NAVY A-A-59242-1998 EXCAVATORS CRAWLER MOUNTED DED HYDRAULICALLY OPERATED [Superseded NAVY OO-E-2772 CANC NOTICE 1 NAVY OO-E-2772]《液压操作DED带有履带式的挖掘机[取代 海军 OO-E-2772 CANC 公告1 海军 OO-E.pdf

1、A-A-59242 9038054 O000644 395 INCH-POUND A-A-59242 June 16.1998 SUPERSEDING May 14,1992 00-E-2772 COMMERCIAL ITEM DESCRIPTION EXCAVATORS, CRAWLER MOUNTED, DED, HYDRAULICALLY OPERATED The General Services Administration has authorized the use of this commercial item description for ail Federal agenci

2、es. 1. SCOPE. This commercial item description (CID) covers diesel-enginedriven, crawler mounted, hydraulically operated, excavators. The excavators covered by this CID are used in digging or moving loose gravel, sand, or hardpack soil. 2. CLASSIFICATION. The excavators shall be of the following typ

3、es and sizes as specified (see 7.2): Type I - Type II - Hoe type. Telescoping boom, type. Minimum over the side rated lifting capacity (SAE J 1097) I 1 I 2 II1 II2 II 3 6,500 pounds (lb) at 15-foot (fi) (2 948 kilograms (kg) at 4.6 metre (m) radius and ground level. 7,500 lb (3 402 kg) at 20-R (6.1

4、m) radius and ground level. 5,000 Ib (2 268 kg) at 15-ft (4.6 m) radius and ground level. 7,000 lb (3 175 kg) at 15-fi (4.6 m) radius and ground level. 12,000 lb (5 443 kg) at 15-ft (4.6 m) radius and ground level. NOTE: Radius equals any point through 360 degrees. Beneficial comments, recommendatio

5、ns, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Officer In Charge (Code 15E2), Seabee Logistics Center, 41 11 San Pedro St., Port Hueneme, CA 93043-4401, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing

6、 at the end of this document or by letter. AMSC NfA FSC 3805 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59242 = 9018054 O000645 221 A-A-59242 3. SALIENT CHARACTERISTICS. 3.1 Description. This CID consists of diesel-engine-driven, crawler mou

7、nted, fully revolving, upperstructure type excavators and allied equipment of conventional design, and heavy-duty construction. The excavators shall be complete with all necessary operating accessories customarily furnished with excavators of these types, whether stipulated herein or not. The excava

8、tor shall be capable of traveling over rough ground under adverse or severe conditions. 3.2 Standard commercial product. The excavators shall, as a minimum, be in accordance with the requirements of this CID and shall be the manufacturers standard commercial product. Additional or better features wh

9、ich are not specifically prohibited by this CID but which are a part of the manufacturers standard commercial product, shall be included in the excavators being furnished. A standard commercial product is a product which has been sold or is being currently offered for sale on the commercial market t

10、hrough advertisements or manufacturers catalogs, or brochures, and represents the latest production model. 3.3 Interchangeability. All excavators of the same classification fbmished with similar options under a specific contract shall be identical to the extent necessary to ensure interchangeability

11、 of component parts, assemblies, accessories, and spare parts. 3.4 Safety. The excavators shall comply with PCSA Standard No. 5 and OSHA regulations. All rotating or reciprocating parts and all parts subject to high operational temperature, that are of such a nature or are so located as to become a

12、hazard to the operating or attending personnel, shall be substantially guarded or insulated. The principal platform walking surfaces shall be of an antiskid type. Ladders, steps, and handholds shall be provided on the sides of the excavator cab or superstructure that entrance thereto and exit theref

13、rom may be unhampered and nonhazardous. Engine cooling fans shall be provided with guards. 3.4.1 Noise. When the noise level, measured in accordance with MIL-STD-1474, is greater than 85 decibels ( a request should be made to the contracting officer to determine if the product is acceptable. The con

14、tracting officer has the option of accepting or rejecting the product. 4. REGULATORY REQUIREMENTS. 4.1 Recovered materials. The offerorkontractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR

15、). 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-59242 Ol054 0000652 4bl A-A-59242 5. QUALITY ASSURANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, co

16、nform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 6. PACKAGING. The preservation, packing, and marking shall be as

17、 specified in the contract or order. 7. NOTES. 7.1 Source of documents. 7.1.1 Copies of specifications and standards required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer. 7.1.2 The Federal Acq

18、uisition Regulation (FAR) and Occupational Safety and Health Administration (OSHA) may be obtained fi-om the Superintendent of Documents, U.S. Government Printing Ofice, Washington, DC 20402. 7.1.3 ASTM Standards are available from the American Society for Testing and Materials, 100 Barr Harbor Driv

19、e, West Conshohocken, PA 19428-2959. 7.1.4 PCSA Standards are available from the Power Crane and Shovel Association, Marine Plaza, Suite 1700, 11 1 East Wisconsin Avenue, Milwaukee, WI 53202. 7.1.5 SAE Standards and Recommended Practices is available from the Society of Automotive Engineers, Inc., 4

20、00 Commonwealth Drive, Warrendale, PA 15096. 7.2 Ordering data. Acquisition documents should specie the following: a. b. d. e. f. g- h. C. 1. Title, number, and date of this CID. Type and size of excavator required (see 2.). When defroster and heater for revolving upperstructure cab is required (see

21、 3.6.1). Attachments required for each size of excavator (see 3.10). When a hydraulically operated impact hammer and tool bits are to be provided (see 3.10.1). Grade of diesel fuel engine is to operate on (see 3.13). When a toolbox is provided (see 3.14). When lifting and tiedown attachments are req

22、uired (see 3.15). When the excavator is to be configured for air transportation. Type of aircraft for which excavator is to be configured (see 3.16). 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - - - A-A-59242 9018054 0000653 3T8 t A-A-59242 j

23、 When the excavator is to be subjected to the rail impact test of MIL-STD-810 (see 3.17). k. Color of finish coat (see 3.19). 7.3 Part Identification Number (PIN) . The following part identification numbering procedure is for government purposes and does not constitute a requirement for the contrac

24、tor. The PIN used for items acquired to this description are created as follows: AA59242 X X CIDnumber I r T Type 1 Size PIN codes: i= Type1 2= Type2 A = Size 1 B = Size 2 C = Size 3 7.4 SuDersession data. This commercial item description replaces Federal Specification 00-E-2772, dated May 14, 1992.

25、 7.6 Classification cross reference. Classifications used in this commercial item description (see 2.) are identical to those found in the superseded Federal Specification 00-E-2772. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Navy - YDl Army - AT Review Activi es: ArmY-MT DLA-CC GSA - FSS Preparin? Activity: Navy - YD1 (Project 3805-0021) 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-