NAVY A-A-50602-1993 SELF-LUBRICATED BEARINGS《自动润滑轴承》.pdf

1、A-A-50602 m 9999974 0344552 043 m a Beneficial comments (recommendations, additions, deletions) and any pertinent? data which may be of use in improving this document should be addressed to: Commander, SEA 05442, Naval Sea Systems Command, National Center Building 3, Washington, DC 20362-5160 by usi

2、ng the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. INCH-POUND A-A- 50602 5 April 1993 COMMERCIAL ITEM DESCRIPTION SELF-LUBRICATED BEARINGS The General Services Administration has authorized the use of this Commercial Item Descripti

3、on (CID), 1. Abstract. This CID covers self-lubricated journal or spherical bearings intended to replace grease lubricated bearings on submarines in underwater, oscillatory applications. 2. Salient characteristics. Bearings furnished under this CID shall comply with the following requirements, when

4、tested as specified in section 4, Quality Assurance Provisions. 2.1 Materials of construction. 2.1.1 Journal bearings shall consist of (a) A high strength backing and a low friction (metallic or nonmetallic) liner. The liner shall be not less than 0.010 inch thick. (b) A homogeneous low friction non

5、metallic material. 2.1.2 Spherical bearings shall consist of the same materials as the journal bearings. between the ball OD and the outer ring and between the ball ID and the mating surface. Low friction material shall be utilized 2.1.3 When metallic backed bearings are provided with the metallic m

6、aterial in direct contact with surrounding structural material, the metallic material shall be galvanically compatible with alloy steel per MIL-S-23284, class 1 and MIL-S-16216. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50602 9 5599974 0344

7、553 T88 9 2.3 2.4 2.5 2.6 2.7 2.8 2.9 A-A- 50602 Axial static limit load. For spherical bearings, the axial static limit load shall not be less than 6,000 pounds. Permanent set shall be less than 0.005 inch. Self-aliEnment - requirement. Spherical bearings shall be self- aligning and shall permit at

8、 least 3 degrees angular misalignment. Friction. The coefficient of friction of a journal bearing pre- loaded to 5000 psi shall be not more than 0.13. m. Total wear for any one sample shall not exceed 0.005 inch following testing IAW (see 4.6). Water absorption. After submersion in salt water (see 4

9、7), weight gain shall be not more than 1.5 percent, and swell shall be not more than O. 5 percent. Liner peelability and bond integrity. After completion of water absorption testing, the same samples shall be tested for liner peelability and bond integrity. The liner shall be evaluated as per MIL-B

10、81934. The liner shall be tightly adhered to the backing over at least 90 percent of the contact area and shall exhibit an average peel strength of not less than 2.0 pounds per inch for fabric type liners. The remaining adhesive on the backing after peeling the liner shall have no voids with diamet

11、ers larger than 25 percent of the race width or 0.25 inch whichever is smaller. In the event the liner cannot be removed without employing chipping scraping or abrasive techniques, the liner shall be considered to be properly bonded and free of voids and shall be classed as non- peelable. Not applic

12、able for bearings constructed per 2.1.1(b). CreeD. Bearing shall be loaded per 4.6 and held at 25,000 psi for 1000 hours and shall have a total permanent set over that period not greater than 0.003 inch. 2.10 Shock. The bearing material will pass applicable shock require- ments by successfully compl

13、eting the radial static load test. 3. Contractor certification. The contractor shall certify and maintain substantial evidence that the product offered meets the salient characteristics of the Commercial Item Description and that the product conforms to the producers own drawings, specifications, st

14、andards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 4. Oualitv assurance Drovisions. Unless otherwise specified, to determine com

15、pliance with the requirements of the salient characteristics section perform the following tests on condidate bearings. Journal bearings should be 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50602 H 9997774 0344554 914 A-A- 50602 sized per

16、M81934/1-16X016. Tolerances specified in M81934 and MS14102 are not required to be met for testing candidate bearings. Spherical bearings should be sized per MS14102-16. 4.1 Material of construction. Examine materials used in construction and determine thicknesses of layers. 4.2 Radial static limit

17、load. Determine the radial static limit load for a journal bearing as specified in the MIL-B-81934 radial static load test. For spherical bearings the radial static load test specified in MIL-B-81820 axial static load test. static limit load and permanent set shall be as defined in 2.2. The radial 4

18、3 Axial static limit load. Determine the axial static limit load on a spherical bearing as specified in the MIL-B-81820 axial static load test. The axial static limit load and permanent set shall be as defined in 2.3. 4.4 Self-alitmment requirement. Spherical bearings must be self-align- ing as def

19、ined in 2.4. 4.5 Friction. Preload a journal bearing to 5000 psi (based on projected area) in ASTM D 1141 synthetic seawater, and determine the fric- tional coefficients by measuring the breakaway torque. 4.6 Wear. Determine wear by the following procedure using a test rig in accordance with 4.6.1.1

20、 4.6.1 Procedure. Load the samples to 1000 psi based on projected area. Oscillate the shaft at plus or minus 45 degrees for 100,000 cycles. One cycle shall consist of a shaft rotating from zero to plus 45 degrees, return through zero to minus 45 degrees, then to zero. Samples shall be tested at a r

21、ate of 20 cycles a minute minimum. Load new samples to 5000 psi. For these samples, oscillate the shaft at plus or minus 45 degrees for 20,000 cycles. Determine the wear in these samples by comparing before and after thicknesses. 4.6.1.1 Use a test rig similar to the one specified for radial static

22、limit load testing in MIL-B-81934 for journal bearings or MIL-B-81820 for spherical bearings. The test rig should be modified so the bearing under test is immersed in ASTM D 1141 synthetic seawater. The bearing under test shall be installed into a steel housing using a class FN2 fit per ANSI B4.1. A

23、 hardened shaft (R 50 minimum) with a surface finish of 16 rms polished shall be used. sized to provide a class RC6 fit per ANSI B4.1. The shaft shall be 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50602 999997q OlqL1555 850 = A-A-50602 4.7

24、 Water absorotion. Weigh and measure the size of the tested bearing. The bearings should then be placed in ASTM D 1141 synthetic sea- water at 700 psi for three (3) months. Determine weight gain and dimensional swell. 4.8 Liner Deelabilitv and bond intenritv. Determine liner peelability and bond int

25、egrity as specified in MIL-B-81934. Samples to be tested shall have completed water absorption testing prior to per- forming this test. 4.9 Creep. Load a bearing in a test rig as in 4.6 above to 25,000 psi and hold at pressure for 1000 hours. Determine the permanent set. 4.10 Shock. The bearing mate

26、rial will pass applicable shock require- ments by successfully completing the radial static load test. 5. Metric Droducts. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within the tolerances specifie

27、d using conversion tables contained in the latest revision of FED-STD-376, and all other requirements of this Commercial Item Description are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made

28、to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. 6. Rewlatorv requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent pr

29、actical. 7. Inspection of Rackaaing. Sample packs and the inspection of packaging (preservation, packing and marking) for shipment, stowage and storage shall be in accordance with the requirements of packaging and the documents specified therein. 7.1 Packaging 7.2 Commercial. Packaging and marking s

30、hall be in accordance with ASTM D 3951. 7.3 Militarv. The packaging (preservation, packing and marking) requirements shall be in accordance with MIL-B-197 for the level of preservation (A or C) the level of packing (A, B or C) and marking and other packaging acquisitioning options therein, as specif

31、ied in the acquisitioning document. the following shall apply: In addition for Navy acquisitions, 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50b02 9999974 0344556 797 m A-A- 50602 (a) Lumber and plywood. Unless otherwise specified in the c

32、ontract or purchase order, all lumber and plywood including laminated veneer materials used in shipping container and pallet con- struction, members, blocking, bracing, and reinforcing shall be fire-retardant treated materials conforming to MIL-L-19140 as follows: Level A and B - Type II - weather r

33、esistant Category 1 - general use Level C and Commercial - Type I - Nonweather resistant Category 1 - general use (b) Fiberboard. Fiberboard used in the construction of interior (unit and intermediate) and exterior fiberboard boxes includ- ing interior packaging forms shall conform to the class-dome

34、s- tic/fire retardant or class-weather resistant/fire retardant materials requirements as specified in the contract or purchase order, of PPP-F-320 and amendments thereto. 8. NOTES 8.1 Ordering data. Purchaser must specify the following: (a) Title, number and date of this commercial item description

35、 (b) Type of bearing desired (journal or spherical). (c) Dimensions of bearing desired. 8.2 Acceptable suppliers. The below listed manufacturers are currently qualified to this commercial item description. Manufacturers desiring listing of their products should submit test data that demonstrates co

36、mpliance with this specification. (a) Rexnord Corporation 2324 Curtiss St. Downers Grove, IL 60515-4017 (b) Kamatics Corporation P O Box 3 Bloomfield, CT 06002 8.3 Copies of the federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk,

37、Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-50602 9999974 0344557 623 A-A-50602 8.4 Unless otherwise specified, the issues of referenced documents are those listed in the issue

38、of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. Custodians: Army - AT Navy - SH Air Force - 99 Preparing activity: Navy - SH (Project 3120-0725) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-