NAVISTAR MPAPS S-JM-77 101-GS PL-2015 Headed Pins - Metric Series (Noun Code - 6200).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 4 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-JM-77.101-GS/PL Former Designation: ESP-JM-77.101-GS TITLE: Headed Pins - Metric Series (Noun Code - 6200) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-JM-77.101-GS - August 2006 PRINTED COPIE

3、S OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health pr

4、actices and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, GI. 1.0 GENERAL: Implementation of this standard must be in accordance with the policies and procedures outlined in MPAPS S-A-0.101. There may also be supplemental g

5、roup instructions in regard to use of metric standards that should be taken into account. There are no national or international standards on this product. The specifications are based upon West Pullman manufacture and user requirements. Inch dimensioned pins may be found on MPAPS S-J-77.101-GS/PL.

6、2.0 DESIGN CONSIDERATION: Headed pins are an inexpensive and effective approach where loading is primarily in shear. When used in shear, the shear plane of the pin should be kept a minimum distance of one diameter from the end of the pin. In most shear applications, it is desirable that the pin fail

7、s before the shafts or couplings with which they are being used. Headed pins may also be used to position and lock parts in alignment, serve as a hinge or can be used as a locating surface. When drilled, headed pins are locked in place with split (cotter) pins. 3.0 METRIC-INCH RELATED SIZES: During

8、the inch to metric design transition period, the following chart of related sizes can be used for reference. This information is not to be considered as a recommendation for substitutions but only as a means of determining approximate dimensional equivalents. Metric Series Approximate mm Inch Series

9、 6 1/4 8 5/16 10 3/8, 7/16 12 1/2 16 9/16, 5/8 20 3/4 24 1 NUMBER: MPAPS S-JM-77.101-GS/PL TITLE: Headed Pins -Metric Series REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are requir

10、ed to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 4 4.0 COLOR CODING: Not recommended, except in cases where adequate insurance is needed to prevent mixing of “metric parts” with look-alike “inch parts.“ The color blue is standard identifier used in some industries. This

11、must be handled internally at individual plants where needed and is meant to be supplemental to the normal finish and easily deleted when the need for supplemental identification no longer exists. The supplemental blue color should not be used on finishes such as chromium bright which are specified

12、for cosmetic purposes, or phosphate coating which may cause a loss of color identity. 5.0 METHOD OF DESIGNATION: Headed pins will be designated by size, length, word description, material, finish, special feature, if any, and part number as follows: 6 x 20 mm, Headed Pin, Class 8.8, ZN6A, DRLD, Part

13、 Number 6.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability, and cost savings in volume buying. For new design, parts shall be selected from “Approved“ part list only. Class 5.8 Class 8.8 Mater

14、ial: Steel Finish: Plain (PLN) Zinc Trivalent (ZN6A) Zinc Trivalent (ZN6A) Nominal Sizes Dimensions in millimeters: and Length Nominal Nominal Sizes Incrementation: Lengths 6 8 10 12 16 20 24 12 X 16 X X 20 X X X 25 X X X X 30 X X X X 35 X X X X X 40 X X X X X X 45 X X X X X X 50 X X X X X X X 55 X

15、X X X X X X 60 X X X X X X X 65 X X X X X X 70 X X X X X X 80 X X X X X X 90 X X X X X 100 X X X X X 120 X X X X 140 X X X 160 X X 190 X 200 X 20 mm Increments Over 200 NUMBER: MPAPS S-JM-77.101-GS/PL TITLE: Headed Pins -Metric Series REVISION: 1506 This document is restricted and may not be sent ou

16、tside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 4 7.0 HEADING REQUIREMENTS: All pins 16 mm in diameter or less than 150 mm in length will be cold headed. Sizes

17、over 16 mm and lengths more than 150 mm can be either cold or hot headed. 8.0 MATERIAL: Un-heat treated and heat treated steel pins will conform to the chemical composition, hardness and heat treatment requirements for bolts per MPAPS F-31, Part 1, as specified below: Un-heat treated pins - Class 5.

18、8 Heat treated pins - Class 8.8 9.0 FINISHES: Pins will be furnished plain or plated in accordance with the MPAPS and class listed below. Zinc Trivalent, Class 6A (ZN6A) MPAPS G-20, Class 6A. 10.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of

19、this specification must comply with the requirements of the MPAPS B-50 specification. 11.0 WORKMANSHIP: Pins will be free from burrs, loose scale, sharp edges and other defects affecting their serviceability. 12.0 DIMENSIONS: 12.1 Approved: Dimensions in millimeters: Nominal Size or Basic Diameter A

20、 B C D E G H J Recommended Split (Cotter) Pin Shank Diameter Head Height Head Diameter Hole Size End to Radius Radius Point Length Cold Hot Center Headed Formed Ref Max Min Min Max Min Max Min Max Min Min Nom Nom Max Size Part Number 6 6 5.85 5.75 2.25 2 9.5 9 1.85 1.6 3.2 6.8 1.4 1.6 x 12 932951R1

21、1.6 10 10 9.83 9.7 3.75 3.5 15.5 15 3.5 3.2 4.5 11 2.7 3.2 x 20 934792R1 3.2 12 12 11.8 11.64 4.5 4.25 18.5 18 3.5 3.2 5.5 13.5 3 3.2 x 20 934792R1 16 16 15.8 15.64 6 5.75 24.5 24 4.3 4 6 18 3.8 4 x 25 30243R1 NOTE: Min “E“ dimension (distance from center line of hole to end of pin) is specified for

22、 calculating hole location from under side of head. NUMBER: MPAPS S-JM-77.101-GS/PL TITLE: Headed Pins -Metric Series REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to a

23、ssume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 4 13.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/