NAVY MIL-C-82665-1977 CARBON BLACK《炭黑》.pdf

1、MI L-C-82665 (OS ) 3t January i977 MI t ITARY SPEC1 FI CATION CARBON BLACK This specification is approved for use by the Naval Sea Systems Command, Department of the Wavy and is available for use by all Departments and Agencies of the Department of Defense. 1, SCOPE 2.1 Scope. This specification cov

2、ers one type of carbon black referred ta herein as “the material“. 2, APPLICABLE IOCUMENTS 2.1 Issues of documents. The following documents of the issue in effect o.n dae of invitation for bids or request for-proposaT, form a part of this specificatian to the extent specified herein. STAXDARDS Mi 1

3、i tary MI L-STD-I 05 Sampl ing Procedures and Tab1 es for Inspection by Attributes MIL-STD,-129 Marking for Shipping and Storage (Copies of specifications, standards , drawings, and pub1 ications required by suppliers in connection with specific procurement functions should be obtained from the proc

4、uring activity or as directed by the cot-ttr-acting officer,) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. indicated, the issue in effect on the date of the invitation for bids or the request for proposal shall apply. - AMERICAN SO

5、CIETY FOR TESTING AND MATERIALS (ASTM) Unless otherwise ASTM D 1506-75 Ash Content of Carbon Black ASTM D 1509-75 Heating Loss of Carbon Black ASTM D 7512-75 pH Value of Carbon Black Beneficial comments (recommendations , addiions, deletions) and any pertinent data which may be of use in improving t

6、his document chouPd be addressed to: Commanding Officer, Naval Ordnance Station , Standardization Division (Code 611) , Indian Head, Maryland PO640 by using the self-addressed Standardization Document improvemen Proposal (DD Form 1426) appearing at the end o.f this document or by letter. Licensed by

7、 Information Handling ServicesMIL-C-82665( OS) (Application for copies should be addressed to the American Society CODE OF FEDERAL REGULATIONS for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103) 49 CFR 100-199 Transporta ti on (The Code of Federal Regulations is available from the S

8、uperintendent of Docuemnts, U. S. Government Printing Office, Washington, DC 20402. Orders should specify “49 CFR 100-199 (latest revision)“). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT (Application for copies should be addressed to American Trucking Associations, Attn: Tarriff Order Se

9、ction, 1616 P Street, Washington, DC 20036.) National Motor Freight Classification UN I FO RM CLASS I F I CAT I ON COMM I TT E E, AG EN T (Application for copies should be addressed to the Uniform Classi- Un i form Frei ght Cl assi f icati on fication Committee, Room 1106, 222 South Riverside Plaza,

10、 Chicago, IL 60606. ) (Technical society and technical association specifications and standards are generally available for reference from libraries. are distributed among technical groups and using Federal agencies.) They 3. REQUIREMENTS form. 3.1 Material. The material shall be carbon black in fin

11、e powder 3.2 Chemical and physical properties. The chemical and physical properties of the material shall be in accordance with TABLE I. TABLE I. Chemical and physical properties. CHARACTER1 ST1 C REQUIREMENTS MIN MAX Heating loss, Weight % - 1 .o ASH, Weight % Ether Extract, Weight % pH value Iodin

12、e Absorption, Volume % - o. 1 - o. 1 2. o 6. O 95 - Licensed by Information Handling Services3.3 Workmanship. The material shall be uniform, free from conta- minants, foreign material or any other defect that would prevent its use for the purpose intended. 4. QUALITY ASSURANCE PROVISIONS 4.1 Respons

13、ibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein, Except as otherwise speci- fied in the contract, the contractor may use his own or any other facilities suitable for the performan

14、ce of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure that supplies and services conform to prescribed requirem

15、ents. 4.2 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be performed under the following conditions: a. Temperature: Room ambient 18 to 35C (65 to 95F) b. Altitude: Normal ground c. Vibration: None d. Humidity: Room ambient to 95 percent relative, maximum 4.3 Sam

16、pling. 4.3.1 - Lot. Unless otherwise specified in the contract (see 6.2), a lot shall consist of all material manufactured in one continuous production run or in one batch, under essentially identical conditions, from he same raw materials, and to be offered or acceptance at one time. Several batche

17、s, manufactured from the same raw materials, may be blended to form a uniform larger batch which shall then constitute a lot for inspection purposes. 4.3.2 Sampling. Sampling for quality conformance inspection shall be in accordance with inspection level I of MIL-STD-105. unit shall be one unit pack

18、age or container of material, shall consist of sufficient material to perform the quality conformance tests as specified in 4.4. 4.4 Quality conformance inspection. Each sample obtained in accordance with 4.3.2 shall be subjected to the tests of 4.5. able quality level (AQL) shall be 2.5% defective.

19、 When specified in the contract or order (see 6.2). showing quantitative results for all quality conformance tests specified for each lot of material. The sample Each sample The accept- The contractor shall furnish test reports 4.5 Tests. 4.5.1 Heating loss. The heating loss shall be determined in a

20、ccordance with ASTM D 1509-75. 3 Licensed by Information Handling ServicesMIL-C-82665( OS) 4.5.2 Ash content. The ash content shall be determined in accordance with ASTM D 1506-75 with the following exceptions: a. The sample shall not be dried prior to weighing. b. The sample shall be ignited at 950

21、OC. c. The calculation shall be corrected so that c = weight of crucible plus the sample, g, and d = weight of crucible plus the ash, g. 4.5.3 Ether extract. The ether extract shall be d accordance with the following: termined in a. b. Weigh a sample of approximately 10 grams (9) of carbon black to

22、the nearest 0.1 mg Transfer the sample to an extraction thimble and extract with ether using a tared extraction flask and a Soxhlet extractor or equivalent. Use a hot-water bath or a steam plate as the source of heat. Adjust the applied heat so that ether drops from the reflux condenser at the rate

23、of 2 to 3 drops per second. Continue the extraction for 8 hours. Remove the extraction flask and evaporate the ether by heating on a steam bath until approximately 25 millilitres (ml) of the ether solution remains. Complete the evaporation to dryness by blowing a slow current of dry air over the sol

24、ution. Dry the flask to constant weight to the nearest 0.1 mg in a vacuum desiccator containing ACS grade sulfuric acid. c. d. e. f. Calculate the ether extractable matter as follows: wt% ether extract = (C-B) A x 100 A = weight of sample, g B = weight of flask, g C = weight of flask and residue, g

25、4.5.4 pH value. The pH value shall be determined in accordance with ASTM D 151 2-75. 4.5.5 Iodine absorption. Iodine absorption shall be determined in accordance with the following: a. Reagents: (1) Standardized iodine solution, 0.01 normal (N). (2) Standardized sodium thiosulfate solution, 0.01 N.

26、(3) Starch indicator solution, 1 percent b. Apparatlus: Platinum crucible with cover, 15 ml (type used in coal analysis: 0.1 mm diameter hole should be punched in cover). 4 Licensed by Information Handling ServicesLicensed by Information Handling ServicesMIL-C-82bb5 68 W 7779906 0323324 2 H- a. b. M

27、anufacturers name and 1 ocation c. Material trade name d. Net weight e. f, Storage conditions g. Title, number and date of this specification Lot number, batch number(s), and date of manufacture Contract or purchase order number 6. NOTES is intended for use as an ingredient in a liner and adhesive c

28、omposition for the CKU-5/A rocket catapult assembly and other rocket motor appl ications. 6.1 Intended use. Carbon black in accordance with this specification 6.2 Ordering data. Procurement documents should specify the following: 6.2.1 Procurement requirements. a. Title, number and date of this spec

29、ification b. Quantity required c. P1 ace of del ivery d. Inspection conditions when other than as specified (see 4.2). e. Lot size if other than as specified (see 4.3.1i) f. Packaging requirements if other than as specified (see 5.1) g. Size of container required (see 5.1) h. Any special markings re

30、quired (see 5.2) requ here will da ta 6.2.2 Contract data requirements. Items of deliverable data red by this specification are cited in the following paragraph n: Paragraph 4.4 Data Requirement Qual i t.y conformance - Appl i ca bl e DID* inspection data *DIDs (Data Item Description/DD Form 1664) f

31、or the above requirements be documented in the applicable ADL (Authorized Data List). Such will be delivered as identified on completed (numbered) DIDs when specified on DD Forms 1423 (Contract Data Requirements Lists) and incor- porated into appl icabl e contracts. 6.2 Suggested source of supply. A

32、 product that has met the require- ments of this specification in past procurement actions is Acetylene Black, 100% compressed, manufactured by Shawinigan Products Corporation, 111 Charlotte Place, Englewood Cliffs, NJ 07632. for the convenience of the procuring activity and is not to be construed a

33、s a waiver of any requirement of this specification nor as any limitation of additional potential sources of supply. This information is Cu s tod i an : Navy - OS Preparing Activity : Navy - OS * U. S. GOVERNMENT PRINTING OFFICE: 1977 -703-020/1904 6 Project Number: 681 0-NA37 Licensed by Information Handling Services