NAVY MIL-B-85252-1981 BALLONET CARTRIDGE ACTIVATED (MXU-695 B)《(MXU-695 B)子弹激活气囊》.pdf

1、MIL-B-85252(AS) T3 June 1981 MILITARY SPECIFICATION BALLONET, CARTRIDGE ACTIVATED * (MXU-695/B) This specification is approved for use by the Naval Air;Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE. 1.1 Scope.

2、 This specification establishes the requirements for manu- facture and acceptance of the MXU-695/B cartridge activated ballonet, critical item, referred to herein as the ballonet. 2. APPLICABLE DOCUMENTS; 2.1 Issues of documents. The following documents of the issue in effect on date OE invitation f

3、or bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS MILITARY MIL-S-487 MIL-W-5 25 74 Sulfur, Ground (for use in Ammunition). Welding Process and Welding Procedure Requirements for Manufacture of Equipment Utilizing Steel. MIL-B-8525 1 Bom

4、b, Binary Chemical, Empty, BLU-80/B. . MIL-C-85256 Cartridge, Impulse, CCU-l3/B. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: .Commanding Officer, Naval Air Engineering Center, Engineering Sp

5、ecifications and Standards Department (ESSD), Code 93, Lakehurst, NJ 08733, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document, or by letter. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

6、se from IHS-,-,-STANDARDS MI LI TARY MIL-STD- 105 MIL - sm- i O 9 MIL-STD-129 MIL-STD-810 MIL-STD-45662 DRAWINGS Naval Air Systems Command (Code Ident 30003) DL X4900552 . DL X49008il SA 2875561 X49 00623 0 Sampling Procedures and Tables for Inspection by Attributes. . Quality Assurance Terms and De

7、finitions. Marking for Shipping and Storage. Environmental Test Methods. Calibration System Requirements. Ballonet, MXU-695/B. Marking, Shipping, .and Storage for MXU-695/B. Ballonet Test Fixture. Tube , Injector. (Copies of specifications, standards, drawings, and publications re- quired by contrac

8、tors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise indi- cated, the issue

9、in effect on date of invitation for bids or request for proposal shall apply. DEPARTMENT OF TRANSPORTATION I. Code of Federal Regulations 49 CFR 171-178 . Transportation. (Application for copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, D.C. 2040

10、2.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-t b AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-E498-73 ASTM-E499 - 7 3 STM-1778-71 Standard Methods of Testing for Leaks Using the Mass Spectrometer Leak Detector or Residual Gas Analy

11、zer in the Tracer Probe Mode. Standard Methods of Testing for Leaks Using the Mass Spectrometer Leak Detector in the Detector Probe Mode. Standard Method for Calibration of Helium Leak Detectors by use of Secondary Standards. (Applications for copies should be addressed to the American Society for T

12、esting and Materials, 1916 Race Street, Philadelphia, PA 19103.) a 3. REQUIREMENTS. 3.1 Item description. The MXU-695/B ballonet consists of a welded tube assembly and a CCU-l3/B impulse cartridge. equally spaced longitudinal depressions each approximately 50 inches long. The depressions are packed

13、with lay-flat plastic tubes filled with a mixture of sulfur and silicon dioxide. The CCU-13/B impulse . cartridge contains the propellant and ignitor for expanding the depres- sions from the tubing during operation of the weapon. The tube contains three 3.2 Characteristics. 3.2.1 Performance. 3.2.1.

14、1 Solids load. There shall be no visual evidence of white and yell.ow separation areas or lumps, and the angle of repose shall be not greater than 45 degrees (deg). 3.2.1.2 Lay-flat tubing seal. There shall be no evidence of leaks from the lay-flat tbing surface or adhesive interface (see 4.4.2). 3.

15、2.1.3 Adhesive system peel strength. The peel strength shall be not less than 75 ounces (see 4.4.3). c 3 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-S252 13 777770b 03b4075 7 4 i: . . 3.2.1.4 Tube expansion. When the CCU-l3/B impulse cart

16、ridge, in accordance with MIL-C-85256(AS), is activated, the ballonet tube shall expand to fill the inside of volume of the injector tube basket. The expansion shall cause the material contained on the ballonet to be injected through the basket due to the rupture of the scored segments of the inject

17、or tube, Drawing X4900623. The ballonet shall not exhibit leakage in excess of loe4 atmospheres cubic centimeters per second at one atmosphere differential pressure and 25 +2 degrees Celsius (OC). 3.2.2 Environmental. The ballonet performance shall not be degraded below that specified in 3.2.1, nor

18、shall there be loose or damaged parts on the ballonet, separation of the lay-flat tubing from the adhesive, separation of the adhesive from the ballonet tube, holes or cracks in the lay-flat tubing, or evidence of blend separations as shown by dis- tinct white and yellow areas, after exposure to the

19、 following environ- ments. Also, the moisture and acidity contents of the blend shall be not greater than 0.1650 and 0.0023 percent by weight, respectively. The change of angle of repose between initial and final measurements at . 50 percent relative humidity shall be no greater than 22 deg. 3.2.2.1

20、 High temperature. Exposure to a high temperature of 74OC for 48 consecutive hours (see 4.4.5). 3.2.2.2 Low temperature. Exposure to a low temperatureof -48OC for 24 consecutive hours (see 4.4.6). 3.2.2.3 Vibration: Exposure to the vibration schedule of Figure 1 in each of the three mutually perpend

21、icular axes at a temperature of -4OOC (see 4.4.7). 3.2.2.4 Shock. Exposure to half sine wave impact shocks in each of three mueualiy perpendicular.axes having a peak amplitude of 15 gravity units (8) and a total duration of 11 milliseconds (ms) (see 4.4.8). 3.2.2.5 Humidity. .Exposure to a relative

22、humidity of up to 95 percent (see 4.4.9). 3.3 Design and construction. 3 :3.1 Production drawings. The ballonet shall be fabricated and assembled in accordance with the drawings, parts list, and other docu- ments listed on DL X4900552. 3.3.2 Standards of manufacture. All materials, processes, and pa

23、rts used in the manufacture of the ballonet shall be of high quality, func- tionally suitable for the application, and shall confrm strictly to the requirements specified in applicable documents and drawings ,referenced herein. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted w

24、ithout license from IHS-,-,-MIL-B-5252 13 = 3.3.2.1 Certification. When specified in the contract or purchase order, the contractor shall include written certification Co the pro- curing activity (see 6.2.2) , accompanied by ob jective quality evidence as defined in MIL-STD-109, that the materials,

25、processes, and parts used in the assembly meet the applicable requirements for each item. Further, the certification shall attest that the following ballonet subcomponents installed in each ballonet meet the requirements specified: Subcomponent Requirement Impulse Cartridge/CCU-l3/B MIL-C-85256 3.3.

26、2.2 Special working environments. Any special working environ- ments for the manufacture of ballonets shall be as specified in MIL-B-85251. e 3.3.2.3 Manufacturing processes and procedures. When specified in the contract or purchase order, the contractor shall prepare, in his own format, written pro

27、cedures for welding performed in the manufacture of the ballonet. The procedures shall be in accordance with MIL-W-52574. The procedures shall also reflect the requirements for welding specified on the applicable drawings as listed on DL X4900552. Copies of such procedures, together with referenced

28、documents, shall be made available to the procuring activity in the manner specified in the contract or purchase order (see 6.2.2) for technical concurrence. 3.4 First article. 3.4.1 Preproduction sample. Unless otherwise specified in the con- tract or purchase order (see 6.2.1), the number of sampl

29、e units to be submitted for preproduction testing shall be 10 ballonets, and one waterproof container of excess blend (10-pound minimum) prepsred for each lot of sulfur used in the 10 sample ballonet units. The prepro- duction sample shall be manufactured using the same methods, materials, processes

30、, and procedures proposed for production. Any production prior to acceptance of the preproduction sample shall be at the risk of the contractor. 3.4.2 Preproduction verification. At the discretion of the procuring activity.(see 6.2.1), preproduction verification shall be repeated under any:of the fo

31、llowing conditions: a. The manufacturer has modified his product (such as a change of raw materials, the process, production procedures, or methods). It shall be the responsibility of the contractor to notify the procuring activity prior to the incorporation of any such changes, and to provide quant

32、itative evidence of the effect of.such changes on the performance or character- istics of the product. Requirements for such tests shall be based on an evaluation of the evidence supplied. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-85252

33、 13 9999906 0364097 2 m. . e 8 b. Where there is evidence that the quality of the product has not been maintained, this evidence may be in the form of accumulated failure reports of the product, of system fail- ures attributable to the product, or failure of the product to pass any of the tests for

34、production lot acceptance that may be conducted by or for the procuring activity. c. Applicable documents have been amended or revised suffi- ciently so that continued validity of the previous prepro- duction testing is questionable. d. The manufacturer has not produced ballonets to this speci- fica

35、tion for a period of 12 months or longer. e. The manufacturer has changed. the location at which ballonets are produced. 3.5 Documentation. When specified in the contract or purchase order (see 6.2.1) , the following documents shall be prepared for the procuring activity : a. Certification (see 3.3.

36、2.1, 4.1.2.3, and 4.2.4). b Inspection reports (see 4.1.2.3 and 4.2.4). c. Manufacturing documentation (see 3.3.2,3). 3.6 Workmanship. The device shall be fabricated in a manner that will ensure compliance with all requirements of-this specification and the appropriate assembly drawings listed in Se

37、ction 2. There shall be no ekidence of wrinkles, kinks, creases, or scratches in the lay-flat tubing. Wrinkles are allowed at the tapered end sections. There shall be no evidence of separation of the lay-flat tubing from the ballonet tube. 4. QUALITY ASSURANCE PROVISIONS. 4.1 Responsibility for insp

38、ection. Unless otherwise specified in the contract or purchase order (see 6.2.1) , the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the con- tractor may use his own or any other faci

39、lities suitable for the perform- ance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections. cet forth in the specification where such inspections are . deemed necessary to assure supplies and servic

40、es conform to prescribed requirements. b 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-6-85252 13 993990b 03611098 4 - c I 4.1.1 Classification of inspections. The inspections of the ballonet shall be classified as follows: a. Preproduction t

41、ests (see 4.1.2). b. Quality conformance inspections (see 4.2). 4.1.2 Preproduction inspection. The preproduction sample of 3.4.1 shall be subjected to the inspections specified in Table I in the order shown. 4.1.2.1 Acceptance/rejection criteria. Failure of the materials to meet any of the requirem

42、ents shall be cause for rejection of the lot of material and all ballonets loaded with that lot of material. Any failure attributable to the ballonets shall cause rejection of the entire preproduction sample and preproduction lot. 4.1.2.2 ombined testing. Preproduction inspections of the ballonet an

43、d bomb, in accordance with MIL-B-85251, may be conducted concurrently upon approval of the procuring activity see -6.2.1). TABLE I. Preproduction inspection. Examination or test Group I Visual examination Lay-flat tube seal Adhesive system peel strength Girup II High temperature Low temperature ,_ V

44、ibration Shock Humidity Geoup III Adhesive system peel strength Lay-flat tube seal Functional Group IV (containers of excess) Solids load . Requirement 3.3.1, 3.6 3.2.1.2 3.2.1.3 3.2.2, 3.2.2.1 3.2.2, 3.2.2.2 3.2.2, 3.2.2.3 3.2.2, 3.2.2.4 3.2.2, 3.2.2.5 3.2.1.3 3.2.1.2 3.2.1.4 3.2.1.1 Test 4.4.1 4.4

45、.2 4.4.3 4.4.5 4.4.6 4.4.7 4.4.8 4.4.9 4.4.3 4.4.2 4.4.11 4.4.4 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-85252 13 97999Ob 03b4099 b lr c 4.1.2.3 Preproduction inspection report. When specified in the con- tract or purchase order (see 6

46、.2.2), results of the preproduction inspections shall be prepared for the procuring activity. The report shall contain the following information accompanied by a certification which attests that the information provided is correct and applicable to the product being submitted: a. A statement that th

47、e preproduction sample complies with all quality assurance provisions of this specification for the ballonet specified in the contract or purchase order. b. Number of units of product inspected. c. Results obtained for all inspections performed. d. Purchase descriptions or contract number and date,

48、together with an identification and date of changes. e. Certificates of compliance of all material procured directly by the contractor. f. Date submitted. The certification shall be signed by a responsible agent of the certi- fying organization. The certification shall be substantiated by evidence o

49、f the agents authority to bind his principal. of the agents authority will riot be required with subsequent certifi- cation unless, during the course of the contract, this authority is vested in another agent of the certifying orgahization. Substantiation 4.2 Quality conformance inspection, Quality conformance inspections shall be performed on each lot of ballonets offered for acceptapce. Tests shall be as specified in Table II i