NAVY AND20006 REV 7-1989 DRIVE-TYPE XVI ENGINE ACCESSORY《驱动型十六发动机配件》.pdf

1、AND20006 REV 7 29 9939938 0000077 3 O.oOo?flW TO ,210 MU4 DEPTH. PITCH MI OF SPLW WLL RUN eOHCENlRXALLY WITH 9.WO PROVIOE CLEARANCE TO 1.094 MIN DEPTH FOR 8.500 MIN DIA FLANGE ADAPTER “T“Rw MOWTY(G FACE WIT“ .o06 FULL INMCATOR MOVEMENT (FIMI, KEEP 9,000 DIA TO ,406 MIN DEPTH FREE FROM ENOINC PARTS,

2、EXCEPT I I I/% SHAFT AND JAM ADAPTER WHEN USED. ROTATION CLOCKWISE FACINQ ENQINE PAD -.O40 MIN FULL THREAD W MAX RW (M CHAMFER OtL SEAL TO BE PROVIDED. TYPE GASKET MS9W WALL OR PLUG TYPE AND IIIETHOO THREAD ,375-24UNF-M SPECFICATW MIL-S-7742.12 STUDS. ALL EXPOSED PORTIONS EOUALLY SPACED ANO LOCATED

3、WITH xK)7 OF BASK POSITION IN RELATW TO 9.OW PLOT DIA / SEE DETAL A-A VIEW - SECTION A-A ITHE FACE OF THS DRIVE WL 6 VERTICAL WITHPI O WITH RESPECT TO THE LNQIHE HORUONTAL AM. 1.250 DIA 1 “A AT P.D. s!%uumu I SPLINE DATA 20/30 PITCH - 24 TEETH -. _. . . 39 PRESSORE AWLE SURFACE HAWNEW ROCKWLCL CW MI

4、N MM OEPTH OF EIFLCTIVF CASE .QM INACTIVE FOR NEW ESIGN AFTER 8 FEFI 1972 3 II 3 ? a O AND20006 AIR FORCENAVY AERONAUTICAL DESIGN STANDARD w. IAW- AS DRIVE-TYPE %VI ENGINE iAAAPnnAn“ - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ANDZ000b REV 7 29

5、 W 9997718 0000098 3 4. ;?;$ST &-AV FED.wcuE) 2995 45. SHEET 2 OF 2 DRIVE-TYPE XVI ENGINE ACCESSORY DETAIL A-A 714f 1. SPEED. SIRIhW, ICCESSGIII ITA AbJ UsW. - I I (a) +4OOi -00 RPH WHEN THE EHGIHE IS OPERATIHG AT 75% OF HDRHAL SEA LEVEL STATIC OUTPUT. (b) ACCESSORY CLEARII(CE SHALL BE PROVIDE0 IN A

6、CCORDAHCE WITH HAHUFACTURERS HODEL SPECIFICATIOH. PEQUIREHEHTS: IH ACCORDAHCE WITH ENGIHE SPECIFICATIOH. 1. ETZTERIAL 2. FINIS11 3. OESIG1 STREHSTH, THE ORIVE SHALL BE CAPABLE OF ORIVIHG COHTIHUOUS TORQUE LOAD (TC) AT AHY EHGIHE SPEED. THE ORIVE SHALL WITHSTAND THE STATlC TORVJE (1s) YITHT FAILURE O

7、F PEWENT DEFOWTIOH, AHD SHALL BE AOEWATE FOR FIVE (5) HINUTES PERIOO OF TORQUE OVERLOAD (To) OPERATIOH. OVERLOAD PERIODS SHALL BE COHSIOERED AS RECURRIHS AT FOUR (4) HOUR INTERVALS. 4. 5. KOTE: 1. 2. DIHENSIO!iS ARE IN IHCHES. UHLESS OTHEGiIISE SPECIFIED, TOLERANCES: DECIHALS .010. AHGLES P. TIE OIL

8、 LEAKAGE OUT OF THIS DRIVE Sti4LL HOT EXCEED 2 CC PER HOUR. PAD OUTLIHE AS DIREHSIOHED IS A BASIC HIHIHUH AREA REQUIREHEHT. _3 REEOVE ALL BURRS AND SHARP EDGES. 3, SPEED “S“ IS DRIVE SHAFT SPEED AT NOML RATED EHGINE SPEED UNLESS OTHERWISE HOTEO. 4. TIIIS DRAWING AHD THE APPLICABLE EHGINE SPECIFICATI

9、ONS, TOGETHER, CDHPLETELY DEFINE THE DESIGN REQUIREMENTS I 5. 6. DATA FOR TYPE XVI-S AH0 XVI-T, SEE HS18054. THE JAW ADAPTER HAS DELETED FOR CONVERTING TO TYPE XII EHGINE DRIVE DIHEHSIOHS. DRIVE (SEE AHDZOOOZ). FOR TYPE XII EHGIHE 7. IH THE EVEHT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND T

10、HE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDEHCE. O. REFEREHCED GOVERHLHT (OR NON-GOVERHHENT) MCUHEHTS OF THE ISSUE LISTE0 IH THAT ISSUE OF THE DEPARTHENT OF DEFENSE IHDEX OF SPECIFICAIOHS AND STANDARDS (DoDISS) SPECIFIED IH THE SOLICITATION FORCI A PART OF THIS STAHDARD TO THE EXTEHT SPECIFIED HEREIN. PROJECT HO. 2995-N163 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-