 1-1/8 inch. 5.0 HEAD: The contour of the head will be optional with the manufacturer provided the specified dimensions are maintained and there is no sharp indentation at the juncture of head and shank. 6.0 POINTS: The ends of points will not be open and any gaps occurring between the prong

14、s along the shank portion of pins beyond the point will not exceed .015 inch. The lateral misalignment of prongs over the entire length of shank will not exceed .015 inch. NUMBER: MPAPS S-J-1.101-GS/PL TITLE: Split (Cotter) Pins-Extended Prong REVISION: 1506 This document is restricted and may not b

15、e sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 6 7.0 LENGTH: The length (L) will be measured parallel to the axis of the pin, from the plane of contac

16、t of a ring gage with the head of pin to the end of the shortest prong. The ring gage will have a hole or diameter equal to the nominal pin size within a tolerance of .001 inch. The permissible break or rounding at the gaging edges of hole will not exceed .005 inch. Length measurement will be taken

17、with pin inserted into gage under finger force not to exceed 8 oz. 8.0 TOLERANCE ON LENGTH: The tolerance on length will be as tabulated below: Nominal Pin Length Tolerance Length Up to 1 inch .03 inch 1 inch and longer .06 inch 9.0 WIRE SECTION: The material will be rolled or drawn from wire having

18、 a half round section, the flat side of which preferably will have a small degree of rounding (a radius equal to 7.5 to 10 percent of the minimum pin diameter) at the edges rather than sharp corners. 10.0 MATERIAL: Stainless Steel (SST) - Type 18-8 per MPAPS A-37. Type 18-8 are nonmagnetic general p

19、urpose stainless with excellent corrosion resistance and will be *passivated per MPAPS A-37. Steel (STL) MPAPS A-0, Part II, Code 0-100 Brass (BRS) CEMS C-3, Grade C26000 11.0 DUCTILITY: Each prong of the cotter pin will be capable of withstanding being bent back upon itself (180 degrees) once with

20、no visible indication of fracture occurring at the point of bend. 12.0 FINISHES: In accordance with MPAPS and class below: Plain (PLN). Zinc Trivalent (ZN6A) MPAPS G-20, Class 6A. Phosphate Coating (PHC) MPAPS G-1, Class B-2 Chromium Bright (CRB) MPAPS G-19, Class 13 CRB 13.0 RESTRICTED CHEMICAL SUB

21、STANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 14.0 WORKMANSHIP: Pins will not contain imperfections which affect usability or serviceability such as excessive amounts of burrs, loo

22、se scale or irregular surfaces. NUMBER: MPAPS S-J-1.101-GS/PL TITLE: Split (Cotter) Pins-Extended Prong REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all pate

23、nt liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 6 15.0 DIMENSIONS: Dimensions in inches: Nominal Size Shank Head Outside Prong Hole Diameter Diameter Extension Diameter Max Min Min Min Nom 1/32 .032 .028 .062 .01 .047 3/64 .048 .044 .094 .02 .062 1/16 .060 .056 .125 .03 .078 * 5/64 .076 .07

24、2 .156 .04 .094 3/32 .090 .086 .188 .04 .109 * 7/64 .104 .100 .219 .05 .125 1/8 .120 .116 .250 .06 .141 * 9/64 .134 .130 .281 .06 .156 5/32 .150 .146 .312 .07 .172 3/16 .176 .172 .375 .09 .203 * 7/32 .207 .202 .438 .12 .234 1/4 .225 .220 .500 .12 .266 * 5/16 .280 .275 .625 .12 .312 * 3/8 .335 .325 .

25、750 .12 .375 * 7/16 .406 .400 .875 .19 .438 * 1/2 .473 .467 1.000 .19 .500 * 5/8 .598 .590 1.250 .19 .625 * 3/4 .723 .715 1.500 .19 .750 * Non-Preferred Sizes NUMBER: MPAPS S-J-1.101-GS/PL TITLE: Split (Cotter) Pins-Extended Prong REVISION: 1506 This document is restricted and may not be sent outsid

26、e Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 5 of 6 16.0 PART LIST: 16.1 Approved: Nominal Size Length Finish Material Part Number Nominal Size Length Finish Material

27、 Part Number 1/16 1/2 PLN STL 103361 5/32 1 1/2 PLN STL 103398 1/16 1 PLN STL 103363 5/32 2 PLN STL 103400 1/16 1 1/4 PLN STL 103364 3/16 1 PLN STL 103407 3/32 3/4 PLN STL 103373 3116 1 1/2 PLN STL 103409 3/32 1 PLN STL 103374 3/16 2 PLN STL 103411 3/32 1 1/4 PLN STL 103375 3/16 2 1/2 PLN STL 103413

28、 1/8 3/4 PLN STL 103384 1/4 1 1/4 PLN STL 103419 1/8 1 PLN STL 103385 1/8 1 1/8 PLN STL 108635 1/8 1 1/2 PLN STL 103387 1/8 1 1/4 ZN6A STL 120123 1/8 1 3/4 PLN STL 103388 1/8 1/8 PHC STL 137195 5/32 3/4 PLN STL 103395 1/8 1/8 ZN6A STL 137204 5/32 1 PLN STL 103396 1/8 1/8 ZN6A STL 137214 3/32 5/8 ZN6

29、A STL 137159 1/8 1/8 ZN6A STL 17233R1 3/32 3/4 PLN SST 220257 5/32 5/32 PLN BRS 12455R1 3/32 3/4 ZN6A STL 121222 7/64 7/64 PLN STL 121673 3/32 1 ZN6A STL 121224 5/32 5/32 PLN BRS 12455R1 3/32 1 1/4 ZN6A STL 119120 3/16 3/16 ZN6A STL 18481R1 3/32 1 1/2 PLN SST 40335R1 3/16 3/16 ZN6A STL 20328R1 3/32

30、2 PLN SST 40306R1 3/16 3/16 ZN6A STL 137258 1/8 3/4 PLN SST 187352 3/16 3/16 ZN6A STL 23368R1 1/8 3/4 ZN6A STL 177923 1/4 1/4 ZN6A STL 20341R1 1/8 7/8 PLN STL 108630 1/4 1/4 PLN STL 13220R1 1/8 1 ZN6A STL 137185 16.2 Not for New Design: Nominal Size Length Finish Material Part Number 3/16 2 1/4 PLN

31、STL 103412 17.0 CONVERSION LIST: 17.1 Approved: Nominal Size Length Finish Material Part Number Replacement Number 1/8 3/4 PLN STL 13042R1 103384 1/8 3/4 ZN6A STL 21628R1 177923 1/8 1 PLN STL 13066R1 103385 1/8 1 ZN6A STL 21630R1 137185 1/8 1 1/8 ZN6A STL 21979R1 137190 1/8 1 1/2 ZN6A STL 21821R1 13

32、7204 1/8 1 3/4 ZN6A STL 22915R1 137214 5/32 2 PLN STL 13155R1 103400 3/16 1 PLN STL 13068R1 103407 3/16 1 ZN6A STL 21632R1 18481R1 3/16 1 1/2 PLN STL 13120R1 103409 3/16 1 3/4 ZN6A STL 21983R1 137258 3/16 2 1/2 PLN STL 13180R1 103413 1/4 1 1/4 PLN STL 13095R1 103419 1/4 2 ZN6A STL 21822R1 20341R1 Se

33、lf opening cotter pins were manufactured by West Pullman Plant and are no longer available. The replacement parts are the equivalent extended prong cotter pins shown in section 16.0 and 17.0. NUMBER: MPAPS S-J-1.101-GS/PL TITLE: Split (Cotter) Pins-Extended Prong REVISION: 1506 This document is rest

34、ricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 6 of 6 18.0 TECHNICAL INFORMATION: For further information related to the technical cont

35、ent of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/