NAVY MIL-C-23024 A (4)-1978 CARTRIDGE DELAY MARK 36 MOD 0《36 MOD 0标志延时炸弹》.pdf

1、MIL-C-23 024A(AS) AMENDMENT 4 20 .!-larch 1978 SUPERSEDING AMENDMENT 3 31 JANUARY 1977 MILITARY SPECIFICATION CARTRIDGE, DELAY, MARK 36 MOD O This amendment forms a part of Military Specification MIL-C-23024A dated 1 O April 1967. PAGE 2 * listed thereunder, Above STANDARDS: Delete “Bureau of Naval

2、Weapons and the document * Under DRAWINGS: Delete “Bureau of Naval Weapons“ and substitute “Naval Air Systems Command (Code Ident 30003)tt. Add, “LD 2838183 2838190 838AS100 Test Set, for Cartridge Delay, Assembly (.38 CAL Size) Sleeve Propellant, Double Base“ Under PUBLICATIONS: Delete “BUSANDA Ins

3、truction 4030.17“ and title. * Command“. Delete “Bureau of Naval Weapons“ and substitute “Naval Sea Systems PAGE 3 2.2, under CODE OF FEDERAL REGULATIONS,j,delete !49 CFR 71-78! and title, and substitute: “49 CFR 171-178 Transportation, Explosives and other Dangerous Articles“ * 3. 2, line 3 : Delet

4、e “Bureau of Naval Weapons“. JHLS DOCUMENT CONTAINSIP AGES mJ J . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I flIL-C-23024A (4) 13 m 7777906 0302786 7 m .I MIL-C-23024A(AS) AMENDMENT 4 i- PAGE 4 * 3.5, 3.6, .3.7, 3.7.1: Delete “Bureau of Naval

5、Weapons“. * 31 7, line 3 : Delete, “0s 9862“ and substitute “Drawing 838AS100f1. PAGE 5 * 3.9.2: Delete “Level and duration of pressure“ and substitute * 3.9. 2.1, line 2: Delete “1000“ and subs.titute 1;2330. * 3.9. 2.2: Delete in its entire and substitute “3.9.2.2 Time to 1600 psi. Time to 1600 ps

6、i shall not exceed 4.1 ms TU. It * Add the following: pressure shall be Tu 8.4 ms. l3.9.2.3 Time to maximum pressure, The upper limit ta maximum PAGE 6 4.3.3, line 1: Delete “111“ and substitute “91“. PAGE 7 4.6.1, delete and substitute: “4.6.1 Packaging, packing and marking. (M105) Quality-conforma

7、nce inspection shall be conducted;in accordance with the inspection criteria on the applicable drawings referenced in Section 5. PAGE 8 *. fl * 4.8.1, delete and substitute: “4.8.1 The number of cartridges selected from each production lot for the ballistic tests shall be in accordance with the requ

8、irements of Table I of MIL-STD-105, Inspection Level III. The sample of cartridges shall be divided, as nearly as possible, into three equal groups; if the sample of cartridges is not equally divisible by 3, the excess cartridges shall be placed in the group Page 2 of 4 Provided by IHSNot for Resale

9、No reproduction or networking permitted without license from IHS-,-,-flIL-C-2302LlA (4) 13 7977706 0302987 O MIL-C-23024A(AS) AMENDMENT 4 that is to be fired at -65“ F. Samples in group 1 inserted in sleeve (Drawing 2838190) of test set (Drawing DL 2838183) shall be conditioned at -65“ f 5“ F for a

10、minimum of 24 hours and fired in the test set within three minutes after removal from conditioning. Samples in group 2 inserted in sleeve (Drawing 2838190) of test set (Drawing DL 2838183) shall be conditioned at 160“ f 5“ F for a minimum of 24 hours and fired in the test set within three minutes af

11、ter removal from con- ditioning. Samples in group 3 inserted in sleeve (Drawing 2838190) of test set (Drawing DL 2838183) shall be conditioned at 70“ f 5“ F for a minimum of 24 hours and fired in the test set within three minutes after removal from con- ditioning. In addition to the sample of cartri

12、dges for the above test, 10 addi- tional cartridges shall be furnished from the production lot for investigative purposes. l1 * 1600 psi, time to maximum pressure, and lower limit of maximum pressure shall meet the requirements of 3.9. 4.8.1.1, delete first sentence and substitute: “The delay time,

13、time to PAGE 9 5.1.3, last line, delete “49 CFR 71-7811 and substitute “49 CFR 171-17811. 5.2.3, last line, delete “49 CFR 71-78“ and substitute “49 CFR 171-17811. 5.3,1, last line, delete “49 CFR 71-78! and substitute “49 CFR 171-178!. 5.3.2, delete and substitute: “5.3.2 Normal markings. Unless ot

14、herwise specified in the contract or order, the marking information on unit packages and shipping containers shall be as specified on the drawings listed on LD 537902 and LD 537903, respectively. The specified marking information shall be applied to the containers in accor- dance with the applicable

15、 provisions of MIL-STD-129. t PAGE 10 2- 6.3.1, delete and substitute: “6.3.1 Test report, The contract or order should specify that results of ballistic tests are to be forwarded to the Naval Air Systems Command (AIR- 5323G) and the procuring activity. ! Page 3 of 4 Provided by IHSNot for ResaleNo

16、reproduction or networking permitted without license from IHS-,-,-MIL-C-23024A (4) 13 999990b 0302988 2 MIL-C-230 24A(AS) AMENDMENT 4 ., . 1 6.4, delete and substitute: 116.4 Definitions. For the purposes of this specification, the following definitions apply. PAGES 11, 12, 13 and 14 6.6 and subpara

17、graphs, delete and substitute: “6.5 Explosives safety precautions. Safety precautions for explosive- loaded items are contained in DOD 4145.26M, llDOD Contractors Safety Manual for Ammunition, Explosives and Related Dangerous Material“. lt NOTE: The margins of this amendment are marked with an aster

18、isk to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate th

19、e requirements of this document based on the entire con- tent irrespective of the marginal notations and relationship to the last previous amendment. ) Preparing Activity Project No. 1377-N647 NAVY - AS *US. GOVERNMENT PRINTING OFFICE: 1978-703-12213041 Page 4 of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-