NAVISTAR MPAPS S-S-1 101-GS PL-2015 O-Rings C English Series (Noun Code C 7175).pdf

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 6 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-S-1.101-GS/PL Former Designation: ESP-S-1.101-GS TITLE: O-Rings English Series (Noun Code 7175) ) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ESP-S-1.101-GS - September 2000 PRINTED COPIES OF THIS

3、 DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices a

4、nd to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, PP. 1.0 GENERAL: Rings in this standard are restricted to those sizes in SAE J120a. Other sizes are considered design parts and must be specified on product engineering depar

5、tment drawings. For identification of materials, qualification requirements, color codes, and all other requirements not covered in this standard, see MPAPS K-15, Part II. 2.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification mu

6、st comply with the requirements of the MPAPS B-50 specification. 3.0 CONTENTS: Page General 1 Restricted Chemical Substances 2 Dimensions 2 Policy for Selecting Parts for New Design 2 O-Rings 3 O-Rings For Adjustable Straight Thread Fittings 6 Technical Information 6 NUMBER: MPAPS S-S-1.101-GS/PL TI

7、TLE: O-Rings REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 6 4.0 DIMENSIONS: Actual dimension

8、s are shown in this document. Dimensions shown on part number pages are nominal only. For gland dimensions, refer to Navistar Engineering Manual, EM9, Part I (Inch). CLASSIFICATION OF COMPOUNDS Designation Typical Material (Rubber) Hard- ness Shore A Application Resistant To Navistar Class Obsolete

9、IH Class Approx ASTM D 1418 Approx SAE J 200 ASTM D 2000 3 - EPDM CA ethylene propylene 70 Static nonmineral oils alcohols, brake fluids or fire resistant fluids such as phosphate esters 3A - EPDM CA ethylene propylene 90 Same as Class 3 -for use with greater pressures and more severe operating cond

10、itions. Same as Class 3 6 4 NBR BK nitrile 90 Same as Class 5 - for use with greater pressures and more severe operating conditions. Same as Class 5 7 - FPM HK fluoro- carbon 70 Static and Light Dynamic Duty and High Temperature Hydraulic Fluids, Fuels and Lubricants at tem- peratures -40F (-40C) to

11、 450F (230C) 8 - FPM HK fluoro- carbon 90 Same as Class 7 - for use with greater pressures. Same as Class 7 5.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability, and cost savings in volume buyin

12、g. For new design, parts shall be selected from “Approved“ part list only. NUMBER: MPAPS S-S-1.101-GS/PL TITLE: O-Rings REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to

13、 assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 6 6.0 O-RINGS (NOUN CODE - 7175): Size No. Actual Size Toler- ance .010 - Size No Actual Size 129 1.549 1.755 W = .070 .003 037 2.489 2.629 130 1.612 1.818 W = .139 .004 ID OD (Ref) 038 2.614 2.754 131 1.674 1.880 ID OD (Ref) T

14、oler- ance ,005 - Toler- ance .015 - 132 1.737 1.943 Toler- ance .006 006 .114 .254 039 2.739 2.879 133 1.799 2.005 210 .734 1.012 007 .145 .285 040 2.864 3.004 134 1.862 2.068 211 .796 1.074 008 .176 .316 041 2.989 3.129 135 1.925 2.131 212 .859 1.137 009 .208 .348 042 3.239 3.379 136 1.987 2.193 2

15、13 .921 1.199 010 .239 .379 043 3.489 3.629 137 2.050 2.256 214 .984 1.262 Oil .301 .441 044 3.739 3.879 138 2.112 2.318 215 1.046 1.324 012 .364 .504 045 3.989 4.129 139 2.175 2.381 216 1.109 1.387 140 2.237 2.443 013 .426 .566 Size No. Actual Size 141 2.300 2.506 217 1.171 1.449 014 .489 .629 W =

16、.103 .003 142 2.362 2.568 218 1.234 1.512 015 .551 .691 ID OD (Ref) 143 2.425 2.631 219 1.296 1.574 016 .614 .754 Toler- ance .005 - 144 2.487 2.693 220 1.359 1.637 017 .676 .816 110 .362 .568 145 2.550 2.756 221 1.421 1.699 018 .739 .879 111 .424 .630 146 2.612 2.818 Toler- ance .006 - 112 113 114

17、115 .487 .693 Toler- ance .015 - Toler- ance .010 - 019 .801 .941 .549 .755 147 2.675 2.881 223 1.609 1.887 020 .864 1.004 .612 .818 148 2.737 2.943 224 1.734 2.012 021 .926 1.066 .674 .880 149 . 2.800 3.006 225 1.859 2.137 022 .989 1.129 116 .737 .943 150 2.862 3.068 226 1.984 2.262 023 1.051 1.191

18、 Toler- ence .006 - 151 2.987 3.193 227 2.109 2.387 024 1.114 1.254 117 .799 1.005 152 3.237 3.442 228 2.234 2.512 025 1.176 1.316 118 .862 1.068 153 3.487 3.693 229 2.359 2.637 026 1.239 1.379 119 .924 1.130 154 3.737 3.943 230 2.484 2.762 027 1.301 1.441 120 .987 1.193 155 3.987 4.193 231 2.609 2.

19、887 028 1.364 1.504 121 1.049 1.255 156 4.237 4.443 Toler- ance .010 - 122 1.112 1.318 157 4.487 4.693 Toler- ance .015 - 029 1.489 1.629 123 1.174 1.380 158 4.737 4.943 232 2.734 3.012 030 1.614 1.754 124 1.237 1.443 159 4.987 5.193 233 2.859 3.137 031 1.739 1.879 125 1.299 1.505 Toler- ance .023 -

20、 234 2.984 3.262 032 1.864 2.004 126 1.362 1.568 160 5.237 5.442 235 3.109 3.387 033 1.989 2.129 127 1.424 1.630 161 5.487 5.693 236 3.234 3.512 034 2.114 2.254 128 1.487 1.693 162 5.737 5.943 237 3.359 3.637 035 2.239 2.379 163 5.987 6.193 036 2.364 2.504 NUMBER: MPAPS S-S-1.101-GS/PL TITLE: O-Ring

21、s REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 6 Dimensions in inches: (Continued) Size No.

22、Actual Size 273 9.734 10.012 Size No. Actual Size 457 13.975 14.525 W = .139 .004 274 9.984 10.262 458 14.475 15.025 ID OD (Ref) W = 275 .006 459 14.975 15.525 238 3.484 3.762 275 10.484 10.762 ID OD (Ref) 460 15.475 16.025 239 3.609 3.887 276 10.984 11.262 Toler- ance .015 - 240 3.734 4.012 277 11.

23、484 11.762 425 4.475 5.025 241 3.859 4.137 278 11.984 12.262 426 4.600 5.150 242 3.984 4.262 279 12.984 13.262 427 4.725 5.275 243 4.109 4.387 280 13.984 14.262 428 4.850 5.400 244 4.234 4.512 281 14.984 15.262 429 4.975 5.525 245 4.359 4.637 Toler- ance .023 - 246 4.484 4.762 Size No. Actual Size 4

24、30 5.100 5.650 247 4.609 4.887 W = .210 .005 431 5.225 5.775 248 4.734 5.012 ID OD (Ref) 432 5.350 5.900 249 4.859 5.137 Toler- ance .010 - 433 5.475 6.025 250 4.984 5.262 325 1.475 1.895 434 5.600 6.150 Toler- ance .023 - 326 1.600 2.020 435 5.725 6.275 251 5.109 5.387 327 1.725 2.145 436 5.850 6.4

25、00 252 5.234 5.512 328 1.850 2.270 437 5.975 6.525 253 5.359 5.637 329 1.975 2.395 438 6.225 6.775 254 5.484 5.762 330 2.100 2.520 439 6.475 7.025 255 5.609 5.887 331 2.225 2.645 440 6.725 7.275 256 5.734 6.012 332 2.350 2.770 441 6.975 7.525 257 5.859 6.137 333 2.475 2.895 258 5.984 6.262 334 2.600

26、 3.020 Toler- ance .030 - 259 6.234 6.512 Toler- ance .015 - 442 7.225 7.775 260 6.484 6.762 335 2.725 3.145 443 7.475 8.025 261 6.734 7.012 336 2.850 3.270 444 7.725 8.275 262 6.984 7.262 337 2.975 3.395 445 7.975 8.525 Toler- ance .030 - 338 3.100 3.520 446 8.475 9.025 263 7.234 7.512 339 3.225 3.

27、645 447 8.975 9.525 264 7.484 7.762 340 3.350 3.770 448 9.475 10.025 265 7.734 8.012 341 3.475 3.985 449 9.975 10.525 266 7.984 8.262 342 3.600 4.020 450 10.475 11.025 267 8.234 8.512 343 344 3.725 3.850 4.145 4.270 451 10.975 11.525 268 8.484 8.762 345 3.975 4.395 452 11.475 12.025 269 8.734 9.012

28、346 4.100 4.520 453 11.975 12.525 270 8.984 9.262 347 4.225 4.645 454 12.475 13.025 271 9.234 9.512 348 4.350 4.770 455 12.975 13.525 272 9.484 9.762 349 4.475 4.895 456 13.475 14.025 NUMBER: MPAPS S-S-1.101-GS/PL TITLE: O-Rings REVISION: 1506 This document is restricted and may not be sent outside

29、Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 5 of 6 6.1 Part List: 6.1.1 Approved: Size No. Width Nominal ID Material Class Part Number 007 1/16 5/32 5 361300R1 008 1/1

30、6 3/16 5 360599R1 009 1/16 7/32 5 3046105R1 010 1/16 1/4 5 352219R1 011 1/16 5/16 5 359158R1 012 1/16 3/8 3 875519C1 012 1/16 3/8 5 355967R1 013 1/16 7/16 3 875520C1 013 1/16 7/16 5 375271R1 015 1/16 9/16 3 875521C1 016 1/16 5/8 5 379181R1 018 1/16 3/4 5 574069R1 021 1/16 15/16 7 40091R1 022 1/16 1

31、5 377028R1 025 1/16 1 3/16 6 343901R1 034 1/16 2 1/8 5 28566R1 111 3/32 7/16 3 875522C1 111 3/32 7/16 5 355966R1 113 3/32 9/16 5 352221R1 114 3/32 5/8 5 350429R1 116 3/32 3/4 3 875524C1 118 3/32 7/8 5 364879R1 118 3/32 7/8 380839R1 119 3/32 15/16 5 362796R1 120 3/32 1 3 875525C1 124 3/32 1 1/4 5 379

32、794R1 124 3/32 1 1/4 7 40016R1 125 3/32 1 5/16 5 382418R1 132 3/32 1 3/4 5 382781R1 144 3/32 2 1/2 5 327110R1 144 3/32 2 1/2 6 26919R1 145 3/32 2 9/16 7 40092R1 Size No. Width Nominal ID Material Class Part Number 149 3/32 2 13/16 5 295204R1 150 3/32 2 7/8 5 22282R1 208 1/8 .609 7 40093R1 210 1/8 3/

33、4 5 350684R1 212 1/8 7/8 5 253070R1 214 1/8 1 5 350818R1 215 1/8 1 1/16 3 875528C1 215 1/8 1 1/16 5 254954R1 218 1/8 1 1/4 5 252483R1 218 1/8 1 1/4 7 40018R1 220 1/8 1 3/8 5 293739R1 223 1/8 1 5/8 5 360610R1 224 1/8 1 3/4 7 27400R1 225 1/8 1 7/8 3 21490R1 225 1/8 1 7/8 5 21924R1 227 1/8 2 1/8 5 2105

34、6R1 227 1/8 2 1/8 7 28349R1 233 1/8 2 7/8 7 26147R1 241 1/8 3 7/8 5 259246R1 242 1/8 4 5 468339R1 243 1/8 4 1/8 5 22411R1 246 1/8 4 1/2 5 3046999R1 249 1/8 4 7/8 5 22413R1 250 1/8 5 5 22414R1 254 1/8 5 1/2 5 285253R1 266 1/8 8 5 384149R1 325 3/16 1 1/2 5 22288R1 333 3/16 2 1/2 7 26164R1 334 3/16 2 5

35、/8 5 3044436R1 344 3/16 3 7/8 5 254688R1 443 1/4 7 1/2 5 22400R1 NUMBER: MPAPS S-S-1.101-GS/PL TITLE: O-Rings REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume al

36、l patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 6 of 6 7.0 O-RINGS FOR ADJUSTABLE STRAIGHT THREAD FITTINGS: Typical Fitting Installation Using Metal Washer 7.1 Part List: 7.1.1 Approved: Nominal Tube Size Actual O-Ring Size ID Tolerance Cross Section Width Class 6 Class 8 .125 .239 .005 .0

37、64 .003 .187 .301 40266R1 .250 .351 .072 .003 369751R1 27564R1 .312 .414 369384R1 .375 .468 .078 .003 364839R1 882779C1 .500 .644 .087 .003 876106C1 .625 .755 .097 .003 364885R1 876107C1 .750 .924 .006 .116 .004 876108C1 .875 1.048 1.000 1.171 876110C1 1.250 1.475 .010 .118 .004 877691C1 1.500 1.720

38、 876111C1 1.750 2.090 2.000 2.337 Note: Above O-Rings conform to sizes and dimensions shown in SAE J515a. All dimensions are in inches. For Classification of Compounds, see page 1 & 2. For identification of materials, qualification requirements, color codes, and all other requirements not covered in

39、 this standard, see MPAPS K-15, Part II. 8.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/