NAVISTAR MPAPS S-L-61 101-GS PL-2015 Drain and Shut-Off Cocks - English Series (Noun Code 9620).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 4 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-L-61.101-GS/PL Former Designation: ESP-L-61.101-GS TITLE: Drain and Shut-Off Cocks - English Series (Noun Code 9620) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-L-61.101-GS - September 2000 P

3、RINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety a

4、nd health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, PP. 1.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the re

5、quirements of the MPAPS B-50 specification. 2.0 DIMENSIONS AND TOLERANCES: All dimensions will apply to the finished parts, plated, hardened or otherwise processed as specified by the purchaser. Tolerance on all dimensions not otherwise limited will be plus or minus .010 inch. Fitting seats must be

6、concentric with straight thread pitch diameters within .010 inch full indicator reading. Maximum and minimum across flat dimensions will be commercial tolerances of bar or extruded material from which the parts are made. The minimum across corners dimension of hexagons will be 1.092 times the nomina

7、l width across flats. 3.0 STRAIGHT THREADS: Unified and American National Standard; Class 2A external and Class 2B internal threads will apply to plain finish (unplated) fittings. For externally threaded parts with additive finish, the maximum diameters of Class 2A may be exceeded by the amount of t

8、he allowance, i.e., the basic diameters (Class 2A maximum diameter plus the allowance) apply to an externally threaded part after plating. For internally threaded parts with additive finish, the Class 2B diameters apply after plating. For straight thread eccentricity tolerances, see EM-16. External

9、threads will be chamfered to the closest 1/64 inch diameter smaller than the basic minor diameter within a tolerance of minus 1/64 inch on the diameter to produce approximately one incomplete thread and not to exceed one and one-half incomplete threads. Internal threads will be countersunk 90 includ

10、ed angle to the closest 1/64 inch diameter larger than the nominal diameter within a tolerance of plus 1/64 inch on the diameter. 4.0 PIPE THREADS: The pipe threads will conform with the Dry seal American National Standard Taper Pipe Thread or the Dry seal SAE Short Taper Pipe Thread as specified in

11、 the SAE Dry seal Pipe Thread Standard, except as hereinafter noted. Due to design limitations the full thread lengths and shoulder lengths of some externally threaded fittings specified in section 7.0 have been shortened to the minimum required to meet acceptable NUMBER: MPAPS S-L-61.101-GS/PL TITL

12、E: Drain and Shut-Off Cocks REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 4 assembly conditio

13、ns. The external pipe threads are designated as shown in the illustrations on the following pages and the deviations from standard practice are described below. Dryseal Special Short External Taper Pipe Thread is shortened one thread at the small end and also one thread at the large end and is gaged

14、 the same as the Dryseal SAE Short Taper Pipe Thread, using thin ring gage only. Dryseal Special Extra Short External Taper Pipe Thread is shortened one thread at the small end and also two threads at the large end and is gaged 1-3/4 to 3-1/4 turns engagement for the 1/8 size, using special thin rin

15、g gage with one-half pitch (thread) ground off large end and rechamfered. The above deviations are peculiar to these types of fittings, and as special considerations are involved, caution should be exercised in specifying the deviations for any other products. External pipe threads will be chamfered

16、 to the closest 1/64 inch diameter smaller than the minor diameter within a tolerance of minus 1/64 inch on the diameter to produce approximately one incomplete thread and not to exceed one and one-half incomplete thread. Internal pipe threads will be countersunk 90 included angle to the closest 1/6

17、4 inch diameter larger than the major diameter within a tolerance of plus 1/64 inch on the diameter. Specifications for Dryseal pipe threads and related specifications covering blank sizes, blind hole depths, pipe taps, chasers, tap drills, gages, thread length definitions, etc., are given in detail

18、 in the SAE Dryseal Pipe Thread Standards. Sealant Coating: All fittings that have external pipe threads will be furnished with a pre-applied sealant coating on the pipe threads that meets the requirements of CEMS D-31. 5.0 MATERIAL: Body and stem: brass standard with manufacturer. Handle: steel or

19、brass standard with manufacturer. 6.0 DEFECTS: Fittings will be free from burrs, loose scale, sharp edges, eccentricity of diameters and all other defects which affect their serviceability. NUMBER: MPAPS S-L-61.101-GS/PL TITLE: Drain and Shut-Off Cocks REVISION: 1506 This document is restricted and

20、may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 4 7.0 DIMENSIONS AND PART LIST: 7.1 Drain Cocks: TYPE B 7.1.1 Approved: A Taper Pipe Thread 1/

21、8 1/4 1/4 A1 Full Thread Length .266 .406 .250 B Handle Length 1.000 1.000 CDrain Diameter .219 .219 C1 Drain Diameter .156 .156 .188 C11 Drain Diameter .188 .188 .219 D End to Hexagon .719 .719 .500 E Handle Height .281 .281 F Hexagon Thickness .406 .219 .156 K Shoulder Length .312 .500 .344 J Hexa

22、gon Width .531 .562 .562 G Overall Length (Closed) 1.156 1.156 .812 Material & Finish Part Numbers Brass, Plain 134519 141615 TYPE C 7.1.2 Approved: A Taper Pipe Thread 1/8 1/4 * 3/8 A1Full Thread Length .266 .344 * .406 B Handle Length 1.250 1.500 1.656 L Handle Diameter .219 .250 .312 C Drain Diam

23、eter .172 .203 .250 D Drain Diameter .188 .250 .344 E Body Length .547 .625 .750 F Hexagon Thickness .203 .188 .250 K Shoulder Length .344 .438 .500 J Hexagon Width .438 .562 .688 G Overall Length (Closed) .875 1.062 1.375 Material & Finish Part Numbers Brass, Plain 103647 * PTF Special Short See Op

24、tional Handle Designs, Style 1 PTF SAE Short STYLE 1 A B C G 1.125 .219 .438 .906 1.250 .250 .531 * Dimensions C and G have a tolerance of .031. Not optional. STYLE 2 A B C G 1.375 .344 .375 .938 NUMBER: MPAPS S-L-61.101-GS/PL TITLE: Drain and Shut-Off Cocks REVISION: 1506 This document is restricte

25、d and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 4 7.2 Shut-off Cocks: 7.2.1 Approved: Material & Finish Part Number Brass, Plain 148344

26、8.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/