NAVY MIL-C-17566 E-1988 CLOTH BILLIARD《台球布》.pdf

1、 MIL-C-175bbE 3 m 7977706 0380514 b m H-36- P MIL-C-17566E 31 May 1988 SUPERSEDING MIL-C- 17566D 4 October 1976 MILITARY SPECIFICATION CLOTH, BILLIARD This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers th

2、e requirements for a wool and nylon blend billiard cloth. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specif

3、ied, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited O in the solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of us

4、e in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardizati-on Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.

5、 AMSC FSC 8305 DISTRIBUTION STATEMENT A. - Approved for public release, distribution is unlimited. Licensed by Information Handling Services MIL-C-L7566E 3 7777906 0380535 MIL-C-17566E SPECIFICAlIONS FEDEHAL PPP-P-1132 - Packag2rig and Packing of Woolen, Worsted and Wool Blend (Synthetic Fiber; Cott

6、on) Fabrics MIL ITY MIL-C-43665 - Cloth, Woolr Mothproofing Treatment of STANDARDS FEDERAL FED-STD-191 - Textile Test Methods EIILITARY MIL-STD-655 - Provisions for Evaluating Quality of Cloth, Wool I and Wool Blends (Copies of specifications, standards, drawings, and publications required by contra

7、ctors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer . 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this sp

8、ecification to the extent specified herein. LAWS AND REGULATIONS Rules and Regulations Under the Wool Products Labeling Act of 1939 (Applicaton for copies should be addressed to the Federal Trade Commission, Washington, DC 20580.) 2.2 Other publications. The following document(s) form a part of this

9、 specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issue

10、 of the nongovernment documents which is current on the date of the solicitation. 2 Licensed by Information Handling ServicesMIL-C-L75bbE 83 W 7797706 0380536 T m . MIL-C-17566E TECHNICAL MANUAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS Method No. 8 - 1985 Colorfastness to Crocki

11、ng: AATCC Crockmeter Method (Gopies may obtained from AATCC National Headquarters, P.O. Box 12215, Research Triangle Park, NC 27709.) U.S. DEPARTMENT OF AGRICULTURE Methods of Test for Grade of Wool (Application for copies should be addressed to the U.S. Department of Agriculture, Agriculture Market

12、ing Service, Washington, DC 20402). 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulation

13、s unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Standard sample. The finished cloth shall match the standard and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.3). The standard sample is

14、 identified under piece number 88014. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material. 3.3.1 Fiber. 3.3.1.1 Wool. The wool stock shall be of fleece or pulled wool, or a combination o both, not lo

15、wer in grade than 56s U.S. Standard, when tested as specified in 4.4.1.1. The use of noils, laps or any other wool manufacturing by-products is prohibited. 3.3.1.2 Nylon. The nylon fiber shall be 3 denier, 2 inch staple, when tested as specified in 4.5. 3 Licensed by Information Handling Services- -

16、 MIL-C-L7566E 3 W 7777706 0380537 3 W a MIL-C-17566E 3.3.2 Yarn. The yarn shall be carded and spun on the woolen system and spun into singles for both the warp and the filling yarn, when tested as specified in 4.5. NOTE: Selvage yarn may be of a finer count than those used in the body of the cloth t

17、o prevent edges of the cloth from building up when rolled. The selvage yarn shall contain the same fibers as those used in the body of the cloth. 3.3.3 Fiber content. The finished cloth shall contain a minimum of 74 percent wool, with the: remaining percentage nylon, when tested as specified in 4.5.

18、 3.4 Color. The color of the finished cloth shall be Blue 3384 and shall match the standard sample. The color shall be obtained by stock or piece dyeing . 3.4.1 Matching. The finished cloth shall match the standard sample when viewed under filtered tungsten lamps which approximate artificial dayligh

19、t having a correlated color temperature of 7500 + 200 K, with illumination of 100 + 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 - + 200 K. (See 4.4.3.4.1). .3.4.2 Colorfastness. The finished cloth shall show colorfastness to wet dry cleaning

20、 and crocking equal to or better than the standard sample when tested as specified in 4.5. As a limit of acceptability when no standard sampe is available or when the standard sample is not referenced for colorfastness the finished cloth shall show a minimum of “good“ fastness to wet dry cleaning, a

21、nd shall show a crocking rating of 5.0 dry and 4.0 wet when tested. 3.5 Finish. The fabric shall be mothproofed, and have a finish and hand equal to or better than the standard sample when tested as specified in 4.4.3.4.1). The fabric shall be thoroughly scoured, properly fulled, free from vegetable

22、 matter ( carbonized if necessary) and face evenly sheared. 3.5.1 Mothproofing. The cloth shall be given a mothproofing treatment in accordance with MIL-C-43665, when tested as specified in 4.5. 3.6 Physical requirements. The finished cloth shall conform to the requirements specified in Table I when

23、 tested as specified in 4.5. 4 Licensed by Information Handling Services4 0 MIL-C-375bbE 83 = 777770b 0380538 3 MIL-C-17566E Table I. Phvsical reauirements Chara ct eris ti cs Maximum Minimum Weight., oz (kg) per linear yard (based on 56 inches) Yarns per inch (2.54 cm) warp filling Breaking strengt

24、h,lbs (N) warp filling - 15 (0.42) 47 (18.5) 40 (15.7) 86 (382.7) 78 (347.1) 3.7 Weave. The weave shall be 2 up, 1 down, left hand twill, when tested as specified in 4.5. 3.8 Width. The width of the finished cloth shall be as specified (see 6.2) and shall be the minimum acceptable width, exclusive o

25、f selvages. 3.9 pH. The pH value of the water extract of the finished cloth shall be no less than 4.0 nor more than 8.5 when tested as specified in 4.5. e 3.10 Length and put-up. Unless otherwise specified (see 6.2), the finished cloth shall be furnished in continuous lengths each not less than 50 y

26、ards (45.7 m). Each length shall be put-up on full width rolls face side inward as specified in PPP-P-1132. 3.11 Wool content label. Each piece shall be labeled, or ticketed for wool content in accordance with the Wool Products Labeling Act of 1939. 3.12 Back identification. The back side of the clo

27、th shall be identified by stamping on that side with the word “Back“ at each end of the roll. 3.13 Workmanship. The finished cloth shall conform to the quaxity esta9lish- ed by this document. The demerit points per 100 square yards (83.61 m ) when calculated as specified in Section 4, shall not exce

28、ed the established maximum point value. Each defect shall be marked with a 1 to 1-1/2 inch (2.54 to 3.81 cm) long string. The string shall be sewn into the selvage near the defect. A red string shall represent a three or four point defect and a white string shall represent a one or two point defect

29、(see 4.4.3.5). 5 . Licensed by Information Handling Services-_. MIL-Cl375bbE 83 9777906 0380539 5 - MIL-(2-175663 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection require

30、ments as specified herein. Except as otherwise specified in the contract or order, the contractor may use his own or any other facilities suitable for performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any o

31、f the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. I 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specifica

32、tion shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply

33、 with all requirements of the contract. Sampling in quality conformance daes not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.1.2 Certificate of compliance. Where certificates of compliance are

34、submitted, the Government reserves the right to check test such items, to determine the validity of the certification. 4.2 Classification of inspection, The inspection requirements specified herein are classified as follows: 1. First article inspection (see 4.3). 2. Quality conformance inspection (s

35、ee 4.4). 4.3 First article inspection. When required (see 3.2 and 6.2), the first article shall be visually examined for appearance, color and finish, and shall be tested for physical and chemical properties in accordance with methods specified in 4.5. 4.4 Quality conformance inspection. Sampling fo

36、r inspection shall be performed in accordance with MIL-STD-655, except where otherwise indicated. 4.4.1 Component and material inspection. In accordance with 4.1 above, components and materials shall be tested in accordance with all the requirements of referenced specifications, drawings, and standa

37、rds unless otherwise excluded, amended, modified, or qualified in this specification or Licensed by Information Handling ServicesNIL-C-17566E 83 9979906 0380520 1 m MIL-C-17566E 4.4.1.1 Wool. The wool shall be visually examined for grade in scoured form, prior to dyeing, picking, or carding by compa

38、rison with the applicable U.S. Standard (see 2.2). The examination for grade shall be performed on a composite sample of 1 pound (0.45 Kg) of scoured wool for each 10,000 pounds (4500 Kg) or faction thereof in the lot. The composite sample shall be selected from not less than 10 percent of the bags/

39、bales in the lot. In the event of a dispute resulting from the above comparisons, the grade shall be determined by the width method (wedge). The lot shall be unacceptable if one or more composite sample fails to meet the requirements of 3.3.1. Each lot shall consist of one grade of wool only. 4.4.2

40、In-process inspection. Inspection shall be made at any point or during any phase of the manufacturing process to assure that no laps, noils, or any other wool manufacturing by-products are used (see 3.3.1. i). The Government reserves the right to exclude from consideraton for acceptance any material

41、 for which the in-process inspection has indicated non-conformance. 4.4.3 Examination of the end item. Examination of the end item shall be in accordance with 4.4.3.1 through 4.4.3.5. 4.4.3.1 Yard-by-yard examination. The yard by yard examination shall be as specified in MIL-STD-655. The fabric qual

42、ity shall be quality level 15. 4.4.3.1.1 Limit for slubs and knots. Only those knots and slubs which exceed the limits shown on Sears Fabric Defect Scales (see 6.4), F for slubs or 2 as applicable, and E for knots, shall be scored. O 4.4.3.2 Examination for length. Examination for length shall be as

43、 specified in MIL-STD-655. 4.4.3.3 Examination for back marking and compliance with the Wool products Labeling Act. Examination for backing marking and compliance with the Wool Products Labeling Act shall be as specified in MIL-STD-655. 4.4.3.4 Examination for shade and finish. 4.4.3.4.1 Individual

44、rolls. Each roll in the lot shall be examined visually for shade match (see 3.4.1) and finish (see 3.5). A roll shall be unacceptable if it fails to meet the requirements for shade match and finish. The sample unit shall be a 4 inch by 20 inch swatch of the cloth. A sample unit shall be drawn from e

45、ach roll in the lot. 4.4.3.5 Examination for defect marking. Examination for defect marking shall be as specified in MIL-STD-655. 4.4.4 Examination of packaging requirements Examination shall be made in accordance with the provisions of PPP-P-1132 to determine that put-up and preservation, packing,

46、and marking comply with section 5 requirements. .- a 7 Licensed by Information Handling Services- _- MIL-C-175bbE 83 W 7777906 0380523 3 E i MIL-C- 17 56 6E 4.5 Tests. The methods of .testing specified in FED-STD-191, wherever applicable, and as listed in Table III shall be followed. The physical an

47、d chemical values specified in section 3 apply to the results of the determinations-made on a sample unit for test purposes as specified in the applicable test methods. The sample unit shall be 2 continuous yards full width of the finished cloth. The lot size shall be expressed in units of 1 yard (.

48、9m) each. The lot shall be unacceptable if one or more sample units fail to meet any test requirement; specified. All test reports shall contain the individual values utilitzed in expressing the final result. The sample size (number of sample units) shall be in accordance with the following: TABLE I

49、I. Sample size Lot size (yards) Sample size 800 or less 2 801 up to and including 22,000 3 22,001 and over 5 TABLE III. Test methods Re q u i re ment Test Characteristic paragraph method Wool grade 3.3-1.1 4.4-1.1 Nylon identification denier, staple 3.3.1.2 - i/ Fiber content L3a3 2101 Colorfastness to 2 Vet dry cleaning 3.4-2 Crock i ng 3-4.2 Mothproofing- 3-5.1 562 1 AATCC-TM-8-1985 2/ Weight: 3.6 5Q4 1 Yarns per inch 3,6 5050 Breaking strength 3.6 5100 Weave 3.7 Visual 3/ - PH 3.9 2 8 1 1 i/ A certificate of compliance shall be submitted and shall be acceptable f