NAVY A-A-59220-1998 WRENCHES OPEN END AND WRENCH ASSEMBLY STAMPED STEEL [Superseded NAVY MIL-W-10698 C CANC NOTICE 2 NAVY MIL-W-10698 C VALID NOTICE 1 NAVY MIL-W-10698 C (1) NAVY MW-1.pdf

1、 A-A-59220 W 9038054 0000288 T93 INCH-POUND A-A-59220 Mav 18,1998 SUPERSEDING 30 September 1969 MIL-W-10698C COMMERCIAL ITEM DESCRIPTION WRENCHES, OPEN END, AND WRENCH ASSEMBLY, STAMPED STEEL The General Services Administration has authorized the use of this commercial item description by all Federa

2、l agencies. 1. SCOPE. This commercial item description (CID) covers stamped steel wrenches for light duty use. 2. CLASSIFICATION. Wrenches shall be in the following types and sizes, as specified (see 7.2): Type I - Double head, open end (see figure i). Size - 9/16-inch by 3/4-inch. Size - 3/8-inch b

3、y 9/16-inch. Size - 546-inch by 7/16-inch. Size - 1/4-inch by 7/16-inch. Type II - Alligator jaw and screwdriver (see figure 2). Size - 7/8-inch maximum. Type III - Wrench assembly (see figure 3). Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may

4、 improve this document should be sent to: Commanding Officer (Code 15E2), Naval Construction Battalion Center, 1000 23rd Avenue, Port Hueneme, CA 93043-4301, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NfA FSC 512

5、0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-59220 = 9038054 0000289 92T A-A-59220 3. SALIENT CHARACTERISTICS. 3.1 Descridon. Type I and type II wrenches are for light duty use in the servicing, adjustment, and maintenance of the M-41 and Y

6、ukon stoves. The type III wrench assembly is for use on the MlL-R-14601- Range and Accessory Outfit, Field, Gasoline; MIL-B-40098 - Bumer Unit, Gasoline Field Range ht, M-2; and MIGS-40608 - Stove, Gasoline, 2-Bumer. 3.2 Standard commercial product. The open end wrenches, and wrench assembly shall,

7、as a minimum, be in accordance with the requirements of his commercial item description and shall be the manufacturers standard commercial product. Additional or better fatures which are not. specifically prohibited by this commercial item description but which are a part of the mandacturers standar

8、d commercial product, shali be included in the open end wrenches being Mshed. A standard commercial product is a product which has been sold or is being currently offered for saie on the commercial market through advertisements or manufacturer s catalogs, or brochures, and represents the latest prod

9、uction model. 3.3 Material. Mteal shall be in accordance with the mandadurers standard practice using heat treated stamped steel. 3.3.1 Finish. The wrenches and wrench assembly shall be thoroughly cleaned of all rust, grease, and dirt. Wrenches shall have a corrosion-resistant finish. 3.4 Desim and

10、construction. Construction of wrenches including gas tip cleaner (see figure 4) shall be in accordance with the requirements specified herein and as shown in figures 1 through 4. 3.5 Markine for identification. Wrenches and wrench assembly shall be marked with the manufacturers name or readily ident

11、ifiable trademark. 3.6 work mans hi. All burrs and sharp edges shall be removed; parts shall operate without any binding or stlhess. 4. REGULATORY REQUREMENTS. 4.1 Recovered materials. The offeror/contractor is enwuraged to use recovered materials to the maximum extent practicable, in accordance wit

12、h paragraph 23.403 of the Federal Acquisition Regulation (FAR). Unless atherwise specified herein, all equipment, matenal, and articles incorporated in the work covered by this commercial item description are to be new and fabricated using materials produced from recovered materials to the maximum e

13、xtent possible without jeopardizing the intended use. The term “recavered materials” means materials which have been collected or recovered from solid waste and reprocessed to become a souce of raw maerials, as opposed to virgin raw materials. Unless othemise specified, none of the above shall be in

14、terpreted to mean that the use of used or rebuilt products are allowed under this commercial item description. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-59220 m 9038054 O000290 b4L m A-A-59220 4.2 Metric products. Products manufactured t

15、o metric dimensions will be considered on an equal basis with those manufhctured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest version of ASTM SI-10 (EEWASW SI-lo), and ail other requirements of this comercial item description

16、including form, fit, and finction are met. If a product is manufactured to metnc dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting ofcer has the optio

17、n of accepting or rejecting the product. 5. QUALITY ASSURANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the dient characteristics of this commercial item description, confom to the producers own drawings, specifications, standards, and quality assurance practices, and be

18、the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 6. PACKAGING. The preseivation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 Source of documents. 7.1.1 Copies of specifications r

19、equired by suppliers in connection with specific procurement functions should be obtained fim the procuring activity or as directed by the contracting officer. 7.1.2 The Federal Acquisition Regulation (FAR) is available fi-om the Superintendent of Documents, US. Government Printing Office, Washingto

20、n, DC 20402. 7.1.3 ASTM Standard is available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. 7.1.4 IEEE Standard is available from the Institute of Electrical and Electronics Engineers (IEEE), IEEE Service Center, 445 Hoes Lane, P.O. Box

21、 133 1, Piscataway, NJ 08855-133 1. 7.2 Ordering data. Acquisition documents shauld specis. the following: a. Title, number, and date of this document. b. Type and size required (see 2.). 7.3 Part Identification Number (PIN) . The following part identification numbering procedure is for government p

22、urposes and does not constitute a requirement for the contractor. The PIN to be used for items acquired to this description are created as follows: 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59220 = 9038054 00002L 588 M A-A-59220 AA59220 s

23、x Size (see 2. and 7.3.1) Type (see 2. and 7.3.1) CID number 7.3.1 PIN code identifier. A = Type I. B = Type II. C = Type III. 1 = Size 9/16-inch by 3/4-inch. 2 = Size 3/8-inch by 9/16-inch. 3 = Size 5/16-inch by 7/16-inch. 4 = Size 1/4-inch by 7/16-inch. 5 = Size 7/8-inch maximum. 7.4 Classificatio

24、n cross reference. Classifications used in this CID (see 2.) are identical to those found in the superseded Military Specification MIL-W-10698C. 7.5 SuDersession data. This CID replaces Military Specification MIL-W-1O698Cy NOTICE 1, dated 20 May 1987. 7.6 Metnc _products. The values states in either

25、 inch-pounds or SI units are to be regarded separately as stanard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shail be used independently of the other. Combining values fiom the two systems may result in non

26、-conformance with standard. 7.7 Subiectterm (?cy word) listing. Alligator jaw Double head MILITARY INTERESTS: CUStOdianS: Army-GL Navy - YD1 Air Force - 99 Review Activities: Air Force - 84 Nay - MC CIVE AGENCY COORDINATING ACTIVITY: GS A-F S S Praarinn Activity: Nv-YDl (Project 5120-0092) 4 Provide

27、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-59220 9038054 0000272 43lr 5.12 1.37 (130) t 4.63 4.37 (118) (111) 1.0 1.0 B (10) (10) 0.566-0.573 (14) (15) 0.375 (10) 0.562 (14) 0.44R (11) 0.29R (7) 0.62 (16) 0.75 L (8) (8) (6) (7) 0.440-0.446 0.440-0

28、.446 0.312 0.250 (8) (6) 0.437 0.437 (11) (11) 0.34R 0.34R (9) (9) 0.25R 0.20R (6) (5) 0.40 0.40 (10) (10) I 0.54 1 0.54 1 (11) (11) (11) (11) / A-A-59220 INDmINmARAcTERs .164 (8 GA) D A -J - K F LOCATION OF IDENTIFICATION MARKS 2 PL G/ 4.164 4 t C DIMENSIONS A inclles (mm) B C D E F G I J K L 9/16

29、X 314 7.62 (194) 1.62 (41) 1.25 (32) 0.565-0.578 (14) (15) 0.755-0.763 0.562 (14) 0.680 (17) 0.16R (4) 0.44R (11) 0.62 (16) 0.75 (19) (19) WRENCH SIZE 318x9116 I 5/16X7/16 I 114 X 7/16 0.378-0.384 0.316-0.322 0.253-0.267 FIGURE 1. Wrenches- open end. stamped steel. 5 Provided by IHSNot for ResaleNo

30、reproduction or networking permitted without license from IHS-,-,- A-A-59220 m 9018054 0000293 350 m A-A-59220 0.125 (3) -7 I-. VIEWA - 1.0 O. 125 t 1.94 (49) L0.136 (10 GA) (3) 1 c I FIGURE 2. Wrench alligatorfaW. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

31、e from IHS-,-,-a 3 A-A-59220 m 9038054 0000294 297 m A-A-59220 /- O. 125 - (3) O. 187 WRENCH ASSEMBLY 2 PL WRENCH FIGURE 3. Wrench and wrench assembly. stamped steel. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-0.156 R (4) A-A-59220 W 90LB054 O000295 123 W A-A-5 9220 0.142 -, i FIGURE 4. Cleaner. gas tiu. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-