NAVISTAR MPAPS S-J-15 101-GS PL-2015 Cup Plugs C English Series Not Recommended for New Design (Noun Code 6400).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 4 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-J-15.101-GS/PL Former Designation: ESP-J-15.101-GS TITLE: Cup Plugs English Series Not Recommended for New Design (Noun Code 6400) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-J-15.101-GS - Ma

3、rch 2011 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriat

4、e safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, PP, NPP, NR. 1.0 GENERAL: The Cup Plugs listed in section 9.0 are intended for general production applications. Stainless Steel plugs shown in

5、section 9.0 are considered special application parts because of cost and limited availability. Salvage Plugs shown in section 10.0 are for use in salvage operations only and should not be designed into products. 2.0 MATERIAL: Steel, Grade 1, per MPAPS A-6, Part I. Austenitic stainless steel, Types 2

6、00 or 300 series, per MPAPS A-37. 3.0 FINISH: As designated by part number, plugs will be furnished plain, plated or coated in accordance with MPAPS and class listed below. Zinc Trivalent (ZN6A) on steel MPAPS G-20, Class 6A. Note: May be made from galvanized steel, GR 1 GALV, 60G60G U/E or 90G90G U

7、/E, per MPAPS A-6, Part II. 4.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 5.0 ASSEMBLY CONSIDERATIONS: The recommended hole diameter limits specified wil

8、l provide suitable assembly under average conditions. However, deviations from these recommendations may be desirable to provide optimum assembly and performance to suit special conditions. A suitable lubricating oil is recommended wherever possible during installation of plugs to facilitate inserti

9、on and prevent galling. To facilitate assembly and prevent scoring of plugs at insertion, it is recommended that entering edge of hole be relieved with as large a tangential radius as the wall thickness will permit. An alternative, although not preferred, is a countersink of 30 maximum included angl

10、e; to a minimum NUMBER: MPAPS S-J-15.101-GS/PL TITLE: Cup Plugs REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUN

11、E 2015 Page 2 of 4 diameter.012 to.016 inch larger than the plug in its free state. The depth of the relief will be such as to permit open end of plugs to be inserted .010 inch minimum beyond the point of tangency or intersection of countersink on wall of hole. 6.0 INSTALLATION: Plugs should be driv

12、en from the inside bottom and not from the outer edge, or rim of the cup. This can best be accomplished by use of a round arbor .020 to .025 inch smaller in diameter than the inside diameter of plug (A min - 2C max), the driving end is flat and perpendicular to axis of arbor with edge rounded to .06

13、 inch radius. Where plugs are used in counterbored holes, care should be exercised in insertion to prevent the plug from bottoming on the shoulder of counterbore which could result in distortion of plug and loss of seal. 7.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated

14、 to reduce variety of parts and assure maximum availability, interchangeability, and cost savings in volume buying. For new design, parts shall be selected from “Approved“ part list only. Sizes: 3/8 to 1 inch - 1/16 inch increments. Over 1 inch - 1/8 inch increments. Material: Steel Finishes: Plain

15、8.0 WORKMANSHIP: Cup plugs must be free from burrs, loose scale and all other defects that affect their serviceability. 9.0 PART LIST: 9.1 Approved: STANDARD PLUGS - STEEL Nominal Plug Size Outside Diameter * Overall Height Crown Height Stock Thickness Recommended Hole Diameter Part Number Max Min M

16、ax Min Max Min Nominal Tolerance Min Max Plain Finish Zinc Finish * 5/16 .318 .316 .208 .168 .075 .049 .042 .003 .310 .312 28010R1 1/2 .512 .510 .270 .230 .075 .049 .042 .003 .504 .506 21050R1 40064R1 5/8 .637 .635 .270 .230 .075 .049 .042 .003 .629 .631 327411R1 13/16 .825 .823 .270 .230 .083 .057

17、.048 .004 .817 .819 327412R1 7/8 .887 .885 .270 .230 .083 .057 .048 .004 .879 .881 373553R1 1 1.012 1.010 .330 .290 .103 .067 .048 .004 1.002 1.005 318300R1 1-1/4 1.262 1.260 .330 .290 .103 .067 .048 .004 1.252 1.255 349373R1 NUMBER: MPAPS S-J-15.101-GS/PL TITLE: Cup Plugs REVISION: 1506 This docume

18、nt is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 4 STANDARD PLUGS - STEEL Nominal Plug Size Outside Diameter * Overall Hei

19、ght Crown Height Stock Thickness Recommended Hole Diameter Part Number Max Min Max Min Max Min Nominal Tolerance Min Max Plain Finish Zinc Finish 1-3/8 1.388 1.386 .330 .290 .113 .077 .060 .004 1.378 1.381 151162R1 379277C1 1-1/2 1.508 1.506 .330 .290 .113 .077 .060 .004 1.497 1.500 327413R1 1-5/8 1

20、.642 1.640 .380 .340 .113 .077 .060 .004 1.631 1.634 70128R1 * NON-PREFERRED SIZES * Average of maximum and minimum measured diameters of coined surface. Diameter below coined surface may be .0025 inch undersize. Hole diameters shown are for general applications. NOTE: Suggested bore finish should n

21、ot exceed 100 micro inch (AA) for minimum efficiency. For plug sizes designed for salvage applications, see section 9.2. Dimensions in inches: STANDARD PLUGS - STAINLESS STEEL, PLAIN Nominal Plug Size A D F C E Part Number Outside Overall Crown Stock Recommended Diameter * Height Height Thickness Ho

22、le Diameter* Max Min Max Min Max Min .004 Min Max 5/16 .318 .316 .208 .168 .075 .049 .042 .310 .312 28179R1 9/16 .577 .574 .280 .240 .075 .049 .042 .566 .568 40090R1 3/4 .765 .762 .280 .240 .083 .057 .048 .754 .756 25377R1 7/8 .891 .887 .280 .240 .083 .057 .048 .879 .881 27551R1 1-1/8 1.140 1.136 34

23、0 .300 .103 .067 .048 1.127 1.130 21427R1 1-1/4 1.266 1.262 .340 .300 .103 .067 .048 1.252 1.255 23623R1 1-1/2 1.514 1.510 .340 .300 .113 .077 .060 1.497 1.500 601093C1 1-5/8 1.649 1.645 .390 .350 .113 .077 .060 1.631 1.634 22263R1 2 2.019 2.015 .390 .350 .153 .097 .060 2.001 2.004 20840R1 2-1/4 2.2

24、68 2.263 .390 .350 .153 .097 .060 2.251 2.254 24493R1 * Average of maximum and minimum measured diameters of coined surface. Diameter below coined surface may be .0025 inch undersize. *Hole diameters shown are for general applications. NOTE: 1. Suggested bore finish should not exceed 100 microinch (

25、AA) for minimum efficiency. 2. All Stainless Steel Plugs must be stamped with the letter S in the center of the concave portion of each plug. For plug sizes designed for salvage applications, see section 9.2. NUMBER: MPAPS S-J-15.101-GS/PL TITLE: Cup Plugs REVISION: 1506 This document is restricted

26、and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 4 9.2 Not for New Design: Dimensions in inches: SALVAGE PLUGS Nominal Plug Size A D F C E

27、Part Number Outside Diameter* Overall Height Crown Height Stock Thickness Recommended Hole Diameter* Steel Max Min Max Min Max Min .003 Min Max Plain 1 3/16 1.198 1.196 .330 .290 .103 .067 .050 1.188 1.191 337091R1 * Average of maximum and minimum measured diameters of coined surface. Diameter below

28、 Coined surface may be .0025 inch undersize. * Hole diameters shown are for general applications; see General Specifications. NOTE: Suggested bore finish should not exceed 100 micro inches (AA) for minimum efficiency. For production applications, see section 9.0. 10.0 TECHNICAL INFORMATION: For furt

29、her information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/