NAVY MIL-C-2202 H-1990 COVERALLS MEN-S COTTON SATEEN《男式棉锻连衣工作服》.pdf

1、MIL-C-2202H 20 March 1990 SUPERSEDING MIL-C-2202G 2 December 1981 MILITARY SPECIFICATION COVERALLS, MENS, COTTON, SATEEN This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for the manufac

2、turing of two types of mens cotton sateen coveralls. . 1.2 Classification. The coveralls shall be of the following types and sizes, as specified (see 6.2): Type I - Olive Green 107 Sizes: Small, Medium, Large, X-Large, XX-Large Type II - White Sizes: XXX-Small, XX-Small, X-Small, Small, Medium, Larg

3、e, X-Large, XX-Large 2. APPLICABLE DOCUMENTS 2.1 Government documents. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmo

4、re Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 8405 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. Provided by IHSNot for Resal

5、eNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2202H * 2.1 .l Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, ,the issues of these do

6、cuments shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL V-T-276 * NN-P-71 DDD-L-20 MILITARY MIL-C-3735 MIL-C-10296 * MIL-P-15011 MIL-B-17757 MIL-F-21840

7、MIL-T-43548 MIL-T-43566 STANDARDS FEDERAL FED-STD-751 MILITARY * MIL-STD-105 MIL-STD-129 * MIL-STD-147 MIL-STD-1668 - Thread, Cotton - Pallet, Material Handling, Wood, Stringer Construction, 2 Way and 4 Way (Partial) - Label; For Clothing, Equipage and Tentage (General Use) -. - Cuffs, Knit, Wrist a

8、nd Ankle, and Cloth, Knitted - Cloth, Sateen, Cotton - Pallet, Material Handling, Wood, Post Construction, - Boxes, Shipping, Fiberboard (Modular Sizes) - Fastener Tape, Hook and Loop, Synthetic - Thread, Polyester Core: Cotton-, Rayon-, or - Tape, Text.ile, Cotton, General Purpose, Natural or 4 Way

9、 Entry Polyester Covered in Colors - Stitches, Seams, and Stitchings - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage - Palletized Unit Loads - Provisions for Evaluating Qualitv of Cloth Coveralls Attributes * MIL-STD-2073-1 - DOD Materials Procedures foi Develop

10、ment and * MIL-STD-2073-2 Application of Packaging Requirements - Packaging Requirement Codes * (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelp

11、hia, PA 19111-5094.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2202H * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to th

12、e extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. U.S. POSTAL MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-0001.) * 2.2 Non-Government publications. The fo

13、llowing document(s) form a part of this document to the extent soecified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those iisted in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in

14、 the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification _ (Application for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street,

15、N.W., Washington, DC 20036-14041, UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, IL 60606-5808). * (Non-Government standards and other publicati

16、ons are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) * 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited

17、 herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see

18、6.3). Variations from this specification may appear in the sample in which case this specification shall govern. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2202H 3-2 First article. When specified the contractor shall furnish sample unit(

19、s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material. It is encouraged that recycled material be used when practical as long as it meets the requirements of this document. 3.3.1 Basic material, 3.3.1.1 Type I coverall. The basic material shall be a cotton sateen, dyed Olive G

20、reen 107, conforming t class 1 of MIL-C-10296. 3.3-1.2 Type II coverall. The basic material shall be a cotton sateen, bleached white, conforming to class 2 of MIL-C-10296. 3.3.2 Cuffs, wrist and ankle (Type II coverall). The cuffs shall be aramid, natural shade or white, conforming to type IV, class

21、 1, size 1 for ankle cuffs and type IV, class 2, size 2 for the wrist cuffs of MIL-C-3735. 3.3.3 Thread. 3.3.3.1 Thread, polyester, cotton-covered. The thread for seaming and stitching shall be a polyester core, cotton-covered or rayon-covered thread conforming to ticket No. 30 and 50, 2 or 3 ply of

22、 MIL-T-43548. The color of the thread shall approximate the color of - the basic material of the appropriate type coverall. The use of polyester-covered polyester core thread is not allowed. _. .- . 3.3.3.1.1 Colorfastness. The dyed thread shall show colorfastness to laundering and light equal to or

23、 better than the standard sample when tested as specified in MIL-T-43548. As a limit of acceptability, or when no standard is available, the dyed thread shall show a minimum of lfgoodlf colorfastness to laundering and light when tested as specified in MIL-T-43548. 3.3.3.2 Thread, cotton. As an alter

24、nate, a cotton .thread, conforming to V-T-276, may be used for stitching and seaming. The color of the thread shall approximate the color of the basic material of the appropriate type coverall. The types and sizes of the thread shall be as follows: Coverall - Use Type Ticket No. - Ply Type 1 Seaming

25、 IA3 Type II Seaming IA2 30, 50 3 30, 50 3 3.3.3.2.1 Colorfastness. The dyed thread shall show colorfastness to laundering and light equal to or better than the standard sample when tested as specified in V-T-276, As a limit of acceptability, or when no standard sample is available, the dyed thread

26、shall show a minimum of llgoodll colorfastness to laundering and light when tested as specified in V-T-276. * 3.3.4 Label. Each coverall shall have a combination identification/ size/instruction label conforming to type VI, class 14 of DDD-L-20. Label inscription shall show fastness to laundering, I

27、nscription of label shall be as specified below: 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2202H 4 m 7777906 0435839 2 1z- =-_=_L_ c - MIL-C-2202H Name of Item: Coveralls, Mens, Cotton, Sateen, Type I (Example) Fiber Content: 100% Cotto

28、n Contract No: DLA-100-00-0-0000 (Example) Stock No: 8405-00-000-0000 (Example) Size: Medium (Example) Name of Contractor: Name of Manufacturer: (If other than contractor) Laundering Instructions FASTEN ALL FASTENER TAPES BEFORE LAUNDERING Hand or Machine Wash, Hot Tumble Dry, Medium OR Use NAVEDTRA

29、 414-01-45-81, Formula II: Hot Formula without Bleach ( 140 F) - .- 3.3.5 Ta e cotton. The cotton tape used as an alternate ?or the waist and 107, conforming to type I, class 3 of MIL-T-43566, except that colorfastness to crocking and weathering are not required. leg tabs _E_jl_ on t e type I covera

30、ll shall be 1-1/4 inch in width, dyed Olive Green 3.3.6 Tape, fastener. The fastener tape for the coverall shall conform to type II, class 1 of MIL-F-21840. The width of both the hook and loop portions of the tape shall be 1 inch wide. The color shall approximate the shade of the basic material (see

31、 3.3.1.1 and 3.3.1.2). * 3.4 Design. The type I coverall shall be one piece, with a protective hook and loop fastener flap type front closure, shirt style collar, one breast patch pocket with flap, two front patch pockets, one hip pocket, one rule pocket, a pass thru pocket, adjustment tabs on sleev

32、es and adjustment straps on waist and legs (see Figure 1). The type II coverall shall be one piece with a hook and loop fastener type front fly closure and knitted wristlets and cuffs. The type II coverall shall be pocketless (see Figure 2). 3.4.1 Figures. The figures are furnished for information p

33、urposes only. When any inconsistancies between the written specification and the figures exist, the written specification shall govern. * 3.5 Patterns. Standard patterns to be used to cut working patterns will be furnish- the Government (see 6.3). The working pat terns shall be identical to the Gove

34、rnment patterns. Neither the Government patterns nor the working patterns shall be altered in any way, except that additional notches for use during construction are permitted on the working patterns. Minor modifications are permitted where necessary when using automatic equipment. These modificatio

35、ns shall not alter the appearance, serviceability, or dimensional. requirements cited in the specification. Unless otherwise specified in Table I seam allowances shall be as follows: All double needle joining seams - 112 inch Facings to fronts .- 1/4 inch All other seams - 3/8 inch 5 Provided by IHS

36、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-_-I-_ - _ MIL-C-2202H 4 W 773330b - 0435840 3 W MIL-C-2202H * 3.5.1 List of pattern parts. The component parts of the coveralls shall be cut from the basic material in accordance with the pattern parts indicated below

37、: Ma terial Pattern Parts Cut Parts Shirt (Type I) Trouser (Type I) Shirt (Type II) Trouser (Type II) Back (one piece) or Back (two pieces) Front Collar (top and under) Topsleeve Undersleeve or Sleeve (one piece) Protective flap Lapel facing Breast pocket Breast pocket flap 1 2 2 2 1/ 2 2 2 1 2 1 -2

38、 - Back Front Front pocket Hip pocket Rule pocket Leg and waist tabs Pass-thru flap We1 t 2 2 2 1 1 2 2 4 - 21 Back (one piece) or Back (two pieces) Front Collar (top and under) Topsleeve Undersleeve or Sleeve (one piece) Front facings Back Front 1 2 2 2 1/ 2 2 2 2 - 2 2 Templates (Type I) Finished

39、breast pocket Finished breast pocket flap Right front inside fastener location marker Front fastener tape location marker Leg tab location marker (front and back) - 1/ Pattern may be cut in one piece, see operation 5e. - 2/ A cotton tape may be used as an alternate, see operation 15e. 6 Provided by

40、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-2202H 84 m 9999906 0435843 O m MIL-C-2202H 3.6 Construction. 3.6.1 Stitch, seam and stitching types. Stitch, seam and stitching types specified in Table I shall conform to FED-STD-751. Wherever two or more me

41、thods for seam or stitch types are given for the same part of the operation, any one may be used. Where stitch type 401 is used, the looper (underthread) shall be on the inside of the coveralls. Seam allowances shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats, or ope

42、n seams will result. Unless otherwise specified, top or edge stitching shall be 1/16 to 1/8 inch from edge, hook and loop fastener tape stitching shall be 1/16 to 1/8 inch from edge of tape, and all double needle stitching shall be 1/4 inch gauge with the row of stitching next to the folded edge not

43、 hore than 1/16 to 118 inch from edge. Where 515, 516 or 519 are specified, the cover thread shall be the same type as the looper thread, the lock or chainstitch portion shall be 3/8 inch from the raw edge and the bight of the overedge stitch portion shall be 3/16 to 1/4 inch. 3.6.2 Stitches per inc

44、h. The minimum and maximum number of stitches per inch shall be as specified in Table i. 3.6.3 Thread breaks and ends of seams. Ends of all seams and stitchings when not caught in other seams or stitching shall be backtacked not less than 318 inch. The ends of a continuous line of stitching shall be

45、 overlapped not less than 112 inch. Thread breaks (all stitch types) shall be repaired by stitching not less than 1/2 inch beyond each end of the break. Skipped stitches or 401 stitch type thread breaks may be repaired by using 301 stitch type* 3.7 Manufacturing operations requirements. The coverall

46、s shall be manufactured in accordance with the operati.on requirements specified in Table I. The contractor is not required to-follow the exact sequence of operations. Minor modifications are permitted where necessary when using automatic equipment. These modifications shall not alter the dimensiona

47、l, serviceability, or appearance requirements cited in the specification. 3.7.1 Shade and size marking. The component parts shall be marked, ticketed, or bundled to insure a uniform shade and size throughout the coverall. Any method of shade and size marking may be used except: 1. Corrosive metal de

48、vices. 2. Sew-on shade tickets. 3. Adhesive type tickets whose adhesive causes discoloration or whose adhesive mass adheres to the material upon removal of the tickets. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2202H * 3.7.2 Abbreviatio

49、ns in table of operations. Table I are as follows: Stch - in - Ndl - Bob - LPr Mchne - Brtck - Comrcl - smlr - Btnhl - incl - dbl - chnstch - - Stitch inch Needle Bobbin Looper Machine Bartack Comme r c ia1 similar Buttonhole including double chainstitch The abbreviations used in a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2202H TABLE