NAVY MIL-C-82141 B-1995 COVER MUSIC CARRYING POUCH EMBROIDERED《刺绣运输袋盖子》.pdf

1、INCH-POUND I MIL-C-82 14 1B (MC) SUPERSEDING MIL-C-8214l.A( MC) - I- 20 February 1990 MILITARY SPECIFICATION COVER, MUSIC CARRYING POUCH: EMBROIDERED This specification is approved for use by U.S. Marine Corps, Department of the Navy, and is available for use by all Departments and Agencies of the D

2、epartment of Defense. 1. SCOPE 1.1 Scope. This specification covers requirements for one type and size scarlet wool broadcloth music carrying pouch cover, embroidered with the United States Marine Corps emblem. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and ha

3、ndbooks. The following specifications, standards and handbooks form a part of this specification to the extent .specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) a

4、nd supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to the Commander (PSE-C), Marine Corps Systems Command, Quantico, VA 22134-5010 by using t

5、he self addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 7720 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted

6、without license from IHS-,-,- MIL-C-82141B m 9999906 1997875 245 m MIL-C-8214 1B( MC) SPECIFICATIONS FEDERAL A-A-52 O 9 4 Vu-P-268 MILITARY MIL-G-16491 MIL-B-17757 MIL-C-29405 STANDARDS FEDERAL FED-STD-191 FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 Thread, Cotton Paper, Kraft, Wrapping Gromet, Met

7、allic Box, Shipping, Fiberboard (Modular Sizes) Cloth, Broadcloth, Wool and Wool/Nylon Textile Test Methods Stitches, Seams, and Stitchings Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage 2.1.2 Other Government documents and Publications. The following ot

8、her Government documents and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. 2.2 Non-Government Publications. The following documents(s) form a part of this document to the extent specified herein.

9、Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2).

10、DEPARTmNT OF DEFENSE STANDARD SHADES FOR HERALDIC YARNS DEPARTMENT OF DEFENSE STANDARD COLOR CARD OF OFFICIAL STANDARDIZED SHADES FOR SEWING THREADS (Application for copies should be addressed to the Color Association of the United States, Inc., 343 Lexington Ave., New York, NY 10016.) 2 Provided by

11、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. AMERICAN SOCIETY OF TESTING MATERIALS ASTM D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to American Society for Testing and Materials, 1916 Race Street, Philade

12、lphia, PA 19103.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of Drecedence. In the event of a confli

13、ct between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption had been obtained. (Unless otherwise indicated, copies of federal and milit

14、ary specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 3. REQUIREMENTS 3.1 Guide samDles. Guide samples are furnished solely for guidance and information to the contractor (see 6.4). Var

15、iation from this specification may appear in the standard sample, in which case the specification shall govern. 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection and approval (see 4.4 and 6.3). 3.3 Materials 3.3.1 Basic mater

16、ial. The basic material shall be cloth, broadcloth, wool, scarlet, shade 2501, 14-15.5 ounce, conformingto type I of MIL-C-29405 except the finished cloth shall show fair fastness to crocking, perspiration, wet (dry) cleaning and light. 3.3.2 Buckram. The buckram for embroidery backing shall be of g

17、ood commercial quality, as used in the industry. 3.3.3 Ravon thread. The embroidery thread shall be continuous filament, regenerated cellulose (viscose or cuprmonium) type of rayon, 600 2 30 denier, single ply, and minimum breaking strength of 2.3 pounds. 3 Provided by IHSNot for ResaleNo reproducti

18、on or networking permitted without license from IHS-,-,-. 3.3.3.1 Color and colorfastness. Embroidery thread shall match the approved standard shades (see 6.4), conforming to the following cable numbers for rayon thread (see DoD Standard Shades for Heraldic yarns ) : White Scarlet, HL Silver Gray, H

19、AM Light Blue, HU Old Gold, HE Cable No. 67101 Cable No. 67111 Cable No. 67137 Cable No. 67120 Cable No. 67105 The dyed threads shall show good fastness ,o wet (dry) cleaning and light when tested as specified in Table II. 3.3.4 Cotton thread. 3.3.4.1 Bobbin thread. Bobbin thread used in the embroid

20、ery shall be a good commercial grade of two-ply cotton yarn. 3.3.4.2 Sewins thread. The thread for seaming and stitching shall be cotton, soft finish, ticket No. 40, 3-ply, conforming to type I of A-A-52094. The color of the thread shall be scarlet cable No. 66040, except when dyed thread shall show

21、 fair fastness to wet (dry) cleaning and light when tested as specified in A-A-52094. The thread for basting shall be a good commercial grade. 3.3.5 Evelet. Eyelet shall be brass, bright finish, conforming to type III, class 1, size O of MIL-G-16491. 3.4 Desian. The cover shall be the United States

22、Marine Corps design, as shown on Figures 1 and 2. 3.5 Patterns. The standard patterns furnished by the Government shall not be altered in any manner and shall be used only as a guide for cutting working patterns. The standard patterns provide for a 1/4 inch seam allowance. 3.5.1 List of pattern part

23、s. Covers shall be cut from the specified material in accordance with the pattern parts indicated: Item Pattern nomenclature No. of cut parts Material: Cloth, broadcloth, wool 1. Front part 2. Lower backpart 3. Upper backpart 1 1 1 4 Provided by IHSNot for ResaleNo reproduction or networking permitt

24、ed without license from IHS-,-,-MIL-C-82141B(MC) 3.6 Construction. The construction shall conform in all respects to Figure 2 and as specified herein. The cover, consisting of three pieces of basic material, shall have a one piece front embroidered with the United States Marine Corps emblem, a two p

25、iece back with a horizontal, straight type buttonhole in the lower backpart, and a brass eyelet near the top end of the cover. All raw edges, including edges of seams, shall be overedge stitched. 3.6.1 Manufacturinff requirements. The cover shall be manufactured in strict accordance with the operati

26、ons and the stitch, seam and stitching types specified in Table I. 3.6.1.1 Operations. The contractor is not required to follow the exact sequence of operations as listed in Table I, but all operations specified shall be used to manufacture the cover. 3.6.1.2 Stitches, seams and stitchinqs. The stit

27、ch, seam and stitching types specified in Table I shall conform to FED-STD-751. The number of stitches per inch as specified in Table I indicates the minimum and maximum number permitted. 3.6.1.3 Tackina and backstitchinq. Ends of seams or stitching, when not caught in other seams or stitching, shal

28、l be securely backtacked not less than 1/4 inch; thread breaks shall be secured by stitching back of break not less than 1/2 inch. All thread ends shall be trimmed and loose ends shall be removed. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NO

29、MIL-C-82L4LB = 9999906 1997879 990 H TABLE I MANUFAi OPERATI ON Cuttinq. a. Cut covers in strict accordance with patterns furnished by the Government. b. Cut fabric in direction indicated by directional lines on pattern. ReDlacement of damaaed parts. a. Replace at time of cutting the component part(

30、s) containing damages such as holes or serious weakening defects, such aE smashes, multiple floats and slubs likely to develop into holes. b. Replace component part damaged during the manufacturing process by needle chews which may be expected to develop into o hole, scissors or knife ruts, tears, m

31、ends or burns. Xake front part of cover. 3. The U. S. Marine Corps Sa-2 i) rs STCH/ IN L8-22 NDL 10/3 BOB/ - LPR 40/3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9 io TABLE I MANFAC OPERATION Attach evelet. a. The eyelet shall be securely clinche

32、d to the cover through front and upper backpart without cutting or otherwise damaging the fabric, at location shown by the mark on the pattern. The flange of the eyelet shall be on the front of the finished cover. Clean cover. a. Pull any basting thread, trim and remove any loose ends of thread and

33、remove any spots or stains. Press cover. a. Press the cover smooth and flat with a heated pressing machine. URING I; STCH TYPE QUIREME SEAM/ STCH TYPE TS STCH/ IN NDL 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-82iI4iIB = 999990b 1997883

34、3iIL MIL-C-82141B(MC) 3.7 Finished measurements. The finished cover shall conform to that shown in Figure 2. 3.8 Workmanship. The finished cover shall conform to the quality and grade of product established by this specification. The occurrence of defects shall not exceed the applicable acceptable q

35、uality levels (AQLs). 4. QUALITY ASSURANCE PROVISIONS 4.1 ResPonsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract o

36、r purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such i

37、nspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 ResPonsibilitv for corndiance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection

38、system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality con

39、formance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.2 Classification of inspection. The inspection requirements specified herein are classified as follows: 1. 2. First article inspection (se

40、e 4.4). Quality conformance inspection (see 4.5). 4.3 Inspection conditions. Unless otherwise specified, all inspections shall be performed in accordance with the test conditions specified in MIL-STD-105. 4.4 First article insPection. When a first article is required (see 3.2 and 6.3), it shall be e

41、xamined for the defects specified in 4.5.2.1 and 4.5.2.2. The presence of any defect may be cause for rejection of the first article. The number of units to be inspected shall be specified by the contracting officer. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

42、ense from IHS-,-,-HIL-C-ZIILB M 999990b L777884 258 MIL-C-82141B (MC) 4.5 Quality conformance inspection. 4.5.1 Component and material testinq. In accordance with 4.1, components and materials shall be inspected and tested in accordance with all the requirements of referenced specifications, drawing

43、s, and standards, unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase documents. The method of testing shall be as specified in FED-STD-191, wherever applicable. Testing shall be performed on components listed in Table II for characteristics noted.

44、 All test reports shall contain the individual values used in expressing the final result. The lot shall be unacceptable if one or more sample units fail to meet any of the test requirements specified. The lot size and sample size shall be in accordance with the following: Component Lot size express

45、ed as Sample unit for testinq Rayon thread Bobbins Sufficient number of bobbins to total a minimum of 360 yards The sample size shall be as shown below. The lot shall be unacceptable if one or more units of product fail to meet any specified requirements. Lot Size 800 or less 801to 22,000 22,001 and

46、 over Sample Size 2 3 5 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ta a O d ci $ ci m al I3 I H H W 4 I3 4 rl O y rl m rl O (v O 1 ta -4 O 4 3 e m m m m m m m m m c pi CI rl loose, exposing teeth of washer. Not horizontal straight type. Numbe

47、r of stitches less than specified. Stitching not securely caught in fabric causing stitching to pull away. Not securely tacked at each end. Broken stitch. Length not within specified cange. Not in conformance with standard sample with respect to design, :olor arrangement, stitch type Dr density. 3mb

48、roidery work stif f. 107 108 109 110 111 112 113 L14 115 116 205 206 207 108 !O9 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-82L4LB D 9999906 L997B88 9T3 W Classification Defects Major Examine Minor Embroidery (cont d) Assembly Cleanness

49、 Thread colors not as specified. Shift affecting appearance. Loose or tight tension affecting appearance. Bunched or tangled yarns. Stitching incomplete. Broken or skipped stitches affecting appearance. Bobbin thread showing on face of embroidery affecting appearance. Embroidery misshaped or distorted. Buckram omitted or entire design not reinforced by buckram. Edges of cover