NAVY A-A-50565-1997 CABINET STORAGE WARDROBE THREE DRAWER [Superseded NAVY MIL-C-28580 C CANC NOTICE 1 NAVY MIL-C-28580 C NAVY MIL-C-28580 B NAVY MIL-C-28580 A NAVY MIL-C-28580 (1).pdf

1、INCH-POUNDA-A-50565January 17, 1997SUPERSEDINGMIL-C-28580C(YD)18 March 1991Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any datawhich may improve this document should be sent to: Commanding Officer (Code 1581), NavalConstruction Battalion Center, 1000 23rd Ave

2、nue, Port Hueneme, CA 93043-4301, by using theStandardization Document Improvement Proposal (DD Form 1426) appearing at the end of thisdocument or by letter.AMSC N/A FSC 7105DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.COMMERCIAL ITEM DESCRIPTIONCABINET, STORAGE;

3、WARDROBE, THREE DRAWERThe General Services Administration has authorized the use of this commercialitem description for all Federal agencies.1. SCOPE. This commercial item description covers one type and size three-drawer storagecabinet, for use with wardrobes in enlisted and officer personnel quart

4、ers.2. SALIENT CHARACTERISTICS.2.1 Design. Each cabinet shall consist essentially of three drawers, two sides, back, top, andnecessary framework. The cabinet overall dimensions shall be 20-inch (508 millimetre (mm)depth, 18-inch (457 mm) width, and 25-inch (635 mm) height. Drawer overall inside dime

5、nsionsshall be 16-inch (406 mm) depth, 14.75-inch (375 mm) width, and 5-inch (127 mm) height.2.2 Standard commercial product. The cabinet shall, as a minimum, be in accordance with therequirements of this commercial item description and shall be the manufacturers standardcommercial product. Addition

6、al or better features which are not specifically prohibited by thiscommercial item description but which are a part of the manufacturers standard commercialproduct, shall be included in the cabinet being furnished. A standard commercial product is aproduct which has been sold or is being currently o

7、ffered for sale on the commercial marketthrough advertisements or manufacturers catalogs, or brochures, and represents the latestproduction model.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5056522.3 Cabinet components. Cabinet component mate

8、rial shall be as follows. Material thicknessshall be as shown in table I.2.3.1 Case.2.3.1.1 Base. The base shall be solid hardwood with the front and back members full lengthpieces. The front shall be inset 1.50 inches (38 mm), and the back shall be inset 1.00-inch(25 mm).2.3.1.2 Sides. The sides sh

9、all be particleboard, plywood, or steel extended to the full height ofthe cabinet, less the top thickness. The front vertical edge of each side shall be covered with onecontinuous piece of plastic edge molding. The bottom of each side at the back shall be notched tomatch the inset of the back base,

10、to permit the cabinet to pass over a wardrobe metal framemember.2.3.1.3 Back. The back shall be plywood or hardboard extended from the cabinet top undersideto the bottom of the lower drawer bearer inset. The back shall be inset 1.00-inch (25 mm) deepby 1.50 inches (38 mm) high at the bottom.2.3.1.4

11、Top. The top shall be particleboard or plywood. A decorative laminated plastic shall bebonded to the top surface, and a nondecorative laminated plastic to the bottom surface. Plasticself-edging shall be used on the four edges, to match the top and drawer fronts in color andthickness.2.3.1.5 Drawer b

12、earer frames. The bearer frame front and back members shall be made of solidhardwood, full length pieces. The top bearer frame and the two intermediate bearer frames shallbe secured to the cabinet sides with aluminum angles and sheet metal screws. Each of the twointermediate bearer frames shall be f

13、urther secured with sheet metal screws. The bottom bearerframe shall be rested on the base and fastened thereto with sheet metal screws. As an alternateassembly method, the drawer bearer frames may be routed into the sides securely and permanentlyglued and further secured with angled sheet metal scr

14、ews.2.3.1.6 Laminated plastic sheets. Decorative laminated plastic sheets shall be approximately0.032-inch (0.81 mm) thick. Pattern, color, and finish shall be as specified (see 6.2).Nondecorative laminated plastic sheets shall be approximately 0.030-inch (0.76 mm) thick.2.3.1.7 Plastic edge molding

15、 Plastic edge molding shall be provided with a convex face which issmooth, without grooves or other detail. A color shall be provided to match the exterior color ofthe sides.2.3.2 Drawers.2.3.2.1 Fronts. The drawer fronts shall be particleboard or plywood. When wood frame designis used, the inner d

16、rawer front shall be solid wood.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5056532.3.2.2 Bottoms. The drawer bottoms shall be wood, hardboard, or steel.2.3.2.3 Frame members, sides, and back. The frame members, drawer sides, and back shall b

17、ewood or steel.TABLE I. Cabinet components - minimum thickness.Particleboard Plywood Solid wood Hardboard SteelPart inch (mm) inch (mm) inch (mm) inch (mm) (gage)CASETop 0.75 (19) 0.75 (19) - - - - -Sides 0.75 (19) 0.75 (19) - - - - 20Back - - 0.25 (6) - - 0.25 (6) 20Base - - - - 1.50x1.50 - - -(38x

18、38)Drawer Bearer Frame - - - - 0.75x1.50 - - -(19x38)Drawer Side Suspension - - - - - - - - 14Vertical Stiffeners - - - - - - - - 20Cross Rails - - - - - - - - 18DRAWERFront 0.63 (16) 0.75* (19*) - - - -Inner Front - - - - 0.44 (11) - - -Sides - - - - 0.44 (11) - - 20Back - - - - 0.44 (11) - - 20Bot

19、tom - - 0.75 (6) - - 0.25 (6.35) 20*Thickness when inner front not used.2.3.3 Drawer guides.2.3.3.1 Center guide. For wood drawer bodies, the center guide shall be an all-metal type withan inner and outer track which operates on two sets of ball bearings.2.3.3.2 Side suspension. For steel drawer bod

20、ies, the side suspension shall be an outer and innerchannel of 14-gage steel with plastic guide on each side of the drawer. The center section of theouter channel at the rear shall be clipped and bent forward providing a tab-type stop, and thebottom section shall be punched and a two-prong insert-ty

21、pe plastic guide shall be inserted. Theinner channel shall be provided with an integral drawer stop and a plastic guide at the rear with arubber bumper.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5056542.3.4 Drawer pulls. Drawer pulls shall b

22、e aluminum or steel and fastened to the rear of thedrawer front, with not less than three equally spaced sheet metal screws. Drawer pulls shall berounded to avoid sharp corners.2.3.5 Drawer alignment. Two drawer stops shall be secured, one at each side of the drawer, tothe drawer bearer frame back m

23、ember to keep the drawer front in alignment, and to preventmarring the finish on the front of the drawer bearer frame member.2.3.6 Brackets. Two brackets of aluminum or steel shall be provided for securing the base to thewardrobe bottom. The brackets shall be located and secured, one on each side. A

24、dditionalscrews shall be provided for securing the brackets to the wardrobe bottom.2.4 Bonding. Adhesive shall be applied to joining surfaces in an adequate and uniform manner asrecommended by the adhesive manufacturer. The materials shall be clamped and pressed inaccordance with the adhesive manufa

25、cturers instructions. Laminated plastic sheets shall bebonded to plywood or particleboard with a urea-resin type adhesive.2.5 Finishes.2.5.1 Exposed wood parts. The exterior surfaces of the sides, front edge of the frame members,and the base front edge shall be filled and sanded. Two-coats of a one-

26、component, air-drying, oil-modified, pigmented polyurethane resin coating of the color specified shall be applied (see 6.2).The coating shall have a gloss range of 45 to 65 when measured with a 60 degree glossmeter.The coating shall be applied in accordance with the manufacturers instructions.2.5.2

27、Unexposed wood parts. Unexposed wood parts shall be sealed with a sealer, sanded,wiped clean, and finished with a coat of lacquer. Alternatively, all drawer surfaces, except fronts,may be coated by spraying or dipping into a drawer sealant. The drawer sealant shall be made ofa solution of wax and re

28、sins with not less than 30 percent nonvolatile matter of which not lessthan 7 percent is wax. A nongrain-raising sealant shall be used which is substantially colorless andafter drying, substantially odorless and nonstaining. Excess sealant shall be drained off. Inaddition, the drawers running surfac

29、es shall be coated with paraffin to insure ease of operation.2.5.3 Steel coatings and finish. All cabinet components fabricated from steel shall be treated,coated, and finished as specified below:2.5.3.1 Primer coatings. All treated components that are to be finish coated shall be given onecoat of p

30、rimer, applied dry-film thickness shall be not greater than 0.7 mil (0.002 mm). Theprimer shall be baked for not less than 45 minutes at a temperature of 250 degrees Fahrenheit (F)(121 degrees Celsius (C) or an equivalent baking period as recommended by the paintmanufacturer.2.5.3.2 Finish coat. Unl

31、ess specified by the contracting officer (see 6.2), all treated steel surfacesshall be finished in accordance with 2.5.3.2.1 or 2.5.3.2.2. Paint color shall be as specified(see 6.2).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5056552.5.3.2.1

32、Semi-gloss enamel finish. When the semi-gloss enamel finish is to be applied, all primedsurfaces shall be finished with a coat of semi-gloss enamel. The enamel shall be baked for not lessthan 45 minutes at 250 F (121 C) or an equivalent baking period as recommended by the paintmanufacturer.2.5.3.2.2

33、 Thermoset dry-epoxy powder finish. When the dry-epoxy powder finish is to beapplied, the epoxy powder shall be epoxy-ester or epoxy-polyester with a specific gravity range of1.5 to 1.8. The epoxy powder shall be applied with electrostatic airless spray equipment. Themetal, curing temperature, curin

34、g time, and application voltage shall be as prescribed by themanufacturer of the epoxy powder. The dry-film thickness shall be not less than 1.5 mil(0.04 mm). The epoxy powder shall be Glidden (Pulvalure Epoxy or epoxy-polyester powder),H.B. Fuller (Kativo Epoxy or epoxy-polyester powder), or other

35、equivalent products.2.5.4 Painted finishes. Painted finishes shall be smooth and without dirt, dust, or other foreignmatter embedded. The finishes shall not be discolored, rippled, peeled, have sags or runs. Smallscratches or areas of marred finish shall be touched up as necessary to match the surro

36、undingfinish. Large areas that are scratched or marred, affecting the appearance of the finish, shall bereplaced or the entire component refinished.3. REGULATORY REQUIREMENTS.3.1 Materials. The offeror/contractor is encouraged to use recovered materials to the maximumextent practicable, in accordanc

37、e with paragraph 23.403 of the Federal Acquisition Regulation(FAR). Unless otherwise specified herein, all equipment, material, and articles incorporated in thework covered by this commercial item description are to be new and fabricated using materialsproduced from recovered materials to the maximu

38、m extent possible without jeopardizing theintended use. The term “recovered materials” means materials which have been collected orrecovered from solid waste and reprocessed to become a source of raw materials, as opposed tovirgin raw materials. Unless otherwise specified, none of the above shall be

39、 interpreted to meanthat the use of used or rebuilt products are allowed under this commercial item description.3.2 Metric products. Products manufactured to metric dimensions will be considered on an equalbasis with those manufactured using inch-pound units, provided they fall within specifiedtoler

40、ances using conversion tables contained in the latest version of FED-STD-376B, and all otherrequirements of this commercial item description including form, fit and function are met. If aproduct is manufactured to metric dimensions and those dimensions exceed the tolerancesspecified in the inch-poun

41、d units, a request should be made to the contracting officer to determineif the product is acceptable. The contracting officer has the option of accepting or rejecting theproduct.4. QUALITY ASSURANCE PROVISIONS.4.1 Product conformance. The products provided shall meet the salient characteristics of

42、thiscommercial item description, conform to the producers own drawings, specifications, standards,Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-505656and quality assurance practices, and be the same product offered for sale in the commercialmar

43、ket. The government reserves the right to require proof of such conformance.5. PACKAGING. The preservation, packing, and marking shall be as specified in the contract ororder.6. NOTES.6.1 Source of documents.6.1.1 Copies of specifications and standards required by suppliers in connection with specif

44、icprocurement functions should be obtained from the procuring activity or as directed by thecontracting officer.6.1.2 The Federal Acquisition Regulation (FAR) is available from the Superintendent ofDocuments, U.S. Government Printing Office, Washington, DC 20402.6.2 Ordering data. Acquisition docume

45、nts should specify the following:a. Pattern, color, and finish of plastic laminated sheets (see 2.3.1.6).b. Color for the cabinet sides, and front frame members (see 2.5.1 and 2.5.3.2).c. When type of finish coat is to be specified (see 2.5.3.2).6.3 Subject term (key word) listing.CabinetParticleboa

46、rdStorageWoodMILITARY INTEREST: CIVIL AGENCY COORDINATING ACTIVITY:Custodian: GSA - FSSNavy - YD1 PREPARING ACTIVITY:Navy - YD1(Project 7105-0285)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTION

47、S1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and revision letter should begiven.2. The submitter of this form must complete blocks 4, 5, 6, and 7.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This

48、form may not be used to request copies of documents, nor to request waivers, or clarification of requirements on currentcontracts. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenceddocument(s) or to amend contractual requirements.I RECOMME

49、ND A CHANGE: 1. DOCUMENT NUMBERA-A-50565 2. DOCUMENT DATE (YYMMDD)3. DOCUMENT TITLECABINET, STORAGE; WARDROBE, THREE DRAWER4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.)5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(2) AUTOVON(if