NAVY MIL-C-60805 (3)-1987 CARTRIDGE IMPULSE M150 ASSEMBLY《M150型炮筒推动装置》.pdf

1、s -77-/9 MIL-C-60805 (3) 13 = 9779706 0341085 1 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commanding Officer, Naval Ordnance Station, MIL-C-60805( OS) AMENDMENT 3 30 Jul 1987 * AMENDMENT 2

2、 15 May 1975 MI L I TARY SPEC I F I CAT I ON CARTRIDGE, IMPULSE, M150 ASSEMBLY This amendment forms a part of Military Specification MIL-C-60805(MU), dated 15 October 1968, and is approved for use within the Naval Sea Systems Comnand, Department of the Navy, and is available for use by all Departmen

3、ts and Agencies of the Department of Defense. PAGE 1 * 2.1 Delete: “MIL-E-5272 . , .I in its entirety. Delete: “MIL-C-60539 . . .I1 in its entirety. Delete: “MIL-STD-639 . . .II in its entirety. Add : Add: “MIL-A-8625 Anodic Coatings, for Aluminum and Aluminum Al 1 oys“ . “MIL-STD-810 Envi ronmental

4、 Test Methods and Engineering Guide1 ines“. PAGE 2 * 2.2 Delete in its entirety and substitute: Add: “2.2 Other publications. The following document fotms a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the document which are DOD adopted shall b

5、e those listed in the issue of the DODISS specified in the solicitation. specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the sol ici tation. Unless otherwise ANSI B46.1 Surface Texture (Surface Roughness, W

6、aviness and Lay) (Application for copies should be addressed to the American National Standards Institute (ANSI) , 1430 Broadway, NY 10018) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-bo805 (3) 13 779770b 0341086 3 (Nongovernment standards

7、and other pub1 ications are normally zwailbla These .rom the organization which prepare or which distribute the documents. documents also may be available in or through libraries or other infsrinatiwl services.)“ PAGE 2 Under “Drawings“ add: IC9223373 - Carton Al ternative, Packing Ammuni tion“. * 3

8、.2 Delete II. . . MIL-C-60539“ and substitute II. . . MIL-A-8625“. * 3.3 Delete I. . in MIL-E-5272, Procedure X11 . . .I and substitu4e: , . MIL-STD-810, Method 514.3, Test Procedure I. Test Condition I - 3.2.5 II II *.a PAGE 3 3.5 At end of sentence add the following: “drawings, referenced specific

9、ations and the fol 1 ow-! ng : II. 4.1, line 1: Delete the word “contraer“ and substitute “contract“. PAGE 4 4.2.1, delete Table II in its entirety. PAGE 5 4.3.1.2 “Size of Lot“, delete first sentence and substitute “An ammunitison lot shall consist of an identifiable group of metal parts assembltes

10、 consisting of:“. .II * 4.3.2 Delete l. , ASA B46.1 . . .It and substitute II. . ANSI 696.1 . . . PAGE 8 4.3.2.5 Delete the following: 204. “(or body)“ 205, 209, 211, 213, and 216 in their entirety. PAGE 12 MI L-C-60805( OS) AMENDMENT 3 Add: “4.3.2.11 (Carton, Alternative Packing Ammunition, Dwg. C9

11、223373). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-bo805 (3) 13 W 7779706 O343087 5 m- i MIL-C-60805( OS) AMENDMENT 3 CRITICAL None defined MAJOR None defined MINOR 201. Contents loose 202. Box broken or damaged 203. Number of units con

12、tained incorrect 204. 205. Tape incorrect Marking mi ssi ng , incorrect or i 11 egi bl e Manual Vi sual Vi sual Vi sual Vi sual I PAGE 13 * 4.3.3.5.1: Delete and substitute: “4.3.3.5.1 Ballistics. Twenty one assembled cartridges from each production lot shall be tested to determine compliance with r

13、equirement of 3.4.1 and 3.4.2. The unit shall be temperature conditioned as provided in Table VI and 4.4.4.1. Failure of any cartridge to comply with the requirements of 3.4.1 and 3.4.2 shall be cause for rejection of the lot.“ * 4.4.1 Delete II. . . MIL-C-60539 . . .II and substitute I. . . MIL-A-8

14、625. * 4.4.2 Delete I. . . MIL-E-5272, Procedure XII“ and substitute I. . . MIL-STD-810, Method 514.3, Test Procedure I, Test Condition 1-3.2.5“ PAGE 14 * 4.4.4 Delete column 2 (AQL) in its entirety, change sample size from “7“ to lllol. The margins of this amendment are marked with an asterisk to i

15、ndicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only and the Government assumes no 1 iabil i ty whatsoever for any inaccuracies in these notations. contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue, Bidders and Preparing Activity: Project No. 1377-N889 Navy - OS 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-