NAVY A-A-50391-1992 FOOTWEAR COVERS DISPOSABLE《一次性鞋套》.pdf

1、A-A-50391 84 9999974 00b7148 9 A-A-503 9 1 24 June 1992 FWIWEKRcoVERs, DISPOSABLE Ws Cornniescial item Wiption is authorized for use in preference to MIL-F-87023. Descrbtion - The footwear covers shall be a pull-on, disposable type of a single shape (for either foot) with an elastic top clocure, mad

2、e frm flexible vinyl film. All seams shall be heat sealed and the outsole shall have an embosced non-skid pattern. lhetopclosureshallbeturnedduwn 1-1/8 to 1-1/4 inch with an elastic tape inserted hefore heat seal-. Material - The basic material shall be vinyl film conforming to type I, class 1 of GP

3、-375. The thickness for the upper portion shall be 0.008 (it0.0008) inch. The thickness for the outsole shall be 0.040 (10.004) inch and tested as specified for the 0.020 inch film of i,+-375. me elastic tape for the top closure shall be of any cornmescial type suitable for the purpose intended and

4、shall be 5/8 (11/16) inch wide. The thrad used for joining the ens of the elastic tape shall be of any ccnmnercial type suitable for the purpose intended. The color of the tape and thread shall be white or natural. Beneficial connnents (recc9nmendations, additions, deletions) and any pertinent data

5、which may be of uce in improving this document should be addressed to: Facility, Post Office Box 59, Natick, MA 01760-0001 by using the self-addressed standardization Document improvement Proposal (DD Form 1426) appearing at the end of this document or by letter Offices in Charye, Navy Cloth- and Te

6、xtile F distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50391 84 9999974 0067149 O A-A-503 9 1 Sizes - The footwear covers shall be provided in the following sizes: Size Related shoe Size small Medium Large X-Large vp t

7、o and including size 6 Size hmver, if the working patterns are modified the design and nwxisurmts must be maintained as intended by government patterns. cannercia1 patterns may be used in lieu of government patterns provided they are approved for use by the goverment and confom to the cited design a

8、nd finished measwmts. Measurements - nie finished dimensions of the footwear covers shall be as indicated belm and Figure 1. All measurements are in inches. Small Medium Larse X-LarseTolerance (A) Top Flelaxed (Flat) 6 6 6 6 5 318 (B) Top Stretched (Flat) (min) 7 8 9 10 (C) Height (min) 11 11 11 11

9、(E) Height Toe (min) 21 4 4 4 4 (Dl Sole -nfJ-th Il 11-118 12-114 13-118 14 f 318 Sole Width (Widest Part) 4-3/4 5-1/4 5-7/8 6-5/8 f 318 - i/ 21 Measurement shall be the actual surface (flat) distance taken fran cole inclusive of sealed seam. edge to upper seam. workmanship. foreign matter removed.

10、?he finished footwcxr covers shall be thoroughly cleaned and 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50391 4 9999974 00b7150 7 A-A-503 91 product Demonctration Model. fferers are requiredto suhit footwear covers of their intenied produc

11、tion and style. product Demonstration Model will consist of units independently developed. Product Demnstration Models will be analyzed and evaluated by the government. Evaluation criteria an basis for award are contained in the soiicitation. moctuct Demonstsation Wels will be retained by the govern

12、ment. ne (i) product Demnstration Model approved by DPSC under the resultant contract will serve as a manufacturing standarforthecorrespondingprctionitems delivered under this contract. fferers are advisedthattheprochct Demonstration Model does not relieve the successful offerer of this respmsibiity

13、 to perform in accordance with the -cia1 item Description specified above. Rewonsibilitv for inwect ion. The supplier is responsible for assuring the product conforms to the req.xkememts. Footwear cover lotswillbe incpected to determine conformance with the Commercial Item Description and the succec

14、sfu offerers technical proposal as negotiated. Acceptability of footwear cover lots will be determined by the use of Y3ampling Prccedures and Tables for Inspection by AttributesIl, ANSI 21.4, published by the American Society for Quality control. sampling prcceiures will be designated by the Govenrm

15、ent at the time of award. The sample unit is one footwear cover. The footwear covers will be examined for comercial type defects only. Defect. footwear covers shall be examined for the following defects: any hole (including pin hole), cut, tear, blister or bubble, any crack, crater, crazing, rupture

16、, wrinkle or burn; any weak or thin spot; not material specified, any rough edge; excess material not trimmed after heat sealing; any spot or stain (outside); outsole walking surface not embossed with non-skid pattern; any open seam; inadequate heat seal i.e., seam can be easily pulled apart with mo

17、derate hard pressure; permanent size label crmitted; not cut or fabricated in accordance with the prluct demonstration midel; label miss-, incorrect, or illegible; measurement of item not as specified; and any variance not otherwise classified herein Ixrt at variance with the prduct demonctration mo

18、del. nie End Item Testing - The seams of the footwear covers shall be tested for bondability. The rnhimm bond strength shall be determined by the tensile strength test method in GP-375, but the breaking factor shall be the basis for conparicon. The recult shall be no less than 65% of the breaking fa

19、ctor of the .O08 inch film. The percent breaking strength shall be determined by the following: Break factor of bonded seam Break factor of ,008 inch film %Wreakingstrength = x 100 Preservation - Each pair of footwear covers, with the coles facing each other and reversed heel to toe, shall have the

20、uppers laid flat an then wrappe arcnm the soles and heels. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50373 84 7777974 0067353 7 A-A-50391 Packinq - Sixty (60) pair of footwear covers of one size only, preserved as specified above, shall b

21、e packed in a fiberboard shipping container assembled, closed, and reinforced conforming to type CF, class domectic, grade 275, variety SW or DW, style RSC-L, CSSC-L, or 0%-1 of PPP-B-636. me for the box liner shall conform to type CF, class domectic, variety SW or DW, grade 275 of PPP-B-636. Packag

22、es shall be packed flat, four in length, one in width, and fifteenindepthwithinthechipping container. nie container inside dimensions shall approximate 22 inches in length, 15 inches in width, and 11 inches in depth. Box closure shall be in accordance with method II of PPP-B-636. fiberboard Marking.

23、 in addition to any special marking required by the contract or order, unit packs, intemediate or exterior containers and palletized unit loads shall be marked in accordance with the requirementS of MLGSTD-129. Palletization. whesi specified in the contract, items packed as cpecified above, shall be

24、 palletized on 4-way entry pallet in accordance with load, type Ia of MlGSTD-147. Each prepared load shall be bonded with primary and cecondary straps in accordance with the bonding methodc C and D or Film bonding F or G. Pallet patterns shall be in accordance with the appsdix of MIGSTD-147. The pal

25、let shall be 4-way, type IV; type V, class 1, size 2; or type VI11 fabricated frm wood group I, II, or IV, grade A of NN-P-71, or 4-way, swle 1, size A, type I, class 1 fabricated frm wood qrq cpecified in MIGP-15011. Interlocking of loads shall be effected by reversing the pattern of each carse. if

26、 the container is of a size which does not conform to any of the patterns specified in MIGSID-147, the pallet pattern use shall first be approved by the contracting officer. custodian: Navy - Nu &view activity: DIA - CT 4 Preparing activity: Navy - Nu Project 8430-N402 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50371 84 M 7777774 0067152 O A-A-5039 1 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-