NAVISTAR MPAPS S-M-2 101-GS PL-2015 Automotive Pipe Plugs and Filler Drain Plugs English Series (Noun Code 6400).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 8 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-M-2.101-GS/PL Former Designation: ESP-M-2.101-GS TITLE: Automotive Pipe Plugs and Filler Drain Plugs English Series (Noun Code 6400) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-M-2.101-GS - A

3、ugust 2006 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropri

4、ate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, PP, NPP. 1.0 GENERAL: This standard conforms to SAE Standard J531 and covers specifications and dimensions for those types of pipe, filler an

5、d drain plugs having tapered pipe threads which are commonly used in automotive and related industrial applications. 2.0 CONTENTS: 3.0 MISCELLANEOUS DIMENSIONS AND TOLERANCES: The tabulated dimensions will apply to the finished parts, plated, hardened or otherwise processed or specified by the purch

6、aser. Maximum taper on head of square head plugs will be minus four degrees total. Tolerance on dimensions not otherwise limited will be plus and minus .010 inch. The minimum across corners dimensions of external hexagons will be 1.092 times the nominal width across flats. The minimum across corners

7、 dimensions of external squares will be 1.25 times the nominal width across flats, but will not result in a side flat width of less than .75 times the nominal width across flats. At maximum material condition, the radii at corners of hexagon and square sockets in broached and upset plugs will not ex

8、ceed .005 inch. 4.0 THREADS: The pipe threads on Automotive Pipe Plugs, unless there is specific authorization to the contrary, will conform with the Dryseal American Standard Taper Pipe Thread (NPTF) and be gaged accordingly. The Automotive Pipe Plug dimensions are based on the length of the (NPTF)

9、 Page General 1 Miscellaneous Dimensions and Tolerances 1 Threads 1 Policy for Selecting Parts for New Design 2 Material 2 Finishes 2 Restricted Chemical Substances 2 Workmanship 3 Automotive Hexagon Head Pipe Plugs and Filler and Drain Plugs 3 Automotive Hexagon Socket Pipe Plugs and Drain Plugs 4

10、Automotive Square Socket Pipe Plugs and Drain Plugs 6 Automotive Square Socket Pipe Plugs and Filler and Drain Plugs 7 Technical Information 8 NUMBER: MPAPS S-M-2.101-GS/PL TITLE: Automotive Pipe Plugs and Filler Drain Plugs REVISION: 1506 This document is restricted and may not be sent outside Navi

11、star, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 8 thread and are intended for assembly with all types of Dryseal Taper and Straight Internal Pipe Threads. It is the conse

12、nsus of manufacturers and users that trouble-free assembly and pressure-tight joints without lubricant or sealer cannot be assured unless a full length of thread is used. The pipe threads on Automotive Filler and Drain Plugs, unless there is specific authorization to the contrary, will conform with

13、the Dryseal SAE Short Taper Pipe Thread (PTF-SAE Short) and be gaged accordingly. The Automotive Filler and Drain Plug dimensions are based on the length of the (PTF-SAE Short) thread and are primarily intended for assembly with Dryseal American Standard Taper (NPTF) or Dryseal American Standard Int

14、ermediate Straight (NPSI) internal pipe threads in installation where it is desirable to limit the entry of the small end of the plug. Limitation on other applications of this thread are explained in the SAE Dryseal Pipe Thread Standard. Pipe threads will be chamfered or rounded to the closest 1/64

15、inch diameter smaller than the minor diameter within a tolerance of minus .016 inch to produce approximately one incomplete thread and not to exceed one and one-half incomplete threads. The pipe threads on square and hexagon socket plugs will be full or complete for the overall length specified and

16、will be chamfered on both ends. Specifications for Dryseal pipe threads and related specifications covering blank sizes, dies or chasers, gages, gaging, etc., are given in detail in the SAE Dryseal Pipe Thread Standards. Sealant Coating: All fittings that have external pipe threads will be furnished

17、 with a pre-applied sealant coating on the pipe threads that meets the requirements of CEMS D-31. 5.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability, and cost savings in volume buying. For new

18、 design, parts shall be selected from “Approved“ part list only. Material: Brass (BRS) Finish: Plain (PLN) Design: Hex 6.0 MATERIAL: Plugs may be made by casting, forging, milling from the bar or upsetting from a grade of material free from defects that might affect their serviceability. Material wi

19、ll be as designated by part number per the specification called for below: Steel (STL) - Free-machining steel with 0.30% maximum carbon content. Malleable Iron (MI) - ASTM-Al97 or equivalent. Aluminum (AL) - Aluminum Association AA2011-T3, 2024-T351, 6061-T651 per MPAPS C-10. Cast Iron (CI) - CEMS E

20、-6 - Gray Iron, Grade 25-S. 7.0 FINISHES: As designated by part number, parts will be furnished plain, plated or coated in accordance with MPAPS and class listed below: Plain (PLN) Zinc Trivalent (ZN6A) MPAPS G-20, Class 6A Phosphate Coating (PHC) MPAPS G-1, Class 2 8.0 RESTRICTED CHEMICAL SUBSTANCE

21、S: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. NUMBER: MPAPS S-M-2.101-GS/PL TITLE: Automotive Pipe Plugs and Filler Drain Plugs REVISION: 1506 This document is restricted and may not be

22、sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 8 9.0 WORKMANSHIP: Parts will be free from burrs, loose scale, sharp edges, eccentricity of diameters and

23、 all other defects that may affect their serviceability. 10.0 AUTOMOTIVE HEXAGON HEAD PIPE PLUGS AND FILLER AND DRAIN PLUGS (NOUN CODE 6400): 10.1 Part List: 10.1.1 Approved: Dimensions in Inches: PIPE PLUGS B Dryseal Thread (NPTF) 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 C Shoulder Lengt

24、h .37 .37 .56 .56 .75 .75 .94 L Full Thread Length .30 .30 .46 .46 .61 .62 .77 D Head Width, Max .315 .440 .565 .690 .877 1.065 1.315 Head Width, Min .304 .428 .551 .674 .860 1.044 1.292 E Head Thickness, Max .162 .194 .194 .227 .227 .323 .323 Head Thickness, Min .151 .181 .181 .212 .212 .304 .304 S

25、 Recess Diameter, Max .10 .16 .25 .38 .50 .69 .88 T Wall Thickness, Min .09 .12 .12 .16 .16 .19 .19 Material & Finish PART NUMBERS Brass Plain (PLN) 444614 20988R1 20990R1 444632 444638 444644 Steel Zinc Trivalent (ZN6A) 444613 444619 Steel Plain (PLN) 444618 444624 444630 444636 444642 Dimensions i

26、n Inches: FILLER AND DRAIN PLUGS B Dryseal Thrd (PTF-SAE Short) 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 C Shoulder Length .32 .32 .49 .49 .64 .65 .81 L Full Thread Length .26 .27 .41 .41 .53 .55 .69 D Head Width, Max .315 .440 .565 .690 .877 1.065 1.315 Head Width, Min .304 .428 .551 .67

27、4 .860 1.044 1.292 E Head Thickness, Max .162 .194 .194 .227 .227 .323 .323 Head Thickness, Min .151 .181 .181 .212 .212 .304 .304 S Recess Diameter, Max .10 .16 .25 .38 .50 .69 .88 T Wall Thickness, Min .09 .12 .12 .16 .16 .19 .19 Material & Finish PART NUMBERS Brass Plain 444814 28641R1 NUMBER: MP

28、APS S-M-2.101-GS/PL TITLE: Automotive Pipe Plugs and Filler Drain Plugs REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar,

29、Inc. JUNE 2015 Page 4 of 8 11.0 AUTOMOTIVE HEXAGON SOCKET PIPE PLUGS AND DRAIN PLUGS (NOUN CODE - 6400): 11.1 Part List: 11.1.1 Approved: PIPE PLUGS Dimensions in Inches: B Dryseal Thread 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 C Overall Length, Max .310 .310 .475 .475 .630 .640 .790 Ove

30、rall Length, Min .290 .290 .445 .445 .590 .600 .750 D Socket Width, Min .156 .188 .250 .313 .375 .563 .625 Socket Width, Max (Cast) .161 .193 .255 .318 .380 .568 .630 D1Socket Width, Min ( Broached ) .156 .188 .250 .313 .375 .563 .625 Socket Width, Max ( or Upset ) .161 .193 .255 .318 .380 .568 .630

31、 F Drilled Hole Dia, Max (Non-Ferrous) .161 .193 .261 .323 .386 .570 .633 D1Socket Width, Min ( Broached ) .156 .187 .250 .312 .375 .562 .625 Socket Width, Max ( or Upset ) .158 .189 .252 .315 .378 .565 .629 F Drilled Hole Dia, Max ( Steel ) .161 .193 .255 .318 .381 .570 .633 P Socket Depth, Min .12

32、 .12 .19 .19 .25 .31 .38 T Wall Thickness, Min (1) .06 .08 .10 .13 .16 .18 .20 T Wall Thickness, Min (2) .06 .06 .07 .08 .09 .10 .11 L Wall Thickness, Min (3) .06 .06 .06 .06 .09 .09 .12 Material & Finish PART NUMBERS Brass Plain (PLN) 444689 444693 444699 444705 Steel Zinc Trivalent (ZN6A) 9409955

33、444688 444692 444698 Steel Plain (PLN) 9409954 444687 444691 444703 444709 (1) Use with cast. (2) Use with cast brass. (3) Use with broached and upset plugs. NUMBER: MPAPS S-M-2.101-GS/PL TITLE: Automotive Pipe Plugs and Filler Drain Plugs REVISION: 1506 This document is restricted and may not be se

34、nt outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 5 of 8 DRAIN PLUGS Dimensions in Inches: B Dryseal Thread (PTE-SAE Short) 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/

35、4-14 1-11-1/2 C Overall Length, Max .270 .280 .425 .425 .560 .570 .710 Overall Length, Min .250 .260 .395 .395 .520 .530 .670 D Socket Width, Min .156 .188 .250 .313 .375 .563 .625 Socket Width, Max (Cast) .161 .193 .255 .318 .380 .568 .630 D1 Socket Width, Min (Broached) .156 .188 .250 .313 .375 .5

36、63 .625 Socket Width, Max (or Upset ) .161 .193 .255 .318 .380 .568 .630 F Drilled Hole Dia, Max (Non-Ferrous) .161 .193 .261 .323 .386 .570 .633 D1Socket Width, Min (Broached or) .1562 .1875 .2500 .3125 .3750 .5625 .6250 Socket Width, Max (Upset ) .1582 .1895 .2520 .3155 .3780 .5655 .6200 F Drilled

37、 Hole Dia, Ma, ( Steel ) .161 .193 .255 .318 .381 .570 .633 P Socket Depth, Min .09 .09 .16 .16 .19 .31 .25 T Wall Thickness, Min (1) .06 .08 .10 .13 .16 .16 .20 T Wall Thickness, Min (2) .06 .06 .07 .08 .09 .10 .11 L Wall Thickness, Min (3) .06 .06 .06 .06 .09 .09 .12 Material & Finish Part Numbers

38、 Steel Zinc Trivalent (ZN6A) 444867 *Thread must be full or complete for entire length. (1) Use with cast or malleable iron. (2) Use with cast brass, bronze, or aluminum. (3) Use with broached and upset plugs. NUMBER: MPAPS S-M-2.101-GS/PL TITLE: Automotive Pipe Plugs and Filler Drain Plugs REVISION

39、: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 6 of 8 12.0 AUTOMOTIVE SQUARE SOCKET PIPE PLUGS AND DRAIN PL

40、UGS (Noun Code - 6400): 12.1 Part List: 12.1.1 Approved: Dimensions in Inches: PIPE PLUGS B Dryseal Thread (NPTF) 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-t/2 1-1/4 - 1-1/2- 11-1/2 11-1/2 C Overall Length, Max .310 .310 .475 .475 .630 .640 .790 .8437 .9062 Overall Length, Min .290 .290 .445 .

41、445 .590 .600 .750 .8125 .8438 D Socket Width, Min .13 .19 .26 .32 .38 .51 .51 .759 .759 Socket Width, Max .14 .21 .28 .35 .41 .54 .54 .764 .775 D Socket Width, Min (Broached) .130 .192 .255 .319 .381 .508 .508 .758 .758 Socket Width, Max (Or Upset) .135 .197 .260 .324 .387 .513 .513 .775 .775 F Dri

42、lled Hole Dia, Max .143 .209 .278 .345 .410 .553 .553 .812 .812 P Socket Depth, Min .12 .12 .19 .19 .25 .31 .38 .38 .38 T Wall Thickness, Min (1) .06 .08 .10 .13 .16 .18 .20 .22 .24 T Wall Thickness, Min (2) .06 .06 .07 .08 .09 .10 .11 .12 .13 L Wall Thickness, Min (3) .06 .06 .06 .06 .09 .09 .12 .1

43、99 .188 Material & Finish PART NUMBERS Steel Plain (PLN) 444650 444654 444660 445751 9409949 444678 Steel Zinc Trivalent (ZN6A) 444661 444667 273469 21502R1 Cast Iron Plain (PLN) 444664 9409947 20976R1 Malleable Iron Plain (PLN) 20980R1 9409948 Brass Plain (PLN) 444652 Dimensions in Inches: DRAIN PL

44、UGS Dryseal Thread (PTF-SAE Short) 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 B Overall Length, Max .270 .280 .425 .425 .560 .570 .710 Overall Length, Min .250 .260 .395 .395 .520 .530 .670 D Socket Width, Min .13 .19 .26 .32 .38 .51 .51 Socket Width, Max .14 .21 .28 .35 .41 .54 .54 D1Socke

45、t Width, Min (Broached) .130 .192 .255 .319 .382 .508 .508 Socket Width, Max (or Upset) .135 .197 .260 .324 .387 .513 .513 F Drilled Hole Dia, Max .143 .209 .278 .345 .410 .553 .553 P Socket Depth, Min .09 .09 .16 .16 .19 .19 .25 T Wall Thickness, Min (1) .06 .08 .10 .13 .16 .18 .20 T Wall Thickness

46、, Min (2) .06 .06 .07 .08 .09 .10 .11 L Wall Thickness, Min (3) .06 .06 .06 .06 .09 .09 .12 Material & Finish PART NUMBERS Steel Plain (PLN) 444776 444782 Steel Zinc Trivalent (ZN6A) 444783 444801 (1) Use with cast or malleable iron. (2) Use with cast brass, bronze, or aluminum. (3) Use with broache

47、d and upset plugs. NUMBER: MPAPS S-M-2.101-GS/PL TITLE: Automotive Pipe Plugs and Filler Drain Plugs REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent

48、liability. 2015 by Navistar, Inc. JUNE 2015 Page 7 of 8 13.0 AUTOMOTIVE SQUARE HEAD PIPE PLUGS AND FILLER AND DRAIN PLUGS (Noun Code - 6400): 13.1 Part List: 13.1.1 Approved: Dimensions in Inches: PIPE PLUGS 1-1/4 - 1-1/2- 2- B Dryseal Thread (NPTF) 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/

49、2 11-1/2 11-1/2 11-1/2 C Body Length, Max .350 .350 .525 .525 .700 .710 .870 .88 .91 .98 Body Length. Min .330 .330 .495 .495 .660 .670 .830 .85 .88 .93 L Full Thread Length .30 .30 .46 .46 .61 .62 .77 .80 .83 .88 D Head Width, Max .221 .283 .377 .440 .565 .627 .815 .938 1.125 1.312 Head Width, Min .214 .276 .370 .428