NAVY MIL-D-60568 B-1992 DELAY ELEMENT CARTRIDGE M13 ASSEMBLY《M13型炮筒延迟发射装置》.pdf

1、T MIL-D-605bB 13 m 9799906 O509097 9 I INCH-POUND I MIL-D-60568B 15 January 1992 SUPERSEDING 18 April 1967 MIL-D-60568A MILITARY SPECIFICATION DELAY ELEMENT, CARTRIDGE, M13 ASSEMBLY mis speccation is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. T

2、his specification covers the requirements for the M13 Cartridge Delay Element (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise spec

3、ified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplements thereto, cited in the solicitation (see 6.2). SPECIFICATIONS MILITARY MIL-B-550 Barium Chromate MIL-A-2550 Ammunition, General Specification

4、for Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Standardization Branch (Code 3730), 101 Strauss Avenue, Indian Head, MD 20640-5

5、035, by using the self addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networ

6、king permitted without license from IHS-,-,-NIL-D-bO5bB 13 m 999990b 0509100 L m- e d MIL-D-60568B MIL-B-51092 Baron, Amorphous, Powder MIL-C-60539 Coating, Anodic, Conventional for Aluminum and Aluminum Alloy STANDARDS MILITARY MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes

7、 MIL-STD-109 Quality Assurance Terms and Definitions MIL-STD-453 Inspection, Radiographic MIL-STD-810 Environmental Test Methods and Engineering Guidelines (unless otherwise specified, copies of federal and military specifications and standards are available from Standardization Documents Order Desk

8、, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19 1 1 1-5094.) 2.1.2 Other Government documents, drawings, and publications. The following Government drawings form a part of this specification to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicita

9、tion (see 6.2). DRAWINGS NAVAL ORDNANCE STATION (CAGE Codes 19200 and 19203) DL85961 13 8826728 8826729 Delay Element, Cartridge, M13 Assembly Ammunition, Container, Metal, M21 for Delay Element, M5 or M8 Box, Packing, Ammunition, for Delay Element M5 or M8 in Metal Container M2 1 (Application for c

10、opies should be addressed to: Commanding Officer, Naval Ordnance Station, Data Control Branch (Code 3720), Indian Head, MD 20640-5035.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. N

11、othing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a first article sample shall be subjected to first article inspection (see 4.4, 6.2 and 6.3

12、). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e MIL-D-605686 13 II 9399906 0509l101 3 MIL-D-60568B 3.2 Conformance to documents. The M13 delay element covered by this specification shall be manufactured in accordance with DL85961 13 and all do

13、cuments listed thereon. 3.3 Materials. All materials used in the manufacture of the cartridges shall conform strictly to the specifications referred to on the respective drawings unless specific approval in writing covering a departure therefrom has been obtained from the cognizant Navy design activ

14、ity prior to manufacture. When alternate materials or methods of manufacture are specified on th9 drawings, the bidders selections shall be clearly stated in the proposal. 3.4 Components. 3.4.1 Primary components. For the purpose of this specification, the M42 Primer, Delay Charge and the output mat

15、erial charge are considered primary components. Only primary components from a single lot shall be used in a production lot of cartridges; however, one primary component production lot may be used in more than one cartridge production lot (see 6.6). 3.4.1.1 Primer. The primer shall conform to the ap

16、plicable drawing and reference specification. Only percussion primers from lots manufactured within the last 24 months or recertified within the last 12 months shall be used in these units. Prior to assembly into a delay element, the primer shall be visually examined in accordance with 4.6.5 and rad

17、iographically examined for defects as specified in 4.7.1. 3.4.2 Protective finish. The finish of each component part shall be in accordance with MIL-C-60539 0 and the applicable drawing (see 4.7.2). 3.5 Assembly. 3.5.1 Radiographic examination. Each delay element assembly shall be radiographically e

18、xamined for defects (see 4.7.3). 3.5.2 Vibration. The assembled delay element shall withstand vibration as prescribed in MIL-STD- 810, Method 514.3, Test Procedure I, Test Condition 1-3.2.5 without evidence of any disintegration of the primer, propellant, or igniter, or derangement of any component

19、(see 4.7.4 and 6.2). 3.6 Functional requirements. 3.6.1 Delay element performance. 3.6.1.1 Misfires. The ignition delay element shall not fail to fire. 3.6.1.2 Ballistics. The ignition delay charge shall consist of barium chromate, as specified in MIL-B- 550, and boron, as specified in MIL-B-51092,

20、in the proportion and quantity fixed by the contractor to produce the ignition delay times required in table I (see 6.5.1). 3.7 Workmanship, Delay elements shall be free of cracks, splits, or other defects which might prevent proper mating with connecting pacts of proper functioning of the device. 3

21、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-60568B 33 m 9999906 0509302 5 m MIL-D-60568B TABLE 1. Ballistic reauirements. Temperature I -65 to -70 I 2.7 -4.2 I I 65 to75 I 2.7 - 3.3 I I I 195 to 205 2.1 - 3.3 3.7.1 Mehl defects. All compon

22、ents shall be free from cracks, splits, cold shuts, inclusions, porosity, or any similar defect. 3.7.2 Burr. No part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel handling the item. 3.7.3 Foreign matter. No part or assembly

23、 shall contain chips, dirt, grease, rust, corrosion, or other foreign matter. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examination

24、s and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the ri

25、ght to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements (see 6.2). 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspecti

26、on set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Go

27、vernment for acceptance comply with all requirements of the contract, Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements; however, this does not authorize submission of known defective material, either indicated or actual, nor

28、 does it commit the Government to accept defective material. 4.1.2 Quality assurance terms and definitions. Reference shall be made to MIL-STD-109 to define the quality assurance terms used. 4.1.3 Inspections. Inspections shall be in accordance with MIL-A-2550 and MIL-STD-453. 4 Provided by IHSNot f

29、or ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-D-bO5688 33 W 9999906 0509303 7 Sample sue 23 Delay bodies 23 Primer retainers 12 (from ballistics sample) 4.2 Clrissification of inspections. 73s inspection requirements specified herein are classified IS a follows:

30、Type of test Destructive Nondestructive X - X - - X a. First article inspection (see 4.4) b. Quality conformance inspection (see 4.5) 3.5.2 4.3 Inspection conditions. Unless otherwise specified in the contract or purchase order (see 6.2), inspection conditions shall be as follows: 4.7.4 Vibration a.

31、 Temperature: Room ambient 68 to 77F b. Altitude: Sea level c. Humidity: 50 percent relative, maximum d. Atmospheric: 14.7 psia 21 4.4 First article inspection. At the beginning of regular production, the contractor shall submit a first article sample to the Government approved facility for evaluati

32、on. The sample shall consist of 23 delay bodies, 23 primer retainers, and 21 delay elements for ballistics, to be tested as indicated in table II, and 10 sets of unassembled components (including explosive components) for visual and dimensional examination. The first article sample shall be manufact

33、ured using the same materials? equipment, processes, and procedures as used in regular production. All parts and materials, including packaging and packing, shall be the same as used for regular production and shall be obtained from the same source of supply, When it becomes necessary to make a chan

34、ge in either the primer, propellant, or igniter lot after initial production, 12 assembled delay elements from the first production lot thereafter shall be tested X - in accordance with 4.7.5. The Government reserves the right to require new first article samples until such time as an acceptable sam

35、ple is submitted (see 6.3). e TABLE II. First article inspection. Paragraph I - Test I 3.4.2 4.7.2 Protective finish 3.6 I 4.7.5 I Function tests 4.4.1 Examination, tests, and facility. After provisional acceptance at source, the sample shall be inspected for all requirements of the drawings and spe

36、cifications at a Government laboratory or other such facility specified in the contract (see 6.2). 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-60.5686 33 9999906 0509304 9 W 9 -. MILD-60568B 4.4.2 Temperature conditioning for ballistic te

37、st. The sample shall be temperature conditioned and tested to determine compliance with 3.6.1.2. The sample for firing shall be conditioned to table III. TABLE III. Temperature conditioning. Temperature (OF) Not vibrated Vibrated -60 to -70 3 4 65 to 75 3 4 I 195 to 205 I 3 I 4 I 4.4.3 Erst article

38、failure. Failure of the sample to comply with the requirements of the drawings and specifications shall result in first article sample disapproval. 4.5 Quality conformance inspection. 4.5.1 Lot. 4.5.1.1 Submission of product. The product shall be submitted in accordance with MIL-STD-105. 4.5.1.2 Lot

39、 size. Unless otherwise specified (see 6.2), the production lot size shall be not more than 1200. 4.5.2 Examination and tests. The quality conformance sample shall be subjected to the examinations of 4.6 and all the test procedures of 4.7 except for 4.7.4. 4.6 Examination. All delay elements and com

40、ponents shall be examined visually and radiographically and characteristics defined in accordance with the applicable drawings. One hundred percent examination shall be performed for all critical defects. Examination for major or minor defects shall be performed on a defect basis in accordance with

41、the classification of defects. Four power (4 X) magnification may be used in performing visual examination for such defects as burrs and foreign matter. When compliance is in doubt as a result of visual inspection, the characteristic shall be measured or gaged to determine acceptability. All nonconf

42、orming items shall be rejected. 4.6.1 Delay Element, M13, Assembly Drawing 8596113. Characteristic Defect Method of Inspection Critical 1 Any part missing 2 Improper assembly 3 Primer not properly seated 6 X-ray/Visual X-ray/Visual X-ray /Visual Provided by IHSNot for ResaleNo reproduction or networ

43、king permitted without license from IHS-,-,-4 5 MIL-D-6056B 33 9999906 0509305 O Primer uncrimpai or seal missing Marking missing, incorrect or illegible Major 101 102 Diameter of body, max 103 Metal defective 104 105 Burr 106 Foreign matter present Concentricity of head with body Protective finish

44、inadequate or defective Minor 201 Total length, rnax 202 Lacquer missing or inadequate 4.6.2 Body Delay, Drawing 8594081, covering a detail of Drawing 8596113. Critical 1 2 Metal defective Flash hole missing or obstructed Major 101 Pitch diameter, external thread, min 102 Major diameter, external.th

45、read, min 103 104 105 106 107 108 109 110 111 112 Concentricity of body with pitch diamcr of thread Diameter of cavity, max Diameter of head, min Diameter of flash hole Diameter of thread relief Length from cavity face to shoulder of head diameter Protective finish inadequate or defective Thread dam

46、aged or not full Burr Foreign matter present Minor 201 202 203 204 205 206 207 208 209 210 Pitch diameter of external thread, max Diameter of wrench hole Diameter of thread pilot Diameter of cavity, min Diameter of head, max Diameter of step rear of head Depth of wrench hole Depth to base of cavity

47、Total length Length of step rear of head 7 Viwd Visud Gage Gage Visual Visual Visual Visual Gage Visual Visual Visual Gage Gage Gage Gage Gage Gage Gage Gage Visual Visual Visual Visual Gage Gage Gage Gage Gage Gage Gage Gage Gage Gage Provided by IHSNot for ResaleNo reproduction or networking permi

48、tted without license from IHS-,-,-MIL-D-605688 13 999990b 0509106 2 MILD-60568B 21 1 Length of thread pilot 212 Width of thread relief 213 Location of wrench hole 2 14 215 Surface finish improper Radius of chamfer missing or incorrect Gage Gage Gage Visuai .7. -4 v 1sual _-_- 4.6.3 Gasket, Aluminum,

49、 Drawing 8594082, covering a detail of Drawing 8596113. Critical None defined Major 101 Diameter, outside, min 102 Diameter, inside, max 103 Metal defective 104 Burr 105 Foreign matter present Gage Gage Visual Visual Visual Minor Diameter, outside, max Gage i 201 202 Diameter, inside, min 203 Thickness 204 Surface finish improper v ISUSU 4.6.4 Primer, Retainer, Drawing 8594083, covering a detail of Drawing 8596113. Critical 1 2