NAVY MIL-C-20267 C-1983 CARRIER CLUB POLICEMAN-S COTTON WEBBING OLIVE DRAB (WITH DOUBLE HOOK)《草绿色棉花织的警棍运送器(有双钩的)》.pdf

1、- MIL-C-20267C BY 7779706 O382057 3 Beneficial comments (recommendations , additions , deletions) and any pertinent data which may be of use in improving this document should be addressed to the Commandant of the Marine Corps (LMA-1) , Headquarters , U. S. Marine Corps, Washington, D. C. 20380, by u

2、sing the self- addressed Standardization Document Improvement Proposal (DD Form 142 6 ) appearing at the end of this document or by letter. MILITARY SPECIFICATION 6 January 1983 SUPERSEDING MIL-C-202 67B (MC) 6 June 1966 CARRIER, CLUB, POLICEMANS: COTTON WEBBING, OLIVE DRAB (WITH DOUBLE HOOK) This s

3、pecification is approved for use by U. S. Marine Corps, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. 1. size 2. 2. SCOPE SCOPE. This specification covers requirements for one type and policemans club carrier made of olive drab cott

4、on webbing. APPLICABLE DOCUMENTS Government documents. 2.1.1 Specifications, standards and handbooks. Unless otherwise specified, the following specifications, standards, and handbooks of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) speci

5、fied in the solicitation form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL V-T-2 85 UU-P-268 DDD-L-2 O MILITARY MIL-W-5 30 - Thread, Polyester - Paper, Kraft, Wrapping - Label; For Clothing, Equipage, And Tentage (General Use) - Webbing , Textile , Cotton Gener

6、al Purpose, Natural Or In Colors FSC 8465 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-202b7C 84 U 777770b 0382058 5 9 MIL-C-20267C (MC) MIL-H-639 MIL-B- 17757 - Hooks (For Belts, Straps and Equipage - Box, Shipping, Fiberboard (Modular ite

7、ms) Sizes) , S TAMIARDS FEDERAL FED-STD-7 5 1 - Stitches, Seams, And Stitchings M ILITAY MIL-STD-105 MIL-STD-12 9 -Marking For Shipment And Storage - Sampling Procedures And Tables For Inspection By Attributes (Copies of specifications and standards required by suppliers in connection with specific

8、procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. Ths issues of the documents which are indicated as DoD adopted shall be

9、 the issue listed in the current DoDISS and the supplement thereto, if applicable. UNIFORM CLASSIFICATION COMMITTEE Uniform Freight Classification Rules (Application for copies should be addressed to the Uniform Classification Committee, 1106 South Riverside Plaza, Chicago, Illinois 60606 . ) LAWS A

10、ND REGULATIONS U. S. Postai Service Manuai (Application for copies of the manual should be addressed to the Superintendent of Documents, U. S. Government Printing Office, Washington, D. C. 20402.) NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applicat

11、ion for copies should be addressed to the American Trucking Association, Inc., Tariff Order Section, 1616 P Street, N. W., Washington, D. C. 20026.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-202b7C 4 W 77777Ob 0382057 7 MIL-C-20267C (MC

12、) Department of Defense (DoD) Standard Color Card of Official Standardized Shades for Sewing Threads 1968 (Application for copies should be addressed to the Color Association of the United States, Inc., 200 Madison Avenue, New York, New York 10016,) 2.3 Order of precedence. In the event of a conflic

13、t between the text of this specification and the references cited herein, the text of this specification shall take precedence. 3. REQUIREMENTS 3.1 Samples. Samples are furnished solely for guidance and information to the contractor (see 6.3). Variation from this specification may appear in the samp

14、le, in which case the specification shall govern. 3.2 Firs,t article. Unless otherwise specified (see 6.2), before production is commenced, the first article consisting of the number of finished club carriers specified by the procuring activity (see 6.2) shall be submitted, or made available, to the

15、 contracting officer or his authorized representative for approval. The approval of the first article authorizes the commencement of production, but does not relieve the supplier of responsibility for compliance with all provisions of this specification. The first article shall be manufactured by th

16、e supplier in the same facilities to be used for the manufacture of the production items. 3.3 Materials. 3.3.1 Webbing, cotton. The webbing shall be 2 inches wide, dyed olive drab shade No. 7, water repellent and mildew-resistant treated, conforming to type III, class 4 of MIL-W-530. 3.3.2 Thread, p

17、olyester. The thread shall be size Y, 4 ply conforming to type I, class 1, subclass A or type II, class 1, subclass A of V-T-285. 3.3.2.1 Color and colorfastness. The thread shall be dyed olive drab shade S-1 cable No. 66022, (See DoD Standard Color Card of Official Standardized Shades for Sewing Th

18、read, 1968. The dyed thread shall show good fastness to chlorine bleaching, laundering and weathering when tested as specified in V-T-285. 3.3.3 Hook, double, brass, black chemical finish. The hook shall conform to type I, class 1 of MIL-H-639. 3 Provided by IHSNot for ResaleNo reproduction or netwo

19、rking permitted without license from IHS-,-,-3.3.4 Label. Each club carrier shall have an identification label. with the item nomenclature, contract number and stock number. The label shall conform to type IV, class 5 of DDD-L-20, and shall be located on the back of the club carrier. The item nomenc

20、lature shall be Carrier, Club; Policemans: OD. 3.4 Design. The club carrier shall be the U.S. Marine Corps design shown in Figure 1, The club carrier shall have double hooks and webbing stitched to accommodate the club. 3.5 Construction, The construction shall conform in all respects to Figure 1 and

21、 as specified herein. The club carrier shall be manufactured - in accordance with the requirements specified herein. The supplier is not required to follow the exact sequence of operations, but all operations specified shall be used to manufacture the club carrier. 3.5.1 Stitches, seams and stitchin

22、gs. Stitches, seams and stitching types specified in Table I shall conform to FED-STD-751. The number of stitches per inch as specified in Table I indicates the minimum and maxi- mum number permitted. 3.5.1.1 Backstitching. Thread breaks in stitching shall be backstitched not less than 1 inch at eac

23、h break. Stitching shall be backstitched not less than 1/2 inch at the ends, except where ends are held down by other stitchings. Thread tension shall be maintained so that there will be no loose stitching and that the lock will be embedded in the center of the materials sewed. All thread ends shall

24、 be trimmed. 4 .*. i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-202b7C 8Li M 779970b 03820bL 5 U MIL-C-20267C(MC) TABLE 1 MANUFACTURING REQUIREMENTS OPERATION :ut ting . ut 2-inch webbing to proper lengths or component parts, one body part

25、 1 + 1/8 inches long and one carrier laTt 9-3/4 - + 1/8 inches long. ?old and stitch body part. L. Fold one end of body part ridthwise 3-3/8 + 1/8 inches and .nsert the doublehook in the fold, acing to the front. I. Stitch the two plies together as :lose as possible to the double hook .n the fold, w

26、ith three rows of ;titches as close as possible but iot on top of stitches. ?old and stitch carrier part. ?dd carrier part widthwise in half md stitch the two plies together Iith three rows of stitches as close is possible but not on top of stitches 2-3/8 + 1/8-1/16 inches Erom the folded end formin

27、g a loop. kssemble the carrier and body part. i* Turn up the long end of the body sart and butt to short end. b. Position the carrier loop on the Eront of the body part with both snds spread open and the lower edge of the loop even with the lower edge of body part, and with the ends of loop inserted

28、 in the body part. C. Stitch the loop to the body part through all plies with two rows of stitches as close as possible to the loop. Continue to stitch around the edges, forming a box type stitch as shown in Figure 1. - TCH Y PE - o1 O1 SEAM/ CH TYPE Sf-3 Sf -3 - STC t!, IN - -8 -8 4 4 14 /4 5 Provi

29、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-202b7C 84 m 3999906 03820b2 7 m MIL-C-2 02 6 7C (MC) 3.6 Finished measurements. The finished club carrier shall conform to 3.7 Workmanshi . The finished club carrier shall conform to the of defects ot

30、her than selected major defects shall not exceed the limits established by the applicable acceptable quality level (AQL). the measurements shown in Figure 1. quality -T-l+ o t e pro uct established by this specification. The occurrence 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspectio

31、n. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable for the performance of the inspection re

32、quirements specified herein, unless disapproved by the Government . The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements . 4.1.1 Certificate of

33、 compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. 4.2 Classification of inspection. The inspection requirements specified herein are classified as follows: 1. 2. First article inspec

34、tion (see 4.4) Quality conformance inspection (see 4.5) - 4.3 Inspection conditions. Unless otherwise specified, all inspections shall be performed in accoraance with the test conditions specified in MIL-STD- 105 . 4.4 First article inspection. When first article is required, inspection shall be mad

35、e of a completely fabricated club carrier for all provisions of this specification. 4.5 Quality conformance inspection. 4.5.1 Component and material inspection. In accordance with 4.1 above, components and materials shall b e inspected and tested in accordance with all the requirements of referenced

36、 specifications, drawings, and standards unless otherwise excluded, amended, modified or qualified in this specification or applicable purchase documents. 4.5.2 End item sampling examination. As a final step in the contractors production control plan, before formation of the lot, each carrier shall

37、be examined on an inspection table. After formation of the lot, the club carrier shall be examined for the defects listed in 4.5.2.1 and 4.5.2.2. AQLs shall be as indicated in 4.5.2.3. The sample unit shall be one club carrier. 6 I- I Provided by IHSNot for ResaleNo reproduction or networking permit

38、ted without license from IHS-,-,- - MIL-C-20267C 84 m 9779706 0382063 7 m MIL-C-2 02 6 7C (MC 4.5.2.1 Gemmi Defects. - General Defects shall be classified as follows: .- Examine -. . Webbing Seams and stitching NOTE: A sea one o broke SkiPP doubl shall sides Run-of f s (see open seams) Seam and type

39、s Stitch tension Defect a. Holes, cuts or teara. b. Other webbing defects, such as .brasion, slub, smash, broken end Ir pick: .seriously affecting service- ability or appearance. .affecting serviceability or appearance but not seriously. :. Edges frayed or scalloped; not irmly or tightly woven. I. B

40、roken or malformed; finish imitted; corroded areas; burrs or iharp edges which may cause injury .n handling. pen seams.: - Less than 1/2 inch. - 1/2 inch or more. shall be classified as open when more stitches joining a seam are or when two or more continuous stitches or run-Offs occur. On or triple

41、 stitched seams, a seam B considered open when one or more f a seam are open. Wrong seam or stitch type. Loose, resulting in a loosely exposed top or bobbin thread; tight, resulting in excessive tightness of webbing on seams. C 1 ass i fi c at i on Ma j o* X X X X X X Mj r B 7 Provided by IHSNot for

42、 ResaleNo reproduction or networking permitted without license from IHS-,-,-._ - - - MIL-C-20267C 8LJ W 7777706 03820611 O W Examine Stitches per inch NOTE: Varii inch up tl orde: - placc Stitching margin; stitching gage Stitching ends Thread breaks NOTE: Threi clas! Components and assembly _ Defect

43、 a. One to two stitches less than minimum specified. b. Three or more stitches less than minumum specified. C. One or more stitches in excess of maximum specified. ion in the number of stitches per caused by the ope rat or speeding machine and pulling the fabric in to sew aver heavy seams or heavy ,

44、 shall be classified as follows: ithin the major defect lassification - Minor defect ithin the minor defect lassification - No defect Not as specified, affecting serviceability or appearance. Backstitched less than 1/2 inch. Backstitched less than 1 inch. breaks not backstitched shall be fied as ope

45、n seams. a. Any component part omitted or not as specified; any required operation omitted (unless other- wise indicated herein). b. Any required row of stitching omitted : -seriously affecting service- -affecting serviceability but not ability. seriously. Maj or X X X Mj - A X - X X X or B 8 Provid

46、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-20267C 84 E 7777706 0382065 2 :. Boxstitching less than specified dimension by 1/8 or more. i. Needle chews. Examine I. Mends or darns. Marking Cleannes s Omitted, illegible, incorrect, nisplaced or not

47、 as specified. Defect a. Grease or oil stains, clearly noticeable. b . -seriously affecting appearance . -affecting appearance but not Spots or dirt marks: seriously. C. Thread ends not trimmed throughout. 9 C 1 ass if i c at ion Maj or Mi Ir B Provided by IHSNot for ResaleNo reproduction or network

48、ing permitted without license from IHS-,-,-MIL-C-20267C 4 m 777770b 0382066 Li m MIL-C-20267C (MC) 4.5.2.2 Size measurements. Any measurement deviating from the normal dimensions and tolerances specified in Figure 1 shall be scored as a defect . 4,5.2.3 Inspection levels and AQLs. The inspection lev

49、els and AQLs, expressed in defects per hundred units (DHU), shall be as follows: Examination Inspection level - AQL For defects applicable to II Major 2.5 4.5.2.1, visual characteristics. Total 6.5 For defects applicable to s-3 One 6.5 4.5.2.2, dimensional characteristics. class 4.5.2.4 Examination of packaging. An examination shall be made to determi