NAVY MIL-D-3263 B-1987 DESICCANT CONTAINERS DEHUMIDIFIER《减湿干燥器容器》.pdf

1、MIL-D-3263B 20 July 1987 SUPERSEDING MIL-D-3263A 5 August 1968 (See 6.6) MILITARY SPECIFICATION DESICCANT CONTAINERS, DEHUMIDIFIER This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers desiccant containers a

2、nd their storage cases which are suitable for the static dehumidification of small, enclosed spaces, and which can be readily reactivated. 2 APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification

3、 to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. I Beneficial comments (recommendations, additio

4、ns, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appe

5、aring at the end of this document or by letter. AMSC NIA FSC 4440 DISTRIBUTION STATEMENT A Approved for public release; distribution unlimited Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-UIL-D-3263B SPEC IF ICATIONS FEDERAL QQ-A-200/8 - Aluminum

6、Alloy 6061, Bar, Rod, Shapes, Tube and QQ-A-250/11 - Aluminum Alloy 6061, Plate and Sheet. QQ-S-698 - Steel, Sheet and Strip, Low-Carbon. VV-S-190 - Sealing Compound (Dipcoat). PPP-B-591 - Boxes, Shipping, Fiberboard, Wood-Cleated. PPP-B-601 - Boxes, Wood, Cleated-Plywood. PPP-B-621 - Boxes, Wood, N

7、ailed and Lock-Corner. PPP-B-636 - Boxes, Shipping, Fiberboard. Wire, Extruded. MILITARY DOD-D-1000 - Drawings, Engineering and Associated Lists. MIL-D-3716 - Desiccants, Activated for Dynamic Dehumidification. MIL-L-10547 - Liners, Case, and Sheet, Overwrap; Water-Vapor- proof or Waterproof, Flexib

8、le. STANDARDS MILITARY MIL-STD-129 - Marking for Shipment and Storage. DOD-STD-100 - Engineering Drawing Practices. (Copies of specifications and standards required by contractors in con- nection with specific acquisition functions should be obtained from the contracting activity or as directed by t

9、he contracting activity.) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DoDISS specified in the solicitation. Un

10、less otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) A 229 - Standard Specification for Steel Wire, Oil-Tempered for Mechanical

11、Springs. (DoD adopted) A 386 - Standard Specification for Zinc Coating (Hot-Dip) on Assembled Steel Products. B 6 - Standard Specification for Zinc (Slab Zinc). (DoD adopted) B 633 - Standard Specification for ElectrodeposAted Coatings of Zinc on Iron and Steel. (DoD adopted) (Application for copies

12、 should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in o

13、r through libraries or other informational services.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-32b3B YY 999990b 0207403 9 m MIL-b3263B 2.3 Order of precedence. In the event of a conflict between the text of this specification and the r

14、eferences cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3.

15、REQUIREMENTS 3.1 Materials. Materials used in the construction of the desiccant con- tainer and the storage case shall be free from defects, capable of being punched or formed, or both, without the creation of cracks and suitable for the purpose i nt ended . 3.1.1 Recovered materials. Unless otherwi

16、se specified herein, all material and articles incorporated in the products covered by this specifica- tion shall be new and may be fabricated using materials which have been col- lected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw mater

17、ials. None of the above shall be interpreted to mean that the use of used products is allowed under this specification unless otherwise specifically specified. 3.2 Container. The container shall consist of two circular side plates, an end band (or ring), a handle, a receptacle for an indicating cart

18、ridge, built as a single unit, ready for installation. 3.2.1 Configuration. The container shall have contours, dimensions, and c tolerances in accordance with figure 1. 3.2.2 Side plates and end band. The container side plates and end band The side (or ring) shall be made of aluminum in accordance w

19、ith QQ-A-250/11. plates shall be at least 0.032 inch thick and each plate shall be uniformly perforated. The perforated area shall be not less than 27 percent of the total effective area of each plate with the perforation having a maximum diameter of 0.033 inch. The minimum number of perforations sh

20、all be 324 per square inch. The end band (or ring) shall be at least 0.050 inch thick. The side plates and end band shall be fastened together by spot welding, brazing, or by blind rivets. 3.2.2.1 Staybolts. Three 3/8 inch staybolts shall be fastened, uniformly spaced at 120-degree intervals and app

21、roximately 2-1/2 inches from the center of the container. The staybolts shall be of aluminum in accordance with QQ-A-200/8 and shall be fastened flush against the surface of the side plates. 3.2.3 Handle. Each container shall be provided with a handle. The handle shall be constructed of aluminum in

22、accordance with QQ-A-250/11 and shall be at least 0.125 inch thick. The handle shall be provided with a hole not less than 3/4 inch in diameter for handling the desiccant container. The handle shall be securely fastened to the end band (or ring) by spot welding, brazing, or by blind rivets. 3.2.4 Re

23、ceptacle. Each container shall be provided with a receptacle located in the end band (or ring) approximately 30 degrees from the handle, 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-3263B Lill 999990b 0209YOLi O MIL-D-3263B into which a 3/

24、4-inch indicating cartridge can be screwed. shall be of aluminum in accordance with QQ-A-250/11 and shall be perforated at the bottom or provided with a screen, to retain the desiccant and permit circulation of air between the desiccant and the indicating cartridge. The receptacle shall be either de

25、ep enough to permit insertion of the cartridge flush with the end band (or ring), or shall be provided with a collar to protect the indicating cartridge. The indicating cartridge shall be in ac- cordance with figure 2, and shall be provided in the receptacle of each con- tainer (see 6.3). The recept

26、acle 3.2.5 Desiccant. Each container shall be filled with at least 5 pounds of activated desiccant conforming to grade H, type I or II of MIL-D-3716. 3.2.5.1 Indicator desiccant. The indicator cartridge shall be filled with activated desiccant conforming to grade H, type IV of MIL-D-3716. 3.3 Airtig

27、ht storage case. The storage case shall consist of a cylin- drical body with two drop-type handles, bottom panel, a cover (see 3.3.6), with a handle and four trunk-type clamps. When subjected to an internal air pressure of 2 inches of water, the pressure drop shall not exceed 0.2 inch of water in 10

28、 minutes. The case shall satisfactorily accommodate eight of the desiccant containers specified in 3.2. 3.3.1 Construction. The configuration, physical dimensions and toler- ances of the storage case shall be in accordance with figure 3. 3.3.2 Body. The body of the storage case shall be made of blac

29、k steel in accordance with QQ-S-698 and shall be at least 0.034 inch thick. shall have at least three horizontal strengthening beads. The side joints shall be lock seamed, welded or secured by blind rivets. The top edge shall be rolled over a 3/16 inch diameter steel wire to form a tightly closed he

30、ad. The body 3.3.3 Bottom panel. The bottom panel shall be flat and formed in one piece from black steel in accordance with QQ-S-698. The panel shall be at least 0.045 inch thick, and shall be joined to the body by a double seam or seam weld. 3.3.4 Handles. The storage case shall be provided with tw

31、o identical drop-type handles. The handles shall be made of black steel wire in accordance with ASTM A 229. The wire shall be at least 5/16 inch in diameter. The handles shall be attached to the body by means of handle clips formed from black steel in accordance with QQ-S-698. The clips shall be at

32、least 0.045 inch thick and shall be located over the side seams (see figure 31, diametrical- ly opposite each other. The clips shall be securely fastened to the body with at least four spot welds. The clips shall be provided with stops so the handle cannot be elevated through an angle greater than 8

33、0 degrees. 3.3.5 Clamps. Each storage case shall be provided with four trunk-type clamps uniformly spaced around the top edge of the body and 45 degrees from the drop handles. The clamps shall consist of a bracket to which shall be riveted a handle fitted with a steel wire claw. The bracket and hand

34、le shall be made of black steel in accordar,c.e with QQ-S-698 and shall be at least 0.045 inch thick. The claw shall be made of steel wire in accordance with ASTM A 229 and shall be at least 0.135 inch in diameter. The bracket shall fit tightly 4 Provided by IHSNot for ResaleNo reproduction or netwo

35、rking permitted without license from IHS-,-,-MIL-D-32b38 Y4 m 99999013 0209i405 2 .= Hl L-D-3263B against the top bead and shall be securely fastened to the body by at least two spot welds or by at least two blind rivets. hole approximately 1/8 inch in diameter to receive a sealing wire (see figure

36、3). Each clamp shall be provided with a 3.3.6 Cover. Each storage case shall be provided with a snug fit cover. The cover shall be made of black steel in accordance with QQ-S-698 and shall be at least 0.045 inch thick. The cover shall be single piece construction, with the cover edges formed into a

37、semicircular flange to fit tightly over the beaded edge of the body. the body. The cover shall be concave and recessed at least 1/2 inch into 3.3.6.1 Cover handle. A folding type handle shall be provided on the top side of the cover and shall not interfere with stowing sealed cases one on top of eac

38、h other. The handle shall not project beyond the top edges of the semi- circular flange. ASTM A 229 and shall be attached to the center of the cover by a steel clip. The wire shall be at least 5/16 inch in diameter. The clip shall be at least 0.045 inch thick. least four spot welds or by four blind

39、rivets. The handle shall be made of steel wire in accordance with The clip shall be securely fastened to the cover with at 3.3.7 Finish. After fabrication, the storage case, including the support brackets of the clamps and the handle clip, shall be coated both inside and out with zinc by the hot-dip

40、 process, or electroplated. The handle and wire spring to the clamps shall be electroplated with zinc. shall be in accordance with ASTM A 386 with the spelter conforming to ASTM B 6. The electroplated zinc coating shall conform to ASTM B 633. The hot-dipped zinc coating 3.4 Identification plate. Eac

41、h desiccant container and each storage case shall be provided with a single identification plate. be Gothic capitals for letters, and numerals, and other characters shall be of similar appearance. be as necessary for easy readability except for the storage instructions on the storage case cover whic

42、h shall be as specified in 3.4.3. the desiccant container shall be stamped or embossed into the handle of the container. into the cover of the storage case. be filled with black enamel to insure legibility. The type of marking shall The size of the letters, numerals and other characters shall The da

43、ta applicable to The data applicable to the storage case shall be stamped or embossed The markings on the storage case cover shall 3.4.1 Identification plate information. The identification plate shall contain the following information: (a) Item name. (b) Federal stock number. (c) Weight (see 3.4.1.

44、1), as applicable. (d) Contract number. (e) Manufacturers name and address. 3.4.1.1 Weight information. Each completed desiccant container shall be weighed with the desiccant in the reactivated condition and the gross weight to the nearest tenth of a pound shall be added to the identification plate.

45、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-3263B 3.4.2 Instructions (desiccant container only). The instructions for reacti- vation of the desiccant shall be as shown on figure 1. 3.4.3 Instructions (storage container only). The storage i

46、nstructions shall be as shown on figure 3. in height. Instruction markings shall be at least 1/2 inch 3.5 Drawings. Drawings delineating the equipment shall be furnished in accordance with DOD-D-1000 and DOD-STD-100. 3.6 Workmanship. Desiccant containers and storage cases shall be free from defects

47、that effect their appearance or operation. The container end band and the storage case body and cover shall show no cracks due to forming. Sharp edges, burrs and imperfections shall be removed from all parts subject to contact with personnel. The hot-dipped coatings shall be smooth, free from uncoat

48、ed spots, injurious lumps, blisters and dross or flux. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the con- tract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as ot

49、herwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all re