NAVY MIL-C-23023 B-1969 CLEANER STEAM PRESSURE JET TRAILER MOUNTED《高压喷气发动机拖车装置清洁器》.pdf

1、N-ILf-ll MIL-C-23023B (MC) - 22 May 1969 SUPERSEDING MIL-C-23023A(MC) 1 June 1964 MILITARY SPECIFICATION CLEANER, STEAM, PRESSURE JET, TRAILER MOUNTED 1. SCOPE 1.1 This specification covers one type of trailer mounted, gasoline engine driven, steam cleaner designed to remove surface,deposits of fore

2、ign material by means of a forced stream of steam and water or steam, water, and detergent. 2. APPLICABLE DOCUMENTS *2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of the specification to the extent specified herein. SPEC1 FICAT

3、 IONS FEDERAL TT-P-664 - 22-H-541. - 22-H-561 - 22-H-601 - CCC-C-428 - PPP-T-60 - MILITARY MIL-P -1 16 - MIL-B- 1 2 1 - Primer, Coating, Synthetic, Rust- Inhibiting, Lacquer-Resisting. Hose, Rubber, Steam. Hose and Hose Assembly, Rubber, Smooth Bore, Water. Hose, Rubber, Water (Yarn-Reinforced) Clot

4、h, Cotton, Duck; Fire, Water, Tape; Pressure Sensitive Adhesive, Weather and Mildew Resistant. Waterproof-for Pckaging. Preservation, Methods of. Barrier Material, Greaseproofed, Waterproofed, Flexible. Licensed by Information Handling ServicesLicensed by Information Handling ServicesMARINE CORPS 50

5、44 - U-Bar 5045 - Installation instructions for lifting fixtures, diagrammatic chart, oil fire-gas engine drive, trailer plan and elevation view. (Copies of specifications, standards, and drawings required by suppliers in connection with specific procurement functions should be obtained from the pro

6、curing activity or as directed by the contracting officer.) “2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. NATIONAL

7、BUREAU OF STANDARDS Handbook H28 Screw Thread Standards for Federal Services. (Application for copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, D. C. 20402.) UNDERWRITERS LABQRATORIESI. INC National Board of Fire Underwriters Pamphlet No. 70 (App

8、lication for copies should be addressed to the National Board of Fire Underwriters, 85 John Street, New York, New York 10038.) 3 . REQUIREMENTS “3.1 First article. As soon as practicable after award of contract or order, and prior to submission of any complete item for acceptance, the contractor sha

9、ll furnish a first article for determination of conformance to this specification. Examination and tests shall be those specified herein. Approval of the first article by the activity concerned shall not relieve the contractor of his obligation to supply steam Licensed by Information Handling Servic

10、esMIL-C-23023B (MC) cleaners conforminq to this specification. deviations of the steam cleaner from the first article shall be subject to the approval of the contracting officer. The first article,if approved, may be included in the quantity to be shipped in the final shipment. *3.2 Materials. -Mate

11、rials not specif.ied herein, or on applicable documents, shall be selected in such a manner to assure strict compliance with all requirements of tkis specification. Contact between dissimilar metals shall be avoided. Where it is necessary that dissimilar metals be assembled in intimate contact with

12、each other, posing insulating or mutually compatible material shall be used. Any changes or an inter- Dissimilar metals are defined in MS33586. *3.3 Desiqn and construction. The steam cleaner, transport mounted as specified in 3.8,shall consist of a gasoline engine, reciprocating pump, fuel system,

13、vapor uenerating system, tanks, regulators, and otb,er devices s shown n Figure 1. units shall be interchangeable and shall assemble with mating components of the unit without selection or fitting. If, during assembly of the fabricated parts of a unit, selection or fitting is required and changes in

14、 parts are necessary, no changes shall be made in these parts without prior approval of the procuring activity. H28, and the NOT-GO gaging practice shall be as specified therein, *3.3.1 Interchanaeabilitv. Component parts of assembled *3.3.2 Threads. All threads shall be in accordance with *3.3 . 3

15、Fasteninu devices. All screws, pins, bolts, and similar parts shall be installed with means for preventing loss of proper tightness and adjustment. All such parts, when subject to removal or adjustment, shall not be swaged, peened, staked, or otherwise permanently deformed. *3.3.4 Standard parts, Mi

16、litary standard parts shall be used where applicable. parts are not available, commercial hardware parts such as screws, nuts, bolts, etc., may be used provided they conform to the requirements of this specification. In the event Military standard Licensed by Information Handling ServicesMIL-C-23023

17、B Li7 m 779770b 02LihL82 b W MIL-(2-230 23B *3.3.5 Castinqs and forqinqs. All castings and forgings shall be of uniform quality, free from blow holes, porosity, hard spots, shrinkage defects, cracks, and other defects that may affect structural strength. Strength and other essential physical and che

18、mical properties of the castings and forgings shall be adequate to withstand, without damage, the performance requirements specified herein. and soldering shall be performed in accordance with best commercial practice. *3.3.6 Weldinq, brazinq and solderinq, Welding, brazing, “3.3.4 Lubrication. All

19、bearings (except sealed-for-life- type) shall be provided with means for lubrication. *3.3.8 Transport mountinq. *3.3.8:1 Trailer The trailer assembly furnished with the steam cleaner shall be inherently strong, durable, and capable of withstanding the conditions which will be met during towing over

20、 hard surface roads and in rough terrain environment. The trailer assembly, to which the steam cleaner shall be rigidly attached, shall be furnished with fenders, a tarpaulin rack, tarpaulins using cloth conforming to CCC-C-428, a hinged removable hood, and a metal tool box measuring 6 inches by 7 i

21、nches by 16 inches with hasp. A lunette and bracket assembly conforming to Drawing No. 10924561, a trailer hitch safety chain assembly conforming to Drawing No. 7328317, and a support leg conforming to Drawing No. 7343007 shall be utilized on the trailer supplier under this specification (see Figure

22、 2). *3.3.8.7.1 Liftinq fixtures. Each trailer shall have lifting fixtures conforming to Drawing Nos. 5044 and 5045 installed during production. “3.3.8.2 _ Axle _ and suspension system. The axle and suspen- sion system shallcn2st of a 1-ton capacity, torsion spring axle, installed as shown on Figure

23、 2. forming to Drawing No. 7328288.shall be used on the axle in order to obtain a track width of 50 inches, Spindles con- *3.3.8.3 Wheels. The trailer shall be equipped with riveted wheel rims conforming to Drawing No. 7387807 with hubs, less brake drums, conforming to Drawing No. 7328374. 5 License

24、d by Information Handling ServicesMIL-C-23023B (MC) *3.3.8.4 Tires and inner tubes. The trailer shall be equipped with 7:OO by 16-6 ply country tires conforming to tire inner tubes conforming to MS35392-8. nondirectional cross MS35388-9 and pneumatic *3.3.9 Gasoline ermine. The gasoline engine furni

25、shed with the steam cleaner shall be of the air-cooled, one- cylinder, 4-cycle type conforming to group I of MIL-E-11275, and shall furnish power to drive the pump, magneto, and blower fan. The engine shall be equipped with a clutch designed to operate by centrifugal forces acting on entrapped pocke

26、ts of mercury, which disengages when the engine idles (see Figure 1) . equipped with a reciprocating piston-type, positive dis- placement pump. This pump shall consist of two pistons which move with lateral motion transmitted by an eccentric crank, attached to a Vtt belt driven pully. One of the pis

27、tons shall be designed to pump water, or water and solution at a rate of 120 L6 gallons per hour (gph) against a zero lift and 85 55 gph at 16-foot lift (see 4.5.2.2). The other piston shall pump fuel to the burner assembly. (see Figure 1) . formed, scarf cut rings of asbestos impregnated with Polyt

28、etrafluoroethylene Polymer or equal. an inlet and an outlet check valve. Inlet check valves shall be identical and interchangeable and shall not require adjustment. Wearing surfaces (seat, discs, and springs) for inlet and outlet check valves shall be made of corrosion resistant materials. *3.3.10 R

29、eciprocatinq pump. The steam cleaner shall be “3.3.11 Pump packina. Pump packing shall be mandril “3.3.12 Pump check valves. Each pump body shall have “3.3.13 Iqnition system. The ignition system shall be designed to ignite the fuel under all conditions of operation. All wiring and controls for the

30、ignition system shall be weatherproofed in accordance with Pamphlet No. 70, National Board of Underwriters. of the engine, and driven by a lV1t De1.t pulley attached to the engine, shall furnish a spark to the electrode at the burner assembly of sufficient magnitude to maintain continuous fuel ignit

31、ion (see Figure i) . “3.3.14 Maqneto. A magneto, preferably external to that 6 Licensed by Information Handling ServicesMIL-C-23023B 47 W 7797706 0246184 T MIL-C-23023B (MC) *3.3.15 Vapor qeneration fuel system. The vapor generation fuel system shall perform as follows: fuel shall flow from the fuel

32、 tank through lines to the pump and metering valve and then through fuel lines and a fuel cushion hose,.designed to absorb-pump pulsations, to a pressure-atomizing burner. In an updraft combustion chamber, the atomized fuel shall mix with forced air from the motor-driven blower fan and be ignited by

33、 the electric spark. The fuel system shall be capable of burning either kerosene or fuel oils from 30 to 38 American Petroleum Institute gravity (see Figure 1) . *3.3.15.1 Vapor qeneration fuel tank. The fuel tank shall have a capacity capable of sustaining a minimum of 3 hours continuous operation,

34、 under maximum heat load. An outlet to provide a sump for the collection of water, sludge, etc. shall be installed 2 inches above the bottom of the,tank. outlet side. The tank shall be sealed to prevent possible seepage or splashing of other liquids that might contaminate the fuel in the tank. A fue

35、l strainer shall be located on the *3.3.15.2 Fuel-metering and by-pass orifice. Since it is probable that the capacity of the fuel pump will be approximately 10 times that of the burner tip, fuel must be by-passed at all times. This shall be accomplished as follows: as fuel leaves the fuel check val

36、ve, it shall be divided into two streams, one of which shall pass through an anti-siphon check valve and a fuel metering valve (see 3.15.3) . The other stream shall pass through a fuel-by-pass orifice elbow, back to the fuel tank (see Figure 1) . which allows positive control of the heating coil, sh

37、all be calibrated proportionately from zero to 7, with 7 being the maximum setting. Fuel flow through this valve shall be adjustable from zero to approximately 4 gph. “3.3.15.3 Fuel meterinq valve. The fuel metering valve, “3.3.16 Vapor qeneratinq system. Water and cleaning solution shall pass throu

38、gh the cleaner in the following manner: water shall enter the cleaner from an external source and pass through piping to a water system supply (see 3.3.17.1) selector valve. The system shall be so designed that water or water and cleaning solution may be Licensed by Information Handling ServicesMIL-

39、C-23023B LI7 7777906 024bL5 L m MIL-C-23023B (MC) drawn into the water pump. The rate of flow of cleaning solution shall be controlled by a metering valve with a range of O to 12 gph. From the pump, water or water solution shall be pumped through a water alleviator hose, .designed to absorb pump pul

40、sations, past a drain and relief valve, and into the vapor generator, where it is brought to the required temperature and pressure. system shall be capable of withstanding a static pressure of 225 pounds per square inch gage (psig), which is one and one-half times the maximum working pressure of 150

41、 psig (see Figure 1) . a progressive type heater of the continuous tubular coil type, fabricated to withstand 1,000 pounds per square inch (psi) hydrostatic test, and shall contain no drums or extended pressure chambers. Provisions shall be made in the design of the cleaner to allow for deliming of

42、the coil or for its replacement if necessary (see Figure 1). The “3.3.16.1 Vapor qenerator. The vapor generator shall have 33.3.16.2 Coil drain and relief valve. A drain and relief _ valve shall be located at the inlet side of the coil. This valve shall be designed to drain the coil when opened manu

43、ally, and if in operation excessive pressure builds up in the system, to open and allow water or water and cleaning solution to escape (see Figure 1) . “3.3.16.3 Pressure control device. A pressure control device designed to function as described below shall be installed in line with the outlet side

44、 of the heating coil. A plunger on the device shall be designed to actuate when the pressure in the system reaches 150 psi. When this plunger is actuated, it shall operate a throttling device on the gasoline engine, idling the engine. When the engine idles, the mercury clutch shall disengage, stoppi

45、ng the reciprocating pump (see Figure 1, 3.3.9, and 4.5.6) . from O to 200 psi, shall be furnished and connected to the outlet side of the heating coil. Numerical readings shall be given at O, 50, 100, 150 and 200 pounds with marks for every 10 psi. The gage shall be properly dampened against vibrat

46、ion or fluctuation and shall accurately indicate the working pressure. The gage shall be of such quality as to be durable and dependable in service under continuous pulsating pressure conditions. “3.3-16.4 Pressure qaqe. A dial type pressure gage, reading 8 Licensed by Information Handling ServicesM

47、IL-C-23023B 97 W 777770b 029blAb 3 W MIL-C-23023B (MC) *3.3.16.5 Cleaninq solution tank. The cleaning solution tank shall have a capacity capable of sustaining. a minimum of 4 hours of continuous operation at 22 to 25 percent of the full volume range of the cleaning solution metering valve. “3.3.16.

48、6 Cleaninq solution meterinq valve. The cleaner shall be equipped with a metering valve which will introduce a certain part of concentrated compound solution into the water lines. The metering valve shall be adjustable in capacity for a minimum range of zero to 12 gph at any selected ratio of concen

49、trated compound to water. When adjusted to the desired metering rate, the valve shall maintain a constant delivery to within 25 percent at any and all tank level conditions. *3.3.17 Water supply system. The cleaner shall be equipped to secure water from the following sources: (a) Tap pressure system from a minimum pressure range of 25 psi to 125 psi. (b) Suction line or vacuum pickup from well, stream, lake, or other outside source of water. 513.3.17.1 Water supply selector valve. The steam cleaner shall be supplied with a two-position selector valve between the water inlet con